Loads?
Results?
Good for fur?
Good for shooting pigs in the face?
What say you Campfire loonies?
I don't know, but I've been meaning to use one. I have a few boxes of 250.
I'd rather 62X,by a goodly margin.
28grs of '335 in all of mine in twist 7,8 and 9"...even with the shortest throat.............
Gonna be shooting some varmints as well as pigs, don't wanna use up the TSXs on the little dudes�
But thanks guys.
That damn H335 is the 'go to' load in my rifles whilst shooting TSXs�found out its giving me the velocity with Barnes that others aren't�.otherwise I hate that stuff...
After killing a few pigs and seeing the vital area between the eyes on an 'eater' is only a couple inches wide, I came to the conclusion that just about any bullet landed in there will blow it up, and a 60 grainer on the smaller ones oughta put a cavity through the body cavity�if need be.
Every time I buy something other than 335 for my SAAMI 223 I wish I hadn't
I can't say the same but it shire do produce the velocity and accuracy for the hunting loads! It is indeed my 'go to' for TSXs...
If not a 62TSX...I'd just as soon stay 50V-Max................
Good for cats in the face.........
26.7 Varget in the above rifles and a Montana as well, Montana prefers '335 both loads very accurate. All SAAMI, 'AI only gets fed 75 'Max, that kills the siht out of pigs for conversation. Nothing fur friendly about it, blows siht up like any other B-tip or V-max. Wouldn't hesitate to use it on deer or pigs.
If not a 62TSX...I'd just as soon stay 50V-Max................
Odd you say that�thus far, if it isn't gonna get a TTSX, my load is a 50 V-max�.got three AIs and they all like the same load.Cant argue with that.
I'm sure the 50 Vmax would do what I have in mind this time�but I just gotta fugg with stuff�.
That's my poison, 26.5 H335 , 50 vmax. A titch under 3500fps and just as accurate as I can shoot.
Getting the same out of 28.0 gr IMR 4895�.
Shoots better than I can...
That's my poison, 26.5 H335 , 50 vmax. A titch under 3500fps and just as accurate as I can shoot.
I shoot 30grs of '335 in all (13) of mine...twist rates ranging from 7-14",with most stops in between.................
I eased and oozed mine up to 30 grains but thats where we stopped and backed off, primers blown and all the bad stuff you hear about 335 happened. Must be cause its so hot here
The 55TTSX LOVES 28.5 grains ��..
Happy for you�.no worky for me.
My R-15 remington AR loves them, not the AI but...
Happy for you�.no worky for me.
You are still missing it...which is of course the best part.................(grin)
Thats it! I'm putting your cyber-bullying little ass on Uber-Pretend Ignore!
See how THAT feels!
Gotta go up to the range now and shoot some 223AI loads with no H335 in them�..
Happy for you�.no worky for me.
You are still missing it...which is of course the best part.................(grin)
If you mean the before/after pics of the bolt face work�I got that�.
I'm not as think as you dumb I am�.
3500fps 50's is SAAMI 223 Territory and I'm not going to form cases,simply to yank spark plugs...though noone loves to form cases more than I. Hint.
1000 more words.
Re-hint..................(hint)
By gawd,you may be onto sumptin'...............(grin)
The Rock is a 21-incher squirting 50's at 3750fps,if only for conversation..............
'Nother headed out this afternoon.
Before...and it's horrible sloppy.
1,000,000 Words................(hint)
Whats that hole in the middle for?
On another note, I have discovered the ultimate, consummate shoot pigs in the face load using 60 gr NBTs�.
Cant wait to try it out�.
335 is a bitch here in the Texas heat. 8208xbr takes its place very nicely with both the 62 ttsx and the 75's amax/hpbt - but be careful, when you reach the max it comes quick!
I like my 62's at 3400 and my 75's at 3100+.
Hint.............
Bushed firing pin, tight headspace allows you to reach the top end pressure(accuracy) node....you have to see it to believe it. Call Greg Tannel of Gre-Tan rifles for the fix.
Now start at the start, reamer design = tight throat dia(.2245), minimum freebore(compress the 75's, stuff the bullet in the case), tight body on the reamer(minimum SAAMI match specs), Dia at the web(+.002) the brand of brass you are using...expect nothing but stellar results on what's to follow!
Dave Kiff makes the reamers for Redding's dies....Match reamer specs to dies!
Big Hint!
You are in sooooooooooo far over your head,it's plum amazing.................
Bushed firing pin, tight headspace allows you to reach the top end pressure(accuracy) node....you have to see it to believe it. Call Greg Tannel of Gre-Tan rifles for the fix.
Now start at the start, reamer design = tight throat dia(.2245), minimum freebore(compress the 75's, stuff the bullet in the case), tight body on the reamer(minimum SAAMI match specs), Dia at the web(+.002) the brand of brass you are using...expect nothing but stellar results on what's to follow!
Dave Kiff makes the reamers for Redding's dies....Match reamer specs to dies!
Which Part?
I've never not seen you be a dumb [bleep]....................
Hee Hee! I'm still learning!
It ain't happening.
Hint.................