One down, one to go. BCA side charger 5.56, $40 lower and cheap chit parts kit from Discount AR. $390 + $44 in sights and $10 vert grip that were on hand. Previously assembled as a pistol BTW....
"I can't be canceled, because, I don't give a fuuck!" --- Kid Rock 2022
Mucho better cheap parts on #2. PSA 10.5" 5.56 pistola KAK, enhanced trigger. $40 lwr. $420+ $60 rear sight on hand. Will get a carry handle as I like them.
Last edited by MtnBoomer; 06/26/20.
"I can't be canceled, because, I don't give a fuuck!" --- Kid Rock 2022
The trickiest part for me is always that little detent and spring for the front takedown pin. Getting that little bugger in place without launching it into orbit takes focus.....grin
Yah for sure. I'll use double ear protection when not suppressed. Looking forward to trying them. Shot my 10.5" Ruger the other day out the rig's window and shattered my driver's side mirror with either the blast or ejected shell! LOL Use with caution. That 7" sucker is awful short, could easily reach out too far.
"I can't be canceled, because, I don't give a fuuck!" --- Kid Rock 2022
I like the looks of the first one. What brand of handguard did you use?
It's a Bear Creek assembled upper and just whatever they were shipping, 15" M-Lok. It was $255 during a sale they had.
I'll note that a few years ago I wanted a dead nuts reliable carbine for my first AR15 and got the FN15 pictured in the group shot, right. If the SHTF, it's the real deal. Others are to play with, but, the Ruger pistol has been pleasing me and is at the ready. If'n I was stuck in a truck at an intersection, I think one of these would be awful comforting. Get'em while you can.
Last edited by MtnBoomer; 06/26/20.
"I can't be canceled, because, I don't give a fuuck!" --- Kid Rock 2022
The trickiest part for me is always that little detent and spring for the front takedown pin. Getting that little bugger in place without launching it into orbit takes focus.....grin
There is a handy little tool for that in my Avid Armorers Tool Kit. Makes it very simple.
The trickiest part for me is always that little detent and spring for the front takedown pin. Getting that little bugger in place without launching it into orbit takes focus.....grin
Buddy showed me the clevis pin trick, which makes that a piece of cake...
The trickiest part for me is always that little detent and spring for the front takedown pin. Getting that little bugger in place without launching it into orbit takes focus.....grin
Buddy showed me the clevis pin trick, which makes that a piece of cake...
The 10.5" PSA is fun, will be funner with my Nomad, if the fugg'n ATF would just send my tax stamp that was approved 9 months ago, 14 months and ticking.
The 10.5" PSA is fun, will be funner with my Nomad, if the fugg'n ATF would just send my tax stamp that was approved 9 months ago, 14 months and ticking.
After some time with the "pistols" I would love to have a stamp and a proper stock. Eventually I will head that direction.
But, for now, I just threw my net worth at ammo components! Damn, got to be slim pickings quick!
Appreciate the good folk's input and discussion here. For the naysayers, just wait till I try to put an upper together you mofos!
At $70 I got 3. Built one into a 16" mid-length, one into a 12.7 carbine length pistol, and not sure on the 3rd yet. They got some bad reviews but all mine have been in spec and fit all my lowers fine. Paired with a pinned front sight gas block barrel they make for a tough set up.
Here is my 12.7". It is a blast in every sense of the word
The 10.5" PSA is fun, will be funner with my Nomad, if the fugg'n ATF would just send my tax stamp that was approved 9 months ago, 14 months and ticking.
I got the call! Octane 45 to be set free at last. Two years ago Silencerco had a BOGO deal. After a long backorder delay, dealer change and much extra delay on my end finally getting in to do the paperwork last December. So, 7 months, non-trust. The Omega 300 took 12 months. Couple of 300 BO projects for the Octane. Yahoo.
That upper seems like it would be awesome. Thanks for the tip.
Originally Posted by CORDrew
If you like projects AND carry handles try one of these:
At $70 I got 3. Built one into a 16" mid-length, one into a 12.7 carbine length pistol, and not sure on the 3rd yet. They got some bad reviews but all mine have been in spec and fit all my lowers fine. Paired with a pinned front sight gas block barrel they make for a tough set up.
Here is my 12.7". It is a blast in every sense of the word
"I can't be canceled, because, I don't give a fuuck!" --- Kid Rock 2022
The 10.5" PSA is fun, will be funner with my Nomad, if the fugg'n ATF would just send my tax stamp that was approved 9 months ago, 14 months and ticking.
I got the call! Octane 45 to be set free at last. Two years ago Silencerco had a BOGO deal. After a long backorder delay, dealer change and much extra delay on my end finally getting in to do the paperwork last December. So, 7 months, non-trust. The Omega 300 took 12 months. Couple of 300 BO projects for the Octane. Yahoo.
That upper seems like it would be awesome. Thanks for the tip.
Originally Posted by CORDrew
If you like projects AND carry handles try one of these:
At $70 I got 3. Built one into a 16" mid-length, one into a 12.7 carbine length pistol, and not sure on the 3rd yet. They got some bad reviews but all mine have been in spec and fit all my lowers fine. Paired with a pinned front sight gas block barrel they make for a tough set up.
Here is my 12.7". It is a blast in every sense of the word
Welcome to my world.. almost. Took ~ 2 years to get one of my Silencerco .30 cal cans during O'Zero's crap.
This was with a trust.
Slaves get what they need. Free men get what they want.
The trickiest part for me is always that little detent and spring for the front takedown pin. Getting that little bugger in place without launching it into orbit takes focus.....grin
Originally Posted by Geno67
Trump being classless,tasteless and clueless as usual.
Originally Posted by Judman
Sorry, trump is a no tax payin pile of shiit.
Originally Posted by KSMITH
My young wife decided to play the field and had moved several dudes into my house
At $70 I got 3. Built one into a 16" mid-length, one into a 12.7 carbine length pistol, and not sure on the 3rd yet. They got some bad reviews but all mine have been in spec and fit all my lowers fine. Paired with a pinned front sight gas block barrel they make for a tough set up.
Here is my 12.7". It is a blast in every sense of the word
Nice.
Originally Posted by Geno67
Trump being classless,tasteless and clueless as usual.
Originally Posted by Judman
Sorry, trump is a no tax payin pile of shiit.
Originally Posted by KSMITH
My young wife decided to play the field and had moved several dudes into my house
Got the Octane and fixed 5/8" mount and stumbled into 100 rounds of subsonic ammo very reasonably priced for today's market. Get the RAR Ranch 300 BO Friday and an AR barrel shipped today. Shhhhhh!
"I can't be canceled, because, I don't give a fuuck!" --- Kid Rock 2022