24hourcampfire.com
24hourcampfire.com
Previous Thread
Next Thread
Print Thread
Hop To
Joined: Feb 2010
Posts: 1,057
W
wbyfan1 Online Content OP
Campfire Regular
OP Online Content
Campfire Regular
W
Joined: Feb 2010
Posts: 1,057
Does anyone know what the twist rate of a Remington Model 700 in 6mm Rem is/or should be?

Thanks.

BP-B6

Joined: Aug 2010
Posts: 47,713
B
Campfire 'Bwana
Offline
Campfire 'Bwana
B
Joined: Aug 2010
Posts: 47,713
It "should" be a 1 in 9" twist rate if it is stamped "6mm rem" on the barrel. If it says 244 remington, it should be 1 in 12" twist.


Originally Posted by raybass
I try to stick with the basics, they do so well. Nothing fancy mind you, just plain jane will get it done with style.
Originally Posted by Pharmseller
You want to see an animal drop right now? Shoot him in the ear hole.

BSA MAGA
Joined: Jul 2005
Posts: 12,492
R
Campfire Outfitter
Online Content
Campfire Outfitter
R
Joined: Jul 2005
Posts: 12,492
Supposed to be a 1-9".


You can roll a turd in peanuts, dip it in chocolate, and it still ain't no damn Baby Ruth.
Joined: Feb 2006
Posts: 2,483
Campfire Regular
Offline
Campfire Regular
Joined: Feb 2006
Posts: 2,483
The older 6mm rem were originally marked as "244 Remington" on the barrel rather than "6mm Remington".
These older guns had a 1-12" twist rate and most(not all) would not stabilize anything much heavier than about 90grs in bullet weight with the types of bullets then available.
That is one of the major reasons the 243 winchester got out of the starting gates quicker than the 6mm Rem.
Winchester saw the 243 as a dual purpose varmit/hunting cartridge and Remington (in their marketing wisdom) saw the 6mm as primarily a varmit cartridge that would be used occasionally as a hunting round - So they twisted it at 1-12" to shoot lighter bullets the best.
Later Remington saw it's mistake and renamed the cartridge "6mm Remington", marked it's barrels as such and started twisting the barrels at 1-9" to compensate (or over compensate, given the 243 W only had a 1-10" from the start).
They twist some of them differently these days to allow for heavier/longer bullets (such as VLD target type and copper).

Your rifle from that time period (mid-70s) most likely has the 1-9" twist, but could be different(like a 1-10").

You can check it yourself to be sure if you'd like to:

1.Take a cleaning rod and install a cleaning patch that fits tight enough to turn the cleaning rod.

2.Insert rod w/patch in the end of your barrel (either end will work, but on a bolt action your can pull the bolt and insert from the receiver to protect the barrel crown)and push until you see the rod start to turn.

3.Take a marking pen and make a mark across the cleaning rod where it is at the edge of the barrel or receiver. Then make another reference mark on top of the cleaning rod near the handle.

4.Push the rod in slowly and carefully watch for the reference mark on top of the rod near the handle to make a full revolution and come back to where it was when you started (one full turn on the rod).

5.Make another mark across the rod where it contacts the barrel or receiver.You now have two cross marks on the rod that it took one full turn to get to.

6.Pull the rod back out, take a tape measure and measure the distance between the two cross marks on the cleaning rod. If it measures closest to 10" you have a 1-10" twist, etc.

To answer another part of you're question: The twist should be for the type of bullets you intend to shoot, but with factory barrels you are limited to what they sell you.
Most people go with at least a 1-9" to shoot the 105gr VLD type bullets for example.


Good Luck,
Ted

Joined: Feb 2010
Posts: 1,057
W
wbyfan1 Online Content OP
Campfire Regular
OP Online Content
Campfire Regular
W
Joined: Feb 2010
Posts: 1,057
Great info guy's. Thanks! I'm going to reload for a friend who has a Rem 700, 6mm. He want's to shoot 55 grain bullet's. I figured this could be an issue dependant on twist rate. I've never really heard of folks raving about accuracy with 55's from their 6mm/243's. Sounds like 80gr plus bullet's might be a better alternative. These loads will be used for general varmit hunting.

IC B2

Joined: Mar 2007
Posts: 1,402
T
Campfire Regular
Offline
Campfire Regular
T
Joined: Mar 2007
Posts: 1,402
I load 55 gr. Nosler BT's in a Rem 700 and get great accuracy. Two powders I have found for these loads are IMR4895 and Varget.


Moderated by  RickBin 

Link Copied to Clipboard
YB23

Who's Online Now
697 members (10Glocks, 10gaugemag, 06hunter59, 222Sako, 222ND, 16penny, 74 invisible), 2,772 guests, and 1,317 robots.
Key: Admin, Global Mod, Mod
Forum Statistics
Forums81
Topics1,187,627
Posts18,398,735
Members73,817
Most Online11,491
Jul 7th, 2023


 







Fish & Game Departments | Solunar Tables | Mission Statement | Privacy Policy | Contact Us | DMCA
Hunting | Fishing | Camping | Backpacking | Reloading | Campfire Forums | Gear Shop
Copyright © 2000-2024 24hourcampfire.com, Inc. All Rights Reserved.
Powered by UBB.threads™ PHP Forum Software 7.7.5
(Release build 20201027)
Responsive Width:

PHP: 7.3.33 Page Time: 0.169s Queries: 14 (0.003s) Memory: 0.8134 MB (Peak: 0.8790 MB) Data Comp: Zlib Server Time: 2024-03-28 16:03:00 UTC
Valid HTML 5 and Valid CSS