|
Joined: Apr 2011
Posts: 4,350
Campfire Tracker
|
Campfire Tracker
Joined: Apr 2011
Posts: 4,350 |
Did you hit your intended target? If ya hit where you wanted I wouldn't think the charge would be off. Maybe clean the chamber and try some more from the same batch providing you've fired others from this batch before this happened. If not I would pull them and start completely over with FL resizing.
|
|
|
|
Joined: May 2011
Posts: 56,273
Campfire Kahuna
|
Campfire Kahuna
Joined: May 2011
Posts: 56,273 |
#1 guess, case length too great, brass jamming into throat #2 rough chamber #3 seating die out of adjustment, too long COAL, bullet jamming into throat #4 different lot of powder
_______________________________________________________ An 8 dollar driveway boy living in a T-111 shack
LOL
|
|
|
|
Joined: May 2012
Posts: 2,934
Campfire Regular
|
OP
Campfire Regular
Joined: May 2012
Posts: 2,934 |
So I picked up some factory ammo this week because curiosity has the best of me ... I wanted to find out if it's just my reloads. Anyway, I got around to trying them today. Bolt was hard as hell to lock closed and I went ahead and fired the round. Casing stuck in chamber just like my reloads. Stuck tight and had to tap out with my cleaning rod again. Something's up with my chamber. Its so damn hard to see inside the chamber but maybe it's just dirty. I don't know? Any suggestions? I hope nothing is seriously going on ... this rifle has always shot awesome.
==================================================
I'm a proud member of the BGE cult ... yes, I consider myself an EGGHEAD
|
|
|
|
Joined: Nov 2011
Posts: 30,948
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2011
Posts: 30,948 |
How long has it been since you've swabbed the chamber?
Yes, a chamber can become sufficiently fouled to cause cases to stick.
You didn't use logic or reason to get into this opinion, I cannot use logic or reason to get you out of it.
You cannot over estimate the unimportance of nearly everything. John Maxwell
|
|
|
|
Joined: May 2012
Posts: 2,934
Campfire Regular
|
OP
Campfire Regular
Joined: May 2012
Posts: 2,934 |
How long has it been since you've swabbed the chamber?
Yes, a chamber can become sufficiently fouled to cause cases to stick. To be honest ... never. I've never in my life focused specifically on cleaning a chamber in any of my rifles. Barrels and the bore, now that's a different story. This must be a tight chamber to begin with is my guess. I've been trying like hell to get this chamber clean since yesterday and haven't had any luck yet. Bolt is still very hard to close with the factory loaded round. What's a good solvent to soak the chamber with? How do I keep the solvent in there to soak? I have a feeling this fouling is built up in the front end of the chamber where it meets the bore, which is the hardest to get at. I sure don't want to take the chance of scratching or damaging anything. Any suggestions on how to get this daggum chamber clean?
==================================================
I'm a proud member of the BGE cult ... yes, I consider myself an EGGHEAD
|
|
|
|
Joined: Oct 2014
Posts: 563
Campfire Regular
|
Campfire Regular
Joined: Oct 2014
Posts: 563 |
Try using a oversized bore mop to fit the chamber snug... with 91% alcohol -or- lighter fluid -or- brake cleaner (non-chlorinated). Soak it pretty good, insert, twist, etc. Then let it sit. Take it out and wring it dry, towel dry, etc. Do it again. When you're satisfied, use a clean bore mop to remove any excess and dry it.
|
|
|
|
Joined: Aug 2006
Posts: 983
Campfire Regular
|
Campfire Regular
Joined: Aug 2006
Posts: 983 |
I was taught on an M-14 Match gun that after brushing the bore w/solvent you use a chamber brush w/solvent, then patch all dry and lube. Think about it, when a wet patch enters the bore liquid is squeezed out of the patch and settles in the chamber, every time. I always clean the chamber after I clean the bore then run a last dry patch down the bore to pick up anything that might have entered the bore from the chamber, then LOOK. Muddy
|
|
|
|
Joined: Nov 2011
Posts: 30,948
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2011
Posts: 30,948 |
RB, if you have a chamber brush, great, if not just use an pistol bore brush that fits the chamber, then dry with an oversized pistol patch.
If you want to soak it, use one of the foaming cleaners, such as Wipeout or Shooters Choice Extreme Clean.
You didn't use logic or reason to get into this opinion, I cannot use logic or reason to get you out of it.
You cannot over estimate the unimportance of nearly everything. John Maxwell
|
|
|
|
Joined: May 2003
Posts: 10,425
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2003
Posts: 10,425 |
40 cal pistol brush should be fine. Chambers should be swilled out and dried every four or so bore cleanings, or whenever in doubt. At least that's what I do. As for Seafire's idea, yes, I always have handy cleaning rods along and a special stubby jag, flat on the end. If I can't do it with the rod just tippy tapping, then the gun is done and I go home for the BIG tools. Hard rod, like Seafire says, with one caveat. GENTLY run it to bottom on the case, mark the rod at the muslim, wrap the rod with tape, to protect the precious crown. THEN get out the nice hammer or mallet. Pretend this is your approach shot to the 18th green in the final round at the Masters.
Up hills slow, Down hills fast Tonnage first and Safety last.
|
|
|
|
Joined: Aug 2006
Posts: 22,907
Campfire Ranger
|
Campfire Ranger
Joined: Aug 2006
Posts: 22,907 |
and give it a whack......
|
|
|
|
Joined: Nov 2008
Posts: 8,634
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2008
Posts: 8,634 |
Try using a oversized bore mop to fit the chamber snug... with 91% alcohol -or- lighter fluid -or- brake cleaner (non-chlorinated). Soak it pretty good, insert, twist, etc. Then let it sit. Take it out and wring it dry, towel dry, etc. Do it again. When you're satisfied, use a clean bore mop to remove any excess and dry it. This, only soak the bore mop with Kroil oil, using a pistol rod insert into the chamber, the bore mop should be left in the the chamber for a couple of hours. If you want you can mix the kroil with a solvent like trying to clean Moly, but would not use a high ammonia type. Kroil is a penetrating oil that will not dry out and dissipate like alcohol or lighter fluid. After soaking use a pistol brush that fits the chamber and spin it to break all of the crud loose, swab out and lightly oil.
Last edited by Swifty52; 01/23/15.
Swifty
|
|
|
|
586 members (10gaugemag, 1beaver_shooter, 10ring1, 16penny, 17CalFan, 160user, 62 invisible),
2,543
guests, and
1,170
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,191,220
Posts18,466,431
Members73,925
|
Most Online11,491 Jul 7th, 2023
|
|
|
|