I have for sale a custom rifle built on an excellent Sako L61R Magnum action. This is the highly desirable pre-Garcia, Magnum action, imported by Firearms International Corp, and has three locking lugs � two on the front of the bolt and one towards the rear of the bolt. This was a project rifle that wasn't quite completely finished by the original owner. The action appears new and the rifle is unfired.

The 26" barrel is a Douglas Premium Quality Stainless Steel chambered by Douglas in 6.5mm x 300 Weatherby Magnum (6.5-300 Wby.) and measures close to the Douglas #5 Contour. The rifling is 6-groove, 1 in 8" right-hand twist. The barrel is at least 12 to 15 years old, made when Douglas was still one of the top quality barrel manufacturers in this country. I bought the rifle from the original owner's estate around 12 years ago and his widow told me at the time that she thought her husband sent the action to Douglas to have the barrel mounted. She knew quite a bit of other accurate info about the rifle, so I believe she is probably correct.

The stock is nicely figured walnut by Bishop, but is not fully complete. The action and barrel were glass bedded by the owner, but it is not a professional quality job. It could be usable as is, however, if I were to keep the rifle, I would remove around 1/8" to 3/16" more wood from the bottom of the stock around the floorplate/trigger guard and neaten up the bedding and wood-to-metal fit around the receiver and bolt handle cutout.

There is no fore-end tip, and it either needs to be finished out or needs a tip installed. The stock finish was not very skillfully applied, and I don't know what material the finish is, but acetone will cut it. If I kept the rifle, I would strip or sand off all of the finish and refinish it with hand-rubbed tung oil. The stock has plenty enough "meat" in it to take quite a bit of reshaping/re-contouring or slimming down.

The complete rifle weighs 9 1/2 lbs. There are a set of Redfield style scope bases that come with the rifle. The only blemishes I've found on the Sako action is some flattening of the fine checkering where the rear scope base was installed, a tiny mark on the bolt handle knob, and a rust spot on the outside of the magazine box liner that is hidden inside the stock and can only be seen when the rifle is disassembled. There are a couple of very light handling marks on the barrel, but these can be easily polished out.

The 6.5-300 Wby chambering is the ballistic twin of the 6.5 STW and there is reloading data easily found for it. Dies are available from RCBS (Item #56197) and special order from Forster and Redding. Brass can be produced as easily as running properly lubed 7mm STW brass partially into the 6.5-300 Wby sizing die and then fireforming with a moderate load. The rifle will make a terrific long range or "beanfield" rifle and the barrel is twisted to stabilize the longer and/or heavier hunting or target bullets in the hot 6.5mm caliber.

The price is $700 shipped and insured to your FFL holder.













[img]http://i129.photobucket.com/albums/p226/timebak/Sale%20Items/IMG_2306.jpg[/img]

[img]http://i129.photobucket.com/albums/p226/timebak/Sale%20Items/IMG_2307.jpg[/img]

[img]http://i129.photobucket.com/albums/p226/timebak/Sale%20Items/IMG_2300.jpg[/img]

I would be all over this if I had the money.

Do you have dies or any brass? I assume that 300 Wby brass works as well as the 7mm STW?

you might have to do a step in between going from 30 to 6.5, such as you might need a 7mm sizing die too.

but yes, you can make these 6.5x300 Wby cases out out of 300 Wby cases.

Don't have any dies or brass, sorry. But they're both relatively easy to procure, for a wildcat cartridge.

ttt

free bump for an awesome rifle

Thanks atomiclab! ttt

Noon bump.

bump