If someone would be so kind:
.30-06
Lapua brass
220gr Partition
RS Magnum - I know it is very slow, but it is also dense and my powder availability is very, very limited.
Maybe up to 105% fill and 64,000psi - if I can even get that much in there.
Thanks in advance.
What is your brass capacity, and what is your OAL? Unfortunately I don't have Quickload on this computer to help, but those parameters will help.
Here is a quick run down of what QL shows. Might not be half bad..
Cartridge : .30-06 Spring. (SAAMI)
Bullet : .308, 220, Nosler PART SPSemi 16332
Useable Case Capaci: 58.332 grain H2O = 3.787 cm�
Cartridge O.A.L. L6: 3.340 inch = 84.84 mm
Barrel Length : 24.0 inch = 609.6 mm
Powder : Ramshot Magnum
Predicted data by increasing and decreasing the given charge,
incremented in steps of 2.0% of nominal charge.
CAUTION: Figures exceed maximum and minimum recommended loads !
Step Fill. Charge Vel. Energy Pmax Pmuz Prop.Burnt B_Time
% % Grains fps ft.lbs psi psi % ms
-20.0 87 50.80 2025 2003 28465 7856 89.1 1.741
-18.0 89 52.07 2084 2122 30667 8132 90.7 1.687
-16.0 91 53.34 2144 2245 33069 8394 92.2 1.635
-14.0 93 54.61 2204 2373 35695 8642 93.6 1.584
-12.0 95 55.88 2265 2506 38571 8872 94.9 1.529
-10.0 98 57.15 2326 2644 41728 9083 96.1 1.474
-08.0 100 58.42 2388 2786 45201 9272 97.1 1.420
-06.0 102 59.69 2450 2932 49032 9438 98.0 1.368
-04.0 104 60.96 2512 3083 53270 9579 98.7 1.318
-02.0 106 62.23 2575 3239 57975 9692 99.3 1.269 ! Near Maximum !
+00.0 108 63.50 2637 3398 63218 9775 99.7 1.222 ! Near Maximum !
+02.0 111 64.77 2700 3562 69078 9827 99.9 1.176 !DANGEROUS LOAD-DO NOT USE!
+04.0 113 66.04 2763 3729 75666 9846 100.0 1.132 !DANGEROUS LOAD-DO NOT USE!
+06.0 115 67.31 2826 3901 83105 9844 100.0 1.089 !DANGEROUS LOAD-DO NOT USE!
+08.0 117 68.58 2889 4077 91550 9833 100.0 1.047 !DANGEROUS LOAD-DO NOT USE!
+10.0 119 69.85 2952 4258 101205 9812 100.0 1.007 !DANGEROUS LOAD-DO NOT USE!
Results caused by � 10% powder lot-to-lot burning rate variation using nominal charge
Data for burning rate increased by 10% relative to nominal value:
+Ba 108 63.50 2767 3740 79324 9259 100.0 1.121 !DANGEROUS LOAD-DO NOT USE!
Data for burning rate decreased by 10% relative to nominal value:
-Ba 108 63.50 2445 2920 50013 9721 94.2 1.355
Thanks for the help.
RiverRider - why not compress it? I usually don't do compressed loads but have in the past - mostly with H870 in 7mm RM.