|
Joined: Dec 2004
Posts: 291
Campfire Member
|
OP
Campfire Member
Joined: Dec 2004
Posts: 291 |
I am getting ready to refinish a stock. Normally I have used True Oil. it seems to require a lot of coats and is tedious. The positive attributes is that is easy to refinish if you have accidents. Also, I have tried polyurethane but always seem to get runs. What are alternatives and do they all require multiple coats. I will be satisfied with a good waterproof satin finish. It is on a hunting rifle. Nothing fancy required.
|
|
|
|
Joined: Jan 2001
Posts: 7,986
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2001
Posts: 7,986 |
Lacquer is probably the toughest gun stock finish you can find and relatively easy to put on. Get a couple rattle cans of satin finish Lacquer at your local Home Depot and put it on with several light coats until you have the coverage you want. Let it dry a few days and go hunting. Of course, prep is important as in all finishes. Either strip the existing finish down to wood or sand it down to a good, flat surface.
Bob
Never underestimate your ability to overestimate your ability.
|
|
|
|
Joined: Feb 2001
Posts: 50,619
Campfire Kahuna
|
Campfire Kahuna
Joined: Feb 2001
Posts: 50,619 |
Never use a satin finish for anything you actually want to protect... The flattening agents in finish are usually silica and do nothing positive for the finish. It is less durable and far less waterproof.
To get a satin finish use gloss finish and then knock the shine off with either rottenstone in mineral oil of felt or use Bear-Tex pads.
Mark Begich, Joaquin Jackson, and Heller resistance... Three huge reasons to worry about the NRA.
|
|
|
|
Joined: Nov 2006
Posts: 4,419
Campfire Tracker
|
Campfire Tracker
Joined: Nov 2006
Posts: 4,419 |
If you go with lacquer over either a stripped bare wood stock or one you have sanded down but have not gotten to bare wood you want to hit a coat or two of shellac as a sealer prior to the lacquer. putting lacquer over some finishes mat result in the lacquer eating away at what previous finish is still on the wood. if it does though, don't worry, you'll know it!
Help keep our sport going. take a kid outdoors!
|
|
|
|
Joined: Dec 2006
Posts: 1,420
Campfire Regular
|
Campfire Regular
Joined: Dec 2006
Posts: 1,420 |
If your getting runs, you are applying way too much finish at a time. Wipe on, wipe off. A slightly wet pad & many coats are all you need.
|
|
|
|
Joined: Jun 2009
Posts: 3,961
Campfire Tracker
|
Campfire Tracker
Joined: Jun 2009
Posts: 3,961 |
A stock refinishing sticky would be nice.
"I was born in the log cabin I helped my grandfather build"
|
|
|
|
Joined: Feb 2013
Posts: 168
Campfire Member
|
Campfire Member
Joined: Feb 2013
Posts: 168 |
Try timberluxe by Brian Board . . . Great stuff!
"We've had enough of exhortations to be silent! Cry out with a hundred thousand tongues! I see that the world is rotten because of silence!" St. Catherine of Sienna
|
|
|
|
Joined: Feb 2010
Posts: 17,761
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2010
Posts: 17,761 |
+1 on Timberluxe, easy to use and produces great results. Check the website for an instructional video. I have used both the finish and the stain, only thing is I wish the stain was available in a smaller container.
|
|
|
|
Joined: Jul 2011
Posts: 6,143
Campfire Tracker
|
Campfire Tracker
Joined: Jul 2011
Posts: 6,143 |
Gunswizard, what did you use the finish on. Does the Timberluxe go on before or after the stain?
Fight fire, save lives, laugh in the face of danger.
Stupid always finds a way.
|
|
|
|
Joined: Feb 2010
Posts: 17,761
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2010
Posts: 17,761 |
I used the finish on a Springfield 1922 M2 stock and a Winchester M/52 Sporter stock. On the M2 I applied the stain first and then the finish, the M/52 stock was already finished and I wanted to darken it so I applied the stain and it penetrated thru the existing finish. I was satisfied with both jobs.
|
|
|
|
Joined: Dec 2004
Posts: 291
Campfire Member
|
OP
Campfire Member
Joined: Dec 2004
Posts: 291 |
To EdM; I went ahead and got the Pro Custom Oil from Brownells. After I installed pillars, I stripped the stock (it was a Boyds stock - walnut classic) and wet sanded up to 400 Grit using paint thinner. Then 0000 steel wool rub down. So far I have done 2 coats and I am impressed. The Boyds finish had been mudded so it was featureless. Underneath it is a good looking piece of black walnut. It should finish out very well. Thank you for the tip EdM. Been puttering with it about a week now. Patience, Patience Patience.
|
|
|
|
Joined: Dec 2009
Posts: 1,310
Campfire Regular
|
Campfire Regular
Joined: Dec 2009
Posts: 1,310 |
Any pics? I have used True oil also and was happy with the results but always looking for other ideas. Sanding with paint thinner is a good tip, thanks
USE ENOUGH GUN (Ruark) and YOU CAN'T EVER HAVE TOO MANY (me)
|
|
|
|
Joined: Nov 2002
Posts: 33,653
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2002
Posts: 33,653 |
To EdM; I went ahead and got the Pro Custom Oil from Brownells. After I installed pillars, I stripped the stock (it was a Boyds stock - walnut classic) and wet sanded up to 400 Grit using paint thinner. Then 0000 steel wool rub down. So far I have done 2 coats and I am impressed. The Boyds finish had been mudded so it was featureless. Underneath it is a good looking piece of black walnut. It should finish out very well. Thank you for the tip EdM. Been puttering with it about a week now. Patience, Patience Patience. Great to hear. It really is great stuff.
Conduct is the best proof of character.
|
|
|
|
Joined: Nov 2007
Posts: 196
Campfire Member
|
Campfire Member
Joined: Nov 2007
Posts: 196 |
I strip the stock sand down till there is no fuzz sticking up when wet. Then I put 2 coats of boiled linseed oil and let dry for a few days then start applying spray lacquer and use 000 steel wool in between coats till all grain is filled in. Steel wool one last time and use a wax and buff it. Comes out nice and durable. And a satin finish.
|
|
|
|
Joined: Sep 2009
Posts: 7,289
Campfire Tracker
|
Campfire Tracker
Joined: Sep 2009
Posts: 7,289 |
I second the Pro Stock Custom Oil. Good stuff. Waterlox sounds interesting. From what I understand it's a modern high quality spar varnish. I have used it for other applications, but I am intrigued with spar varnishes for gun stock work. They sound like an all-in-one pour filler and final finish.
"The universal aptitude for ineptitude makes any human accomplishment an incredible miracle." John Stapp - "Stapp's Law" "Klaatu barada nikto"
|
|
|
|
665 members (12344mag, 10gaugemag, 10ring1, 160user, 11point, 10gaugeman, 77 invisible),
2,579
guests, and
1,345
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,190,471
Posts18,451,705
Members73,901
|
Most Online11,491 Jul 7th, 2023
|
|
|
|