|
|
Joined: Jul 2005
Posts: 1,785
Campfire Regular
|
OP
Campfire Regular
Joined: Jul 2005
Posts: 1,785 |
No doubt everyone here already knows the trick, but I would appreciate a little refinement in my education on this subject.
This much I already know about the high glass finishes Remington uses:
1) Secret DuPont formula 2) Difficult to repair 3) Tough and durable
Specifics: I have a new 700 BDL that got dropped at the range onto a concrete floor. It scratched the finish down to the walnut in 4 different spots, none of which are more than an inch in diameter.
I have read that one could feather sand the damage with 400 grit, re-coat with gloss polyurethane and be on your way. The problem is that this method means you end up with high and low spots. Wet sanding with 1500 will flatten everything, but you are left with a dulled finish.
What is everyone's experience with this? Is it possible to effect a repair?
"I didn't realize we had so many snipers in this country." by J23
|
|
|
|
Joined: Oct 2008
Posts: 621
Campfire Regular
|
Campfire Regular
Joined: Oct 2008
Posts: 621 |
Of course it's possible to repair. It's a matter of building the sanded area back up to above flush with finish and then block sanding it down to match the level of the surrounding finished stock so that you end up flush with 1500-200 grit paper. Then you polish it with automotive polishing compound until it matches the original finish for gloss. It is tedious but a careful workman can make an invisible repair given enough time and technique.
RAN
|
|
|
|
Joined: Jul 2005
Posts: 1,785
Campfire Regular
|
OP
Campfire Regular
Joined: Jul 2005
Posts: 1,785 |
Thanks- it sounds like I was headed in the right direction, just need more coats to give me some "meat" for sanding.
"I didn't realize we had so many snipers in this country." by J23
|
|
|
|
Joined: May 2014
Posts: 10,407
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2014
Posts: 10,407 |
What is the recommended new finish material?
Last edited by Bugger; 08/17/16.
I prefer classic. Semper Fi I used to run with the hare. Now I'm envious of the tortoise and I do my own stunts but rarely intentionally
|
|
|
|
Joined: Feb 2001
Posts: 50,627
Campfire Kahuna
|
Campfire Kahuna
Joined: Feb 2001
Posts: 50,627 |
Cyanoacrylate glue does a great job on gloss 700 stocks...
Mark Begich, Joaquin Jackson, and Heller resistance... Three huge reasons to worry about the NRA.
|
|
|
|
Joined: May 2016
Posts: 169
Campfire Member
|
Campfire Member
Joined: May 2016
Posts: 169 |
What is the recommended new finish material? The original stuff was very close to or a type of clear epoxy. I have used that clear 5 minute epoxy found in most hardware stores with success. As posted you have to get it built up, sand it back down level and then polish it. I used plain white Turtle wax brand polishing compound for the final shine. if you take your time and make it level and polish it good it is a good repair that only you will know about when you look at the gun.
|
|
|
|
564 members (1lesfox, 11point, 007FJ, 12344mag, 160user, 10gaugemag, 55 invisible),
2,920
guests, and
1,226
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,191,355
Posts18,468,899
Members73,931
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|