|
|
Joined: May 2009
Posts: 616
Campfire Regular
|
OP
Campfire Regular
Joined: May 2009
Posts: 616 |
I am in need of the large bolt cam pin on the late Model REM 760 (not 7600) . Do any of you gunsmiths know the dimensions of this round end pin? Looks like it is about 3/8 x 3/16 with rounded ends. Impossible to find from parts dealers. THX
The difference between genius and stupidity is that genius has its limits.- Albert Einstein
|
|
|
|
Joined: Jan 2001
Posts: 59,128
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2001
Posts: 59,128 |
Have you tried Laib's Gunsmithing in Spicer, MN?
(320) 796-2686 201 Highway 23 NE Spicer, MN 56288
Ex- USN (SS) '66-'69 Pro-Constitution. LET'S GO BRANDON!!!
|
|
|
|
Joined: May 2002
Posts: 9,964
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2002
Posts: 9,964 |
Try Ahlmans gun shop in Minnesota also.
|
|
|
|
Joined: May 2009
Posts: 616
Campfire Regular
|
OP
Campfire Regular
Joined: May 2009
Posts: 616 |
Will do, thank you for the suggestions.
The difference between genius and stupidity is that genius has its limits.- Albert Einstein
|
|
|
|
Joined: May 2002
Posts: 9,964
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2002
Posts: 9,964 |
you might want to put a WTB on the huntingpa.com website
|
|
|
|
Joined: Dec 2002
Posts: 32,124
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Dec 2002
Posts: 32,124 |
Have you tried Ahlman's in Morristown, MN? www.ahlmans.com or 507-685-4243 or 4244 Gunsmith questions? mike ahlmans.com I always try GPC first, but if they don't have it, I try Jack First in Rapid City, SD. www..jackfirstinc.com
|
|
|
|
Joined: May 2009
Posts: 616
Campfire Regular
|
OP
Campfire Regular
Joined: May 2009
Posts: 616 |
Found one thanks for the leads.Thanks to all who responded.
Last edited by Milwroad; 07/19/21.
The difference between genius and stupidity is that genius has its limits.- Albert Einstein
|
|
|
|
Joined: Jul 2016
Posts: 615
Campfire Regular
|
Campfire Regular
Joined: Jul 2016
Posts: 615 |
The original pin was a Groove pin which was a standard hardware purchase for Remington. I don’t remember the size but have replaced them with the proper sized drill bit shank, somewhere on the 40’s I think. The Groove pin has a groove down the side to allow it to bite into the hole it is installed into and stay put. When using a drill bit shank, I would peen the outer edge of the hole after installation to retain the pin. A proper sized roll pin may work.
|
|
|
|
565 members (222ND, 1eyedmule, 12344mag, 2003and2013, 10Glocks, 222Sako, 69 invisible),
2,555
guests, and
1,277
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,190,675
Posts18,456,176
Members73,909
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|