24hourcampfire.com
24hourcampfire.com
Previous Thread
Next Thread
Print Thread
Hop To
Page 2 of 3 1 2 3
Joined: Jan 2014
Posts: 1,298
D
DIYguy Offline OP
Campfire Regular
OP Offline
Campfire Regular
D
Joined: Jan 2014
Posts: 1,298
I have a lot of time in between coats of Tung oil so I am getting a head start on making some of the accessories Josh will need for the bow. The first thing he needs is a bow stringer.

I took an old bungee cord that I had removed the hooks from because I needed them for some other project and I cut off one end.

[Linked Image]

Then I trimmed off one side to create a flat surface. The flat is the surface that will contact the bow limb when being used. It took two cuts to get it where I wanted it.

[Linked Image]

The other end of the stringer will slip over the limb. This part, I made out of a piece of scrap leather.

[Linked Image]

I folded it in two and punched the stitching holes

[Linked Image]

Then sewed it using white, braided, waxed line.

[Linked Image]

Then I added a grommet for the rope to attach to.

[Linked Image]

Both ends were then connected using a strong nylon rope.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/stringer7.jpg[/img]

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/stringer8.jpg[/img]

To use the string, On end is slipped over the lower limb tip.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/stringer9.jpg[/img]

And the rubber end is placed on the upper side of the other limb. The knot is tied far away from the rubber end to allow for clearance for the bow string to pass through.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/stringer91.jpg[/img]


BP-B2

Joined: Jan 2014
Posts: 1,298
D
DIYguy Offline OP
Campfire Regular
OP Offline
Campfire Regular
D
Joined: Jan 2014
Posts: 1,298
I had Josh try it out on my old longbow since the Tung oil was still wet on his. One hand lifts the bow and the other hand slides the loop of the bow string into the string groove on the limb tip.

[Linked Image]

With the string finished, I moved on to a limb tip protector so that nice white antler limb tip won't become damaged when he sets the tip in the dirt.

I started with two thin pieces of suede leather and stitched them together to make a nice tight fit over the limb tip. I then cut a long slot in the back side for the bow string to pass through.

[Linked Image]

It is a tight fit and that will keep it from falling off.

[Linked Image]

I then trimmed away the extra leather around the outside and tried it with the bow string in place.

[Linked Image]

[Linked Image]

I still need to make a string keeper, an arm guard, a finger tab and a case for the bow as well as a set of arrows.

Joined: Jan 2014
Posts: 1,298
D
DIYguy Offline OP
Campfire Regular
OP Offline
Campfire Regular
D
Joined: Jan 2014
Posts: 1,298
these long breaks have given each coat of finish a long dry time. I received the shafts in the mail so I can now start the arrows for the bow. In the mean time, I had a little time to make Josh an arm guard to go with the new bow.

I used 5 Oz. tooling leather for the face and 4 Oz. Buffalo for the backer.

[Linked Image]

[Linked Image]

I added a little tooling with his initials.

[Linked Image]

And made some antler buttons.

[Linked Image]

I used a dark red/brown stain and attached elastic/bungee material to hold in in place,

[Linked Image]

[Linked Image]

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/armguard4.jpg[/img]

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/armguard5.jpg[/img]

Joined: Jan 2014
Posts: 1,298
D
DIYguy Offline OP
Campfire Regular
OP Offline
Campfire Regular
D
Joined: Jan 2014
Posts: 1,298
In the spirit of this homemade bow project, I wanted to make josh a finger tab to go with the arm guard. At some point I will need to make a quiver as well. I traced the shape of my homemade finger tab for Josh's and cut out 3 of them from some medium thickness scrap leather.

[Linked Image]


I then stacked the 3 and used brass rivets to hold them together.

[Linked Image]

I then began to focus on the arrows for Josh's new bow. I got the shafts From a local vendor. I bought Gold Tip Traditionals because of the wood grain look.

[Linked Image]

After capping the back 9 inches of the shafts with white lacquer, I started cresting the shafts using a color scheme that resembles the riser. I will write Josh's name on all the shafts.

[Linked Image]

[Linked Image]

The fletching will be 4 1/2 inch long LW barred turkey feathers. Since nobody sells 4 1/2 feathers, I bought 5 inch parabolic cut and converted them to 4 1/2 shield cut.

[Linked Image]

Now the fletching begins.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/josharrows5.jpg[/img]

One down, 11 more to go.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/josharrow7.jpg[/img]

Joined: Jan 2014
Posts: 1,298
D
DIYguy Offline OP
Campfire Regular
OP Offline
Campfire Regular
D
Joined: Jan 2014
Posts: 1,298
I'm in the home stretch now. The finish on the bow is now hardened. I have the first half dozen shafts fletched, I gave the bow a good rub down with OOOO steel wool to take off the shine and I made the rug rest and strike plate.

For the strike plate, I used 2-3 Oz. leather and for the rug, I used the fuzzy side of some adhesive backed Velcro strip I had laying around.

[Linked Image]

The leather was from some scrap I had so I needed to add some double sided tape to make it stay on the riser.

[Linked Image]

Then I spent a little time adding a leather grip to the longbow. The finished wood was very slick and needed some texture. I started with a piece of 4 Oz. tooling leather and got it good and wet so I could form it to the shape of the grip. The wet leather is on the right. I gets much darker when you wet it.

[Linked Image]

While it's wet, it can be formed and shaped and stretched to fit the contour of the riser. Once I had it shaped, I used a blow dryer to dry it off.

[Linked Image]

[Linked Image]

So far during this build along, I have been pretty good about taking pictures of each step. Until now. I must be getting tired because I did a bunch of stamping and tooling on the leather but forgot to get pictures of the process. After stamping and cutting the leather to it's final size, I punched some lacing holes. I then applied a coat of rubber cement to both the inside of the leather and the bow's riser.

[Linked Image]

After lacing, I gave the leather a coat of Neats foot oil to restore the oils lost during the working of the leather and from blow drying. The oil makes the leather even darker. Now, you can see the tooling and stamping I forgot to take pictures of earlier.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/grip5-1.jpg[/img]

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/grip6-1.jpg[/img]

Then I took it outside for a picture in natural light.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/grip7-1.jpg[/img]

IC B2

Joined: Jan 2014
Posts: 1,298
D
DIYguy Offline OP
Campfire Regular
OP Offline
Campfire Regular
D
Joined: Jan 2014
Posts: 1,298
The bow project is finished with the exception of the quiver and and the fact that Josh wants to design and make his own broadheads. It was a fun project and I learned a lot of useful stuff for the next bow.

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[Linked Image]

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/done3.jpg[/img]

And finally he got to shot if for the first time.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/firstshot2.jpg[/img]

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/firstshot.jpg[/img]

I then shot the bow through a chorongraph using a 125 grain field point. This brought the total arrow mass to 425 grains. The speed at 28 inches of draw was 174 FPS. This will produce 28.5 Foot pounds of K.E. giving him even more reason to keep any shots on game at less than 20 yards and broadside. This will also be a design consideration when he starts to design the broadhead. All good lessons.

Now, as for naming the bow, We thought on it for some time and kept coming back to the first post where I explained the the bow was being made with a sort of legacy piece of wood. That name stuck. I explained to Josh that this bow is only to be handed down to one of his children. I hope I am around to see that.

[img]http://i28.photobucket.com/albums/c239/212007154/josh%20bow/done4.jpg[/img]

Joined: Jan 2014
Posts: 1,298
D
DIYguy Offline OP
Campfire Regular
OP Offline
Campfire Regular
D
Joined: Jan 2014
Posts: 1,298
[Linked Image]

I bought a new digital camera that will also shoot video so I used Josh as my Guinea Pig. I told him to shot 3 arrows into the target. I had him stand about 5 yards away because I was burning brush in our backyard fire pit and that was where we had to stand to stay out of the smoke.

I told him to fire the 3 arrows and not to talk or look in the camera. His first shot was a dead center hit on the bullseye. The second shot cracked the nock of the first arrow and made it glance out. You can tell by the way he shakes his head that he wants to look at the camera and say something.

Here is my first ever video staring Josh and his homemade custom Longbow.

http://www.youtube.com/watch?v=wsU5S6fwV6g

[Linked Image]

Joined: Jan 2014
Posts: 1,298
D
DIYguy Offline OP
Campfire Regular
OP Offline
Campfire Regular
D
Joined: Jan 2014
Posts: 1,298
Josh's Cross Country and Wrestling scheule kept him from the fall woods. I asked him if I could use his bow to hunt with. He said yes. I hunted several days with it until I encountered a buck one evening and shot it.

I took the below picture the next morning to show where he was standing and made a poor attempt at sketching where he stood.

[Linked Image]

I had plenty of time to tell myself to pick a spot and to take a good aim and then release. The arrow hit a bit high and the deer lurched forward and turned to run back on the trail he came from. About half of my 29 inch arrows was still visible as he ran off. I gave 3 loud blows on my grunt tube and he stopped for a moment and then walked off.

I knew I had hit him high but I was not too far back so I was sure I had hit him in the lungs. I decided to sit for 20 minutes but waited 45 instead since he took off with my arrow. At 4:15 I got down and collected my sponges and went to where he stood to take up the trail. There was no blood to be found but the black muddy kicked up tracks made the trail easy to follow.

After tracking about 40 yards, I spotted a shed antler in the wet leaves.

[Linked Image]

A few feet further I found my broken arrow. the first 6 inches were missing. Too bad as I hoped to get back my homemade broadhead.

[Linked Image]

The first 5 inches of the arrow broke off after passing through the buck.

[Linked Image]

After going another 20 yards I found the only blood that I would find while tracking this deer.

[Linked Image]

It was getting dark as I kept following the muddy trail along the river. It took me all the way to my other ladder stand so I decided to walk out to my truck to drop off the bow and quiver and take up a path that would lead me back to the stand but would parallel the trail that I had just followed about 40 yards closer to the field edge. As I approached my truck, I jumped a deer and my heart sank. I never got a good look at the deer because it was too dark but I still took up the trail back to my stand and if I came up empty I would come back in the morning and take up the trail again.

As I re-entered the river bottom to walk through the tall grass, I stumbled upon my buck. It was just dumb luck to walk into the woods where I did but I will take a bit of good fortune anywhere I can find it.

[Linked Image]

I learned the next morning that the trail I was following branched off and he died about 30 yards past the branch on the other trail. I looked him over and realized that he had died only a few yards from the spot my Uncle Stan used to hunt. Uncle Stan died a few weeks ago and when I put everything together in my mind, I just took a moment to sit in the grass and reflect on Uncle Stan and the fact that I had just realized my goal of harvesting a deer with all homemade gear and to do it in the same woods that Stan and I hunted so many years ago made it a pretty emotional event. Your never too old to shed a tear. I sat there pondering things and giving thanks for my good fortune.

After gutting I examined the deer to find that I had gone through both sides even though the arrow stayed with the deer. I expected to find the front half of the arrow and my homemade broadhead inside the deer but it no resides somewhere along the trail of his final steps. I had hit the top of the near lung and the upper third of the far side lung. He traveled less than 100 yards brfore it expired.

Exit side hole

[img]http://i300.photobucket.com/albums/nn31/WBH_stuff/nov_8hunt/nov8buck93.jpg[/img]

[img]http://i300.photobucket.com/albums/nn31/WBH_stuff/nov_8hunt/nov8buck94.jpg[/img]

[img]http://i300.photobucket.com/albums/nn31/WBH_stuff/nov_8hunt/nov8buck95.jpg[/img]

I couldn't be more pleased with my good fortune. My goal was to take a deer with a homemade bow and arrows, with homemade broadheads and finger tab and homemade camo and I was able to realize that goal in the same woods that I was brought up in. It doesn't get any better than this. I feel very fortunate to have achieved this goal. Now Josh knows his new bow is a proven killer.

Last edited by DIYguy; 04/17/14.
Joined: May 2009
Posts: 4,592
A
Campfire Tracker
Offline
Campfire Tracker
A
Joined: May 2009
Posts: 4,592
Congrats, and this has been an interesting thread from start to present. Very nice work.

Joined: Feb 2011
Posts: 26,389
G
Campfire Ranger
Offline
Campfire Ranger
G
Joined: Feb 2011
Posts: 26,389
Looks great! Very nice work!

IC B3

Joined: Feb 2013
Posts: 629
W
Campfire Regular
Offline
Campfire Regular
W
Joined: Feb 2013
Posts: 629
DIYguy,
Congrats! I am impressed with your talent and can do attitude! Everything from wood working to bowyering to leather working. Absolutely an awesome thread. Thank you for sharing your adventure & experience.

Joined: Oct 2003
Posts: 808
Campfire Regular
Offline
Campfire Regular
Joined: Oct 2003
Posts: 808
Great thread. Nice craftsmanship on that bow. I also have a legacy bow built by my dad and I in my final years of High School. We did most everything very similar, except using Pacific Yew and Bubinga with clear glass. We also used C clamps and inner-tube strips.

I really like the hunting story at the end also.

Awesome!


“I am in love with Montana. For other states I have admiration, respect, recognition, even some affection, but with Montana it is love, and it’s difficult to analyze love when you’re in it.” John Steinbeck
Joined: Feb 2004
Posts: 5,278
T
Campfire Tracker
Offline
Campfire Tracker
T
Joined: Feb 2004
Posts: 5,278
Great build-along. Thanks for sharing that. Very nice bow and story.

Joined: Jul 2007
Posts: 24,590
Campfire Ranger
Offline
Campfire Ranger
Joined: Jul 2007
Posts: 24,590
Flat-out amazing!


[Linked Image from i.imgur.com]

WWP53D
Joined: Aug 2005
Posts: 10,640
Campfire Outfitter
Online Content
Campfire Outfitter
Joined: Aug 2005
Posts: 10,640
Wow, that is awesome! Great work.


A true sportsman counts his achievements in proportion to the effort involved and fairness of the sport. - S. Pope
Joined: Mar 2002
Posts: 9,123
A
Campfire Outfitter
Offline
Campfire Outfitter
A
Joined: Mar 2002
Posts: 9,123
You are very talented...

Joined: Apr 2008
Posts: 2,683
Campfire Regular
Offline
Campfire Regular
Joined: Apr 2008
Posts: 2,683
Sweet!!


Yeah, well, you know, that's just, like, your opinion, man.
Joined: Mar 2010
Posts: 157
Campfire Member
Offline
Campfire Member
Joined: Mar 2010
Posts: 157
Best thread I think I've ever read. Love to try it one day, the story at the end is the reason I love the outdoors. It really does let you connect with the past, be it uncles,dads, mentors, or others, thanks again.


"How vain it is to sit down to write when you have not stood up to live"
Joined: Jun 2011
Posts: 927
A
Campfire Regular
Offline
Campfire Regular
A
Joined: Jun 2011
Posts: 927
Dood... you are my new hero!

Friggin' awesome write-up!

Thanks!


Joined: Feb 2002
Posts: 13,622
Campfire Outfitter
Offline
Campfire Outfitter
Joined: Feb 2002
Posts: 13,622
Thank you for sharing that! Well done on each and every count.

Page 2 of 3 1 2 3

Moderated by  RickBin 

Link Copied to Clipboard
YB23

Who's Online Now
732 members (09wingates, 007FJ, 10gaugemag, 12344mag, 10Glocks, 17CalFan, 73 invisible), 2,927 guests, and 1,296 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums81
Topics1,187,774
Posts18,401,552
Members73,823
Most Online11,491
Jul 7th, 2023


 







Fish & Game Departments | Solunar Tables | Mission Statement | Privacy Policy | Contact Us | DMCA
Hunting | Fishing | Camping | Backpacking | Reloading | Campfire Forums | Gear Shop
Copyright © 2000-2024 24hourcampfire.com, Inc. All Rights Reserved.
Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.3.33 Page Time: 0.105s Queries: 15 (0.002s) Memory: 0.9173 MB (Peak: 1.1049 MB) Data Comp: Zlib Server Time: 2024-03-29 15:44:52 UTC
Valid HTML 5 and Valid CSS