|
Joined: Jan 2011
Posts: 4,625
Campfire Tracker
|
OP
Campfire Tracker
Joined: Jan 2011
Posts: 4,625 |
Switching from Accuchoke concealed tubes to Winchoke external and was wondering if the Winchoke can be finger tightened liek many of the aftermarket extend tubes?
If not, is there a hardware store spanner wrench size that will work or is the Winchester the only way to go?
"My message to my troops is if you see anybody carrying a gun on the streets of Milwaukee, we'll put them on the ground, take the gun away and then decide whether you have a right to carry it." - Milwaukee Police Chief Ed Flynn
|
|
|
|
Joined: Feb 2002
Posts: 32,044
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Feb 2002
Posts: 32,044 |
I use the extended chokes in most of my shotguns and only finger tighten them . I use the extended Win Chokes in my sporting clay Win O&U and only finger tighten.
A Doe walks out of the woods today and says, that is the last time I'm going to do that for Two Bucks.
|
|
|
|
Joined: Jan 2011
Posts: 4,625
Campfire Tracker
|
OP
Campfire Tracker
Joined: Jan 2011
Posts: 4,625 |
Will try that...or at least try it and run a feeler in(finger or an actual gauge) and see if there is a gap versus the accuchoke I have a wrench for. Looking at it, the accu wrench looks to have about the same gripping area as the exterior part of the Winchoke. The Winchester manual mentioned finishing the installation with the wrench, but then warns against over tightening which would seem to be easy to due considering their wrench would seem to create a near cheater bar scenario.
"My message to my troops is if you see anybody carrying a gun on the streets of Milwaukee, we'll put them on the ground, take the gun away and then decide whether you have a right to carry it." - Milwaukee Police Chief Ed Flynn
|
|
|
|
Joined: Sep 2013
Posts: 5,866
Campfire Tracker
|
Campfire Tracker
Joined: Sep 2013
Posts: 5,866 |
Hand tight should be fine but keep a cheak on it as some tubes loosen easily and you don't want that. I use extended chokes and most have a notch for a wrench. I use the closed blade on my sodbuster jr. to keep them tight and to loosen. It wouldn't hurt to put a dab of anti seize compound on the threads so they stay nice and clean, it keeps residues from powder from building up on the threads. Seized choke tubes are very common.
Eating fried chicken and watermelon since 1972.
You tell me how I ought to be, yet you don't even know your own sexuality,, the philosopher,,, you know so much about nothing at all. Chuck Schuldiner
|
|
|
|
Joined: Jan 2011
Posts: 4,625
Campfire Tracker
|
OP
Campfire Tracker
Joined: Jan 2011
Posts: 4,625 |
I don't think the Winchester chokes have notches in them. If it does when it arrives then the "wrench" from my Mossberg tube set can handle it. Have always used some form of anti-seize on the tubes, but recently started using Shell moly lube I bought last fall to stand some chance of using most of it in my lifetime.
"My message to my troops is if you see anybody carrying a gun on the streets of Milwaukee, we'll put them on the ground, take the gun away and then decide whether you have a right to carry it." - Milwaukee Police Chief Ed Flynn
|
|
|
|
Joined: Feb 2002
Posts: 32,044
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Feb 2002
Posts: 32,044 |
I always use Choke Tube Lube on the threads
A Doe walks out of the woods today and says, that is the last time I'm going to do that for Two Bucks.
|
|
|
|
136 members (257wthbylover, 300_savage, 5sdad, 2ndwind, aaronward9, 19 invisible),
1,769
guests, and
958
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,190,599
Posts18,454,511
Members73,908
|
Most Online11,491 Jul 7th, 2023
|
|
|
|