Home Forums Hunting & Shooting Rimfires what rings/mounts are you using for CZ452?

The mounts on my rimfire CZ452 may not be the right mounts because the bolt keeps hitting my scope. I am using Millett which I had on hand but probably need to get some mounts for the 2-7x33 scope I am wanting to put on this rifle.

When i had my CZ455 i ended up using Burris Signature med rings without issue.

On my 452 American I used Weaver 22 rings, they give adequate clearance with a Leupold eyepiece and also with a Nikon eyepiece. $8.99 at Walmart.
452's other than the American have a different dovetail width though so if yours is one of those they may not work (11mm I think).

drover

I'm using the Warne 22 rimfire rings (http://warnescopemounts.com/product/721-1-inch-7-322-medium-rings/) but I don't use scopes with large diameter eyepieces.

I use the same setup. Works great.

I used BKL with a Leupold 2x7

I use the Warne as mentioned above.


Informative, extensive listing of what other folks use on rimfire.com.

Click here

I use a lot of Conetrols.

Don't much care for others listed. Although, have some others that came on rifles I picked up. Eventually change them up . Will not use "turn -in" rings.

I see some rings listed on the classifeds for a CZ.

on my 452 Americans with Burris 3-9x40s I'm using Burris deluxe rimfire high rings.

CZ 452 American - BKL Medium rings, Nikon 3x9x40 Rimfire
CZ 452 Ultra Lux - BKL Medium rings, Nikon 3x9x40 EFR

No problems.

Buy one of these and some Burris Signature's and be done with all that other schit.

https://www.diproductsinc.com/Detail.aspx?PROD=156323&CAT=3600





Travis

These in both High and medium variants.

I like split rings on my rifles with integral bases.

I have Tally's on mine.....if you go to their web site thay have a model designed specifically for the CZ.

They ain't cheep but good chit seldom is and Tally split rings are not only strong they're a work of art.

FieldGrade: I have the Leupold 4x rimfire scope and the bottom rifle in your picture , is that the Talleys specifically for CZ? Are those the low or med Talleys? Does the bolt hit the scope with what appears to be low on yours?

I am going to have to order some online obviously as no one carries them locally. I saw a post that the Leupold 2-7x33 (not a rimfire scope) will work for rimfires (I did not htink they can with parallex set at 100 yards) so I will use that or the Leupold EFR scope I have and would like to get scope as close to rifle. This is why I am inquiring whether I should get lows or meds.

Can't wait to get this and hit the squirrel woods eh...

Thanks for the link. Took me a bit to find the lefty ones, since I have a lefty CZ 452 heading my way. My only spare scope laying around is an SWFA 6x, so that should slap nicely onto the CZ.

Burris Signature High Rimfire Rings on my CZ 455. They give good bolt and scope clearance with a Weaver V16 . They work well and the price is reasonable.

BKL's are hard to beat for the price, friend of mine uses the lower priced Weavers on his trainer and they work for him

Those are Med's....Tally doesn't offer lows in that model.....

And no.....the bolt handle does not hit the scope.....I wouldn't use them if it did.

Tally's are not only a split ring design which I prefer on rifles with integral bases but the're actually cut to match the odd dovetail angle CZ uses. They're expensive but worth every penny IMO.

http://www.talleymanufacturing.com/Products/Rimfire-Specialty-Rings/CZ-(1)/CZ-452,-453-American-1-Med-Fixed-Talley-Rings.aspx