#2025138 - 02/17/08 10:52 PM
My Marlin Mountie is very stiff
|
kevinh1157
Campfire Regular
Registered: 10/21/03
Posts: 507
Loc: Occupied California
|
Offline
|
|
I recently picked up a Marling Mountie. When I got it, the action was very stiff and the lever hard to operate. I took it apart and gave it a thorough cleaning (MUCH needed) but it is still hard to operate. I had my gunsmith take a look at it and can find nothing wrong. Any ideas before I send it back to Marlin for service?
_________________________
Kevin Haile
|
|
Top
|
|
|
|
|
#2026378 - 02/18/08 01:56 PM
Re: My Marlin Mountie is very stiff
[Re: kevinh1157]
|
Stillwater
Campfire Regular
Registered: 05/24/05
Posts: 258
Loc: In the far West
|
|
Offline
|
|
If the gunsmith you use could not see what to do to smoothup the Marlin, you need to go to another gunsmith...
All Marlins are a little stiff, when new. Shoot the rifle and it will break in. Why do I know? I have eight Marlin 39's.
If you are in, or close to, the San Fernando Valley, I can send you to a gunsmith that can take care of your very minor problem with the Marlin...
Bill
Edited by Stillwater (02/18/08 01:57 PM)
|
|
Top
|
|
|
|
|
#2027262 - 02/18/08 07:56 PM
Re: My Marlin Mountie is very stiff
[Re: Stillwater]
|
kevinh1157
Campfire Regular
Registered: 10/21/03
Posts: 507
Loc: Occupied California
|
|
Offline
|
|
Bill thanks for the reply. The gun is an older Mountie I bought used. From the accumulated powder etc. in the action, it has had many thousands of rounds through it. One of the things I did was to be JB Bore Shine on all the bearing surfaces and rack the action 500 times (followed with clean and lube in an ultra sound cleaner. No change. I've had other Marlins new and understand they are a little stiff when new. This rifle is orders of magnitude different in stiffness than mere break-in. Any help?
P.S. - I grew up and went to school in the Valley (Chaminade Prep and CSUN). I still get down there now and again, who do you recommend as a gunsmith (There are very few gunsmiths in the Bay Area and the best is closing shop and moving to Truckee)
Edited by kevinh1157 (02/19/08 12:35 PM)
_________________________
Kevin Haile
|
|
Top
|
|
|
|
|
#2027304 - 02/18/08 08:11 PM
Re: My Marlin Mountie is very stiff
[Re: kevinh1157]
|
Stillwater
Campfire Regular
Registered: 05/24/05
Posts: 258
Loc: In the far West
|
|
Offline
|
|
Bill thanks for the reply. The gun is an older Mountie I bought used. From the accumulated powder etc. in the action, it has had many thousands of rounds through it. One of the things I did was to be JB Bore Shine on all the bearing surfaces and rack the action 500 times (followed with clean and lube in an ultra sound cleaner. No change. I've had other Marlins new and understand they are a little stiff when new. This rifle is orders of magnitude different in stiffness than mere break-in. Any help?
P.S. - I grew up and went to school in the Valley (Chaminade Prep and CSUN). I still get down there now and again, who do you recommend as a gunsmith (There are very few gunsmiths in the Bay Area and the best is closing shop and moving to Trukee)
I have been a friend of Jim Hoag, since he started in 1962.
If you go to the 1911 forum, you will see he is considered one of the ten top gunsmiths, working on the 1911 pistols, extant.
James Walter Hoag
8523 Canoga Ave.
Canoga Park, CA 91304
(818) 998-1510
Tell Jim that Bill Ward recommended you, to him... That won't get me anything, however, he will pay very, very close attention to your rifle.
Bill
|
|
Top
|
|
|
|
|
#2028627 - 02/19/08 12:34 PM
Re: My Marlin Mountie is very stiff
[Re: Stillwater]
|
kevinh1157
Campfire Regular
Registered: 10/21/03
Posts: 507
Loc: Occupied California
|
|
Offline
|
|
Thanks Bill
_________________________
Kevin Haile
|
|
Top
|
|
|
|
|
#2046581 - 02/26/08 12:34 PM
Re: My Marlin Mountie is very stiff
[Re: kevinh1157]
|
Lastmohecken
Member
Registered: 10/01/07
Posts: 77
|
|
Offline
|
|
Check your takedown screw, you know the big thumb screw. I have an older mounty but it was unfired when I got it. I took it down, and cleaned it, put it back together and tighened the thumb screw by hand with my fingers. The gun looked to be totally together, and assembled correctly.
This wasn't my first 39 either, I have had a couple before this one. Anyway the action was very stiff and rough, but it was quite a bit slicker before I took it apart, so I knew I had not done something right. Anyway, after carefully considering everthing, I put a big screwdriver on the thumb nut and found that it needed tightening some more. After that, the rife was much slicker, so be sure that screw is tight, tighter then just by hand, you will know when it's right.
This might not be your problem, but it was on mine.
|
|
Top
|
|
|
|
Moderator: RickBin, SYSOP
|
|
|
|
|
1
|
2
|
3
|
4
|
|
5
|
6
|
7
|
8
|
9
|
10
|
11
|
|
12
|
13
|
14
|
15
|
16
|
17
|
18
|
|
19
|
20
|
21
|
22
|
23
|
24
|
25
|
|
26
|
27
|
28
|
29
|
30
|
31
|
|
|
18939 Members
65 Forums
198076 Topics
2438779 Posts
Max Online: 1366 @ 08/07/07 07:51 PM
|
|
|
