|
|
Joined: Mar 2005
Posts: 26,283 Likes: 6
Campfire Ranger
|
Campfire Ranger
Joined: Mar 2005
Posts: 26,283 Likes: 6 |
Interesting this is a 7.3 mm drill bit is .2874 and an L is .29. Plus the fact that you can buy a kit containing the Hornady case gauge tube, 5/16 x 36 tap and L bit as a kit off Amazon. My gauge is a Stoney Point.
I saw that too. Could be my ChiCom tap is the problem!....... My stuff is the early Stoney Point too. My second comparator body is Hornady though. I have calipers dedicated to the two comparator bodies and the "Head' N Shoulders" body.
Last edited by alpinecrick; 11/21/21.
Casey
Not being married to any particular political party sure makes it a lot easier to look at the world more objectively... Having said that, MAGA.
|
|
|
|
Joined: Nov 2008
Posts: 8,673
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2008
Posts: 8,673 |
I use digital calipers. Easier to zero and read for an old man. Can’t remember exactly where I bought the tap but it’s got USA stamped on it and at the time it wasn’t the cheapest. Drill bit I use is an L although 7.3 and 9/32 do work. I never really worried about thread depth due to drill size as when I thought about it, you aren’t really putting enough strain or pressure on it as you would a fastner. As far as the case I also found that a once fired case that would rechamber in that rifle was the easiest. A bullet would already mostly slide in the neck.
Swifty
|
|
|
|
Joined: Oct 2006
Posts: 2,412 Likes: 3
Campfire Regular
|
OP
Campfire Regular
Joined: Oct 2006
Posts: 2,412 Likes: 3 |
HCI (local) had the tapered (plug) tap and bit I needed, though it was the "L" bit I got, not the 7.3mm mentioned. Seemed to work OK though.
To preserve liberty it is essential that the whole body of people always possess arms and be taught alike, especially when young, how to use them.-Richard Henry Lee
Endowment Member NRA, Life Member SAF-GOA, Life-Board Member, West TN Director TFA
|
|
|
|
Joined: Jan 2001
Posts: 14,324
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2001
Posts: 14,324 |
If you use a Wilson trimmer, any good quality drill press vise with a v-notch will hold the case holder for the specific caliber you want to work on in a straight up perpendicular position to drill and tap as many cases as you like with one simple set-up to find center. Once the drill press vise is locked down, make as many of each caliber you want, then just change the holder. Pop the brass out with the blade of a screw driver or chisel. Then just change to holders to make more in another caliber.
Phil
|
|
|
|
Joined: May 2001
Posts: 4,124
Campfire Tracker
|
Campfire Tracker
Joined: May 2001
Posts: 4,124 |
I used a metal lathe 3jaw chuck and a drill chuck in the tailstock to start the taper tap. And finished with a ratchet tap handle. I didn't think a couple of thou would matter in this use. The 8" chuck slipped on a couple of cases, so they got tossed. I did about a dozen.I'm still learning on the metal lathe. I use to do two sticks and a knife.
You can hunt longer with wind at your back
|
|
|
|
565 members (1minute, 1234, 1Longbow, 2500HD, 10Glocks, 1moredeer, 54 invisible),
1,860
guests, and
1,070
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,896
Posts18,498,046
Members73,980
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|