Home Forums Hunting & Shooting Custom Rifles & Wildcats Defiance Machine new Controlled Round Feed Action

Does the Templar inlet not have the safety cut out on them ?

Im thinking the Templar inlet would have the safty cutout.
The m70 safe is a pretty new development for Defiance.
Im sure McMillian could alter that, if you talked nice to them.

dave

Dave, RDF,

Do you know if Defiance offers an integral rail that is extended beyond the receiver?

How about a right-hand action, with 3-pos on the port-side?

Thanks,

Jason

Templar inlet has the safety cutout. Templar in a McMillan Hunters Edge:

You can specify no safety cut on any McMillan stock.

Just installed a Huber trigger set at 2.5 lbs on a Defiance Deviant long action currently with magnum bolt and .300 win mag barrel, and that trigger is amazing.

Mine is .250 longer

I didn't see anything either!!!!!!

I've played with Montana actions, new and old, and Defiance push feed actions. The M 1999 actions are no better than a Winchester 70 action. They may advertise themselves as a custom action but the fit and finish does not compare to a Defiance. Unless you pay extra.
Defiance starts with better materials, use better machines, and is run by one of the top people in the industry. Tighter tolerances and every surface is perfect and true from the factory. With a good smith there will be no doubt your gun will shoot bragging size group and be a pleasure to own and use. Less work to find a load it likes, stock that you want, custom barrel, all done how you want.
With a M1999, it would probably shoot well. It would be a good hunting rifle, like a M70. It's built "good enough". But if your going a custom route, spend a little more for a gun that's a true custom. If your stepping up to a true custom M1999 your going to spend just as much for a Defiance built rifle, and the Defiance is better.

C'mon, you know you want about four of 'em...

Ordered a short action LH, with 3 pos safety.

Now the wait begins

I hate you...........lol

The Build:

Defiance, LH, Rebel, Tactical bolt knob, no rail, 3 pos safety

308 Win, Bartlein #4 11.25 twist finished at 20", Threaded for suppressor. Bartlien in install the tube.

Manners MCS-t Stock, Gap Camo.

Sunny Hill machine Hinged Floor Plate.

TImney.

3-10 Nightforce SHV in talleys.

GAP rifles will cerakote in OD Green, pillar bed/Marinetex, etc.

Christmas or so it should be done.

BMT

7 year old thread,

Any updates or thoughts on these actions, and about the CRF………

Ya know how something will just impress the hell out of ya and make you sit up,,,,

That just happened.

I’ve got one. Haven’t used it it yet. Kinda wanna order another with a standard bolt face for a 270/280.

My current one is very slick, but it’s a mag bolt face.

Don’t know if there is a better made for the money.

I can't believe they would choose to build the thing with the stupid coned breech. Apart from that, it's a real nice action. GD

Hmmm... good point. In the 1st pic it snuggles up right close to the bolt handle. It appears you'd have to come up over the top of the safety lever to push it back onto safe.

If anyone has a Long Action Mag they want to sell let me know

so tell me guys: how is this action superior to a pre-64 M70 or post-64 crf M70 action that's been slicked up a bit?

slicker feeding?
more rugged trigger?
smoother action safety?
cheaper?
stronger?
stronger recoil lug?

Educate me here.

I’ll tell ya how it’s superior to me,

It’s available……….In a Lefty version………Did I mention, It’s available..

If your right handed, you may not understand.