24hourcampfire.com
24hourcampfire.com
Previous Thread
Next Thread
Print Thread
Hop To
Page 1 of 2 1 2
Joined: Jan 2018
Posts: 2,041
H
Hesp Offline OP
Campfire Regular
OP Offline
Campfire Regular
H
Joined: Jan 2018
Posts: 2,041
Got in some new orange/brown colored pc powder today. Put the bullets in an old cool whip tub with some Air Soft black BB's, & PC powder. Swirled around for about 45 sec's. They were well coated after this. Preheated my oven to 375dg. Set for "Air Fry", not bake. Placed bullets on non stick aluminum foil. Made sure no bullets were touching. Bullets were handled[Linked Image from i.postimg.cc] with needle nose pliers only. Bare fingers will cause the coating to come off. After 12 min. I could see the coating had melted & the bullets were bright/shinny. These are gas check bullets that were sized before coating to apply the GC. I resized after coating had dried completely to .430". Came out decent. 265gr. will be a day or two before I can get around to shooting.

Last edited by Hesp; 06/07/21.
BP-B2

Joined: Feb 2009
Posts: 11,891
P
Campfire Outfitter
Offline
Campfire Outfitter
P
Joined: Feb 2009
Posts: 11,891
I have found when cooking bullets with gas checks they don't need to cook as long as plain bullets.
Somewhere around 12 minutes or so.

They have been used in rifles and have passed the hammer test.

The coating stays put.

Joined: Jan 2018
Posts: 2,041
H
Hesp Offline OP
Campfire Regular
OP Offline
Campfire Regular
H
Joined: Jan 2018
Posts: 2,041
Did some more casting & coating today. 250gr PB 44 cal & 350gr GC 45cal ( 45-70 ) . Starting to get the hang of this procedure. Once you do it a time or two you see how easy it is. Shooting these coated bullets is great. Accurate & "NO" leading. The 44's are on the left & 45's on the right.[Linked Image from i.postimg.cc] These bullets are sized & ready to shoot.

Last edited by Hesp; 06/09/21.
Joined: Jan 2001
Posts: 10,843
M
Campfire Outfitter
Online Content
Campfire Outfitter
M
Joined: Jan 2001
Posts: 10,843


Today would be a good day for “shake and bake” powder coating here at my house.... 94 degrees at 15% humidity!
Shouldn’t be difficult to get a good static charge for good powder adherence! memtb


You should not use a rifle that will kill an animal when everything goes right; you should use one that will do the job when everything goes wrong." -Bob Hagel

“I’d like to be a good rifleman…..but, I prefer to be a good hunter”! memtb 2024
Joined: Feb 2010
Posts: 608
S
Campfire Regular
Online Content
Campfire Regular
S
Joined: Feb 2010
Posts: 608
They look great.

IC B2

Joined: Jan 2018
Posts: 2,041
H
Hesp Offline OP
Campfire Regular
OP Offline
Campfire Regular
H
Joined: Jan 2018
Posts: 2,041
Did some more casting & PC work today. This is so easy. Why haven't I been doing this before. Today I cast 65gr 25 cal for my 25-20 rifle & 45 cal 330 HP for my 45-70. These bullets shoot great & no leading. The color used is John Deere Green. This green really gives great coverage in one coat. [Linked Image from i.postimg.cc] I am baking longer.400dg for 25 min. No color running . Solid out come. Works perfect.

Last edited by Hesp; 06/12/21.
Joined: Jan 2018
Posts: 2,041
H
Hesp Offline OP
Campfire Regular
OP Offline
Campfire Regular
H
Joined: Jan 2018
Posts: 2,041

Joined: Oct 2008
Posts: 4,196
W
Campfire Tracker
Offline
Campfire Tracker
W
Joined: Oct 2008
Posts: 4,196
Originally Posted by Hesp

Smoke's powder is the best!

Joined: Jan 2018
Posts: 2,041
H
Hesp Offline OP
Campfire Regular
OP Offline
Campfire Regular
H
Joined: Jan 2018
Posts: 2,041
Bullets in plastic container with powder & Air Soft BB's.. Swirl around for about 3 min.[Linked Image from i.postimg.cc]
Bullets on tray ( non stick aluminum Foil ) some standing some laying . Really doesn't make a difference. [Linked Image from i.postimg.cc]
In oven at 400dg for 25 min.[Linked Image from i.postimg.cc]
When done take right out of oven & dump onto a cooling tray lined with non stick foil. Swirl around lightly for a few seconds so bullets don't stick together. You will feel when they don;t stick.[Linked Image from i.postimg.cc]
That's it. Let them cool & cure over night. Size & load. Easy.

Last edited by Hesp; 06/14/21.
Joined: Jan 2018
Posts: 2,041
H
Hesp Offline OP
Campfire Regular
OP Offline
Campfire Regular
H
Joined: Jan 2018
Posts: 2,041
Forgot to mention.Do not handle the freshly coated bullets with bare hands . This will cause the coating to come off. Wear the thin "blue" ( not white ) latex gloves. They work differently. The blue gloves will not allow powder to come off of the bullets before baking. You can also use needle nose pliers if you don;t have the blue latex gloves handy.

IC B3

Joined: Jan 2018
Posts: 2,041
H
Hesp Offline OP
Campfire Regular
OP Offline
Campfire Regular
H
Joined: Jan 2018
Posts: 2,041
Got some bullets cast & coated today for my 38-55. These are cast from an LBT mold. Size is .380 dia , 260gr with Gas Check. Hoping to get a solid 1600 fps & accuracy. Color is clear with some OD Green thrown in for contrast. Tomorrow , hopefully will be inspiring.. [Linked Image from i.postimg.cc]

Joined: Sep 2005
Posts: 4,274
G
Campfire Tracker
Online Content
Campfire Tracker
G
Joined: Sep 2005
Posts: 4,274
Originally Posted by Hesp
Got some bullets cast & coated today for my 38-55. These are cast from an LBT mold. Size is .380 dia , 260gr with Gas Check. Hoping to get a solid 1600 fps & accuracy. Color is clear with some OD Green thrown in for contrast. Tomorrow , hopefully will be inspiring.. [Linked Image from i.postimg.cc]



I have a 20" Uberti 1894 in 38-55 arriving in a few weeks. I sent Verl an email days ago and knowing Verl, it will days.....or longer....before he replies. I LOVE LBT molds/bullets. How have your 260's w/ GC been for you? What metal mix? Accuracy? Which GC's?

Thanks,

Alan

Joined: May 2004
Posts: 55,886
Campfire Kahuna
Offline
Campfire Kahuna
Joined: May 2004
Posts: 55,886
If'n you powder coaters are gonna do it, please do it properly.

[Linked Image from i.imgur.com]


Best Wishes,

DD


I am..........disturbed.

Concerning the difference between man and the jackass: some observers hold that there isn't any. But this wrongs the jackass. -Twain


Joined: Apr 2011
Posts: 68,915
Campfire Kahuna
Offline
Campfire Kahuna
Joined: Apr 2011
Posts: 68,915
Originally Posted by DigitalDan
If'n you powder coaters are gonna do it, please do it properly.

[Linked Image from i.imgur.com]


Best Wishes,

DD


That’s cool DD !


"Allways speak the truth and you will never have to remember what you said before..." Sam Houston
Texans, "We say Grace, We Say Mam, If You Don't Like it, We Don't Give a Damn!"

~Molɔ̀ːn Labé Skýla~
Joined: Jan 2018
Posts: 2,041
H
Hesp Offline OP
Campfire Regular
OP Offline
Campfire Regular
H
Joined: Jan 2018
Posts: 2,041
Originally Posted by GSSP
Originally Posted by Hesp
Got some bullets cast & coated today for my 38-55. These are cast from an LBT mold. Size is .380 dia , 260gr with Gas Check. Hoping to get a solid 1600 fps & accuracy. Color is clear with some OD Green thrown in for contrast. Tomorrow , hopefully will be inspiring.. [Linked Image from i.postimg.cc]



I have a 20" Uberti 1894 in 38-55 arriving in a few weeks. I sent Verl an email days ago and knowing Verl, it will days.....or longer....before he replies. I LOVE LBT molds/bullets. How have your 260's w/ GC been for you? What metal mix? Accuracy? Which GC's?

Thanks,

Alan

The LBT 260gr are cast from scrap WW at 10.5 BHN. I worked up a load using IMR 4198 for 1605 fps. This mold was made for my Marlin rifle. I sent in a lead cast of the chamber/throat area. Mold was cut to match. Using Dacron to hold the powder in place, accuracy is excellent. Holding the powder firmly in place provides great uniformity which contributes to good accuracy. GC are Hornady.

Joined: Aug 2003
Posts: 496
Campfire Member
Offline
Campfire Member
Joined: Aug 2003
Posts: 496
Question regarding the gas checks, Do you need them below 2000fps?
Thanks,
Jerod


(1*)

Aim Small Miss Small



Joined: Jan 2022
Posts: 420
4
Campfire Member
Offline
Campfire Member
4
Joined: Jan 2022
Posts: 420
Originally Posted by Navigator
Question regarding the gas checks, Do you need them below 2000fps?
Thanks,
Jerod


I don’t think so but I can’t say when you do need them. I’ve been shooting un checked rifle bullets in 45-70, 450BM (bolt gun), 308 and 222 and have yet to see any leading at all. Also have shot a lot of them in pistols too, 38 special, 9mm (glock 17) 44 Magnum (pistol and rifle), 40 S&W, 10mm and 45 auto. Again, zero leading in any of them.

The only loads I’ve fired over 2000 fps were in the 450BM and those bullets were gas checked but just because that’s the bullet that’s been the most accurate. Same bullet for my “plinking” load too.

Joined: Mar 2018
Posts: 1,008
G
Campfire Regular
Offline
Campfire Regular
G
Joined: Mar 2018
Posts: 1,008
Originally Posted by Navigator
Question regarding the gas checks, Do you need them below 2000fps?
Thanks,
Jerod

Mike Venturino says gas-checked cast bullets are usually if not always more accurate than plain based cast at any speeds. I prefer to use gas checks when possible even for the 38 special. No they may not be absolutely necessary but I've got better accuracy and a cleaner barrel with them installed. In the 45-70 I can get good accuracy with lyman # 457193 405gr to about 1600fps or so and then things start going south, but it's a microgroove marlin. Gas-checked cast bullets could no doubt be ran faster. In the 308 win I can run gas-checked bullets at 2750fps no problems.

Joined: Jan 2022
Posts: 420
4
Campfire Member
Offline
Campfire Member
4
Joined: Jan 2022
Posts: 420
Originally Posted by Gaschekt
Originally Posted by Navigator
Question regarding the gas checks, Do you need them below 2000fps?
Thanks,
Jerod

Mike Venturino says gas-checked cast bullets are usually if not always more accurate than plain based cast at any speeds.


This has been true in my testing. Shooting the same bullet checked and unchecked the checked bullets always shoot tighter groups. It’s especially obvious in the 450bm. The bullet it likes is the a Lee 452-230-TC bullet that is not designed for a gas check but it has a beveled base. Just for kicks one day I tried to see if a gas check would stay on it and it does, very nicely. So I loaded some up in the 450bm and ran some tests. The unchecked bullet shot better than 4 other bullets but the checked outshot the unchecked by a pretty good margin. It’s the only 45 bullet I cast that will accept a gc so it may not be the best but it’s the best I have.

Joined: Jan 2022
Posts: 420
4
Campfire Member
Offline
Campfire Member
4
Joined: Jan 2022
Posts: 420
Originally Posted by Hesp
Did some more casting & PC work today. This is so easy. Why haven't I been doing this before. Today I cast 65gr 25 cal for my 25-20 rifle & 45 cal 330 HP for my 45-70. These bullets shoot great & no leading. The color used is John Deere Green. This green really gives great coverage in one coat. [Linked Image from i.postimg.cc] I am baking longer.400dg for 25 min. No color running . Solid out come. Works perfect.


Yeah, I just started "painting" bullets a couple of years ago. Every time I reload and shoot I think about the old days of sticky hands while loading and all the smoke shooting them. I shot 308, 350 legend and 44 mag today (all rifles). No smoke and no leading!

Page 1 of 2 1 2

Moderated by  RickBin 

Link Copied to Clipboard
YB23

Who's Online Now
661 members (17CalFan, 10gaugemag, 1beaver_shooter, 1minute, 10ring1, 12308300, 75 invisible), 2,740 guests, and 1,329 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums81
Topics1,187,640
Posts18,399,000
Members73,817
Most Online11,491
Jul 7th, 2023


 







Fish & Game Departments | Solunar Tables | Mission Statement | Privacy Policy | Contact Us | DMCA
Hunting | Fishing | Camping | Backpacking | Reloading | Campfire Forums | Gear Shop
Copyright © 2000-2024 24hourcampfire.com, Inc. All Rights Reserved.
Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.3.33 Page Time: 0.115s Queries: 15 (0.005s) Memory: 0.9008 MB (Peak: 1.0555 MB) Data Comp: Zlib Server Time: 2024-03-28 17:27:18 UTC
Valid HTML 5 and Valid CSS