|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
I am going to show the steps in making this bow for my son. This will be a build along sort of thread This bow will be a reflex/deflex Long bow. It is a hybrid combination of a longbow and a recurve. Longbows are typically straight when unstrung and recurves are still curved even when unstrung. This bow will look sort of like a recurve while unstrung and like a longbows when strung. Here is a pic I stole off the web to give you an idea of what I am going for. The woods I am using for Josh's bow are the same ones I use to make knife handles. For the most part, they are South American hardwoods. The riser will be made from Bubinga, Bloodwood and good old American hard rock maple from a tree my Dad cut many years ago. Sort of a legacy piece of wood, cut by my Dad, Made into a bow by me and finally used by my son. I will also use some of the Maple in the limbs. this is the order in which I will stack the layers. Most S.A. hardwoods have oils in them that make gluing difficult, so I use acetone to clean and degrease. Blood wood and purple hear are some of the oiliest. You can see the orange oil in the basin of the sink. It took a long time to clean that sink. I should have sprayed it with pam first. :oops: Once cleaned, I used a hacksaw blade as a scrapper to rough up all the gluing surfaces. Epoxy does not like smooth surfaces. The glue I am using can be purchased at a number of bow building web sites. This is a two part epoxy that gets stronger if cured under a heated condition. This is important because if you leave the bow in a hot car on a sunny day, The glue had better have been cured at a high temp to keep the bow from de-laminating. It mixes like any other epoxy. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow6.jpg[/img] Make sure to cover your work surfaces with wax paper or plastic wrap. It is hard to clean up any spills. Then simply butter both sides of the surfaces to make sure you have no dry spots that will later separate. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow7.jpg[/img] I use spring clamps because C-clams will get loose during the heating process when the glue oozes out. (trust me, there is a lot of oozing) Spring clamps keep a constant pressure at all times. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow8.jpg[/img] I then take the riser and put it in a preheated oven. Bake for 8 hours at 180F until a nice golden brown and serve with a scoop of vanilla ice cream . When it comes time to glue up the bow itself, I will build an oven box that is 6 feet long as the bow will not fit in the oven. I will heat this box with 100 watt light bulbs. Fast forward 8 hours and a few more hours for a slow cool down period and the riser is all glued up. The rubber tips of the clamps need to be pried from the glue. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow92.jpg[/img]
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
Next, I ran the block through my table saw to square it up and remove the excess glue. Then I drew the riser pattern on the wood and cut it out with a band saw and sanded the fade outs on a drum sander. This glue is a flexible epoxy. Normal hardware store epoxy would crack and break if bent like this. Make sure to use only enough glue for the job at hand. A little goes a long way. I now need to make the form that I will use to glue the bow on and I need to make the heat box.
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
Before I can go any futher with Josh's bow, I need to build the form that the bow will be glued together on. There are a lot of ways to go about this and forms can be made many ways but I chose a way that seemed easy to me. I bought a nice straight 2 x 10 and traced the form that I came up with onto the wood. Then cut it out with a jig saw. I then went over the entire length of the curve with a square to make sure there were no twists in the form. Any irregularities were taken out by sanding. In order to keep the form straight over time and in the heat of the oven box, I screwed a few 2x4's along both sides. They will also act as feet to keep the form from tipping over. Next, I covered the entire curve with a piece of 1/8th inch thick by 1 1/2 wide aluminum strip. This will make the the curve a much better surface to build the laminations on and it will be more repeatable should I want to build more bows from this form. This form will build bows up to 70 inches in length. This bow will be a 66 inch model. I need to drill a bunch of clamp holes along the curve for the spring clamps. When I assemble the bow, I plan to use spring clamps to compress all the layers of wood, fiberglass and epoxy together. I drilled big round holes and then used a jig saw to square up the side of the hole closest to the top surface. This will give the clamps a little more room. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow117.jpg[/img] I will use one clamp on each side of the limb. Like this. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow118.jpg[/img] I also got a package in the mail today from Old Master Crafter of Waukegan, IL. I ordered the wood laminations a few days ago and these things showed up a lot faster than I was told they would. (Great Service) It does not look like much for about $60 but what it is, is 6 taper ground action wood strips that are .065" thin on one end that taper at .001" per inch of length. The strips are 36 inches long and 1 1/2 inches wide. they came protected by two nice looking strips of Zebra wood. I will use them for knife handles at a later date. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow119.jpg[/img] [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow120.jpg[/img]
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
I placed the thick end of one piece next to the thin end of another so you can see the taper. Each limb will get three of these tapers and one strip of parallel thickness Hard rock Maple that is from the piece of wood my Father cut so many years ago. This is the same piece of wood that I used in the riser. On the front and back of each limb will be a thin layer of Kingwood and then clear fiberglass. All of this will be assembled with the same epoxy I used to make the riser but first I need to assemble an oven box. I built the oven box for the bow form. I will spare you the details since it's just a box made from scrap plywood that was left over from another project. I will say that It is 12 inches high and 22 inches wide and 74 inches long. By removing 6 screws at each end of the box, I can reduce the box to four individual panels for easy storage. You will also notice that the box has neither a top or bottom. The reason for not having a bottom is so that I can bring the box to the form that will be covered in oozing epoxy and many clamps (creating a challenge to move) I would rather bring the box to the form. With the box complete, I assembled the heat source that I will use to raise the inside temp of the box to 160F. A trip to the Home Depot for the supplies ran me about $30. The first step was to get rid of those pesky warning labels. Nobody reads them any way. The extension cord company knows I am not going to read the label in English so why would they expect me to read it in Spanish? I hope the extension cord labels are not like mattress labels. I would have to spend time behind bars for removing them. Once I cut the extension cord into bits, I wired the light bulb bases together in series so that one plug would power them all. A quick test revealed that I had had paid attention in shop class. I placed the form between the two light bulb boards and brought the box to the form. My Son will need to help with this part as the box is a bit long to handle alone. Everything fits nicely. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow127.jpg[/img] The cover of the box will be an old closet door from our last house. It is hollow so it is light enough to move around and it was free. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow128.jpg[/img] I drilled a hole in the door and inserted the probe of a thermometer. This way, I can keep tabs on the temp inside the box without opening it and letting the heat escape. My wife won't be cooking a turkey for a few months anyway. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow129.jpg[/img] After two hours with the bulbs on, the temp never got above 135F. I will replace the 100 watt bulbs with 150 watt bulbs and add two additional bulbs to the boards [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow130.jpg[/img][/quote] The next test will include covering the oven box with a canvas to trap the heat better. I think 2 extra bulbs should do the trick. The next step will be to make a test bow out of scrap material so I get the feel for the assembly process and so that I can check the glued up trial piece for any warps that I will be able to correct before wrecking a bunch of expensive woods and fiberglass. It is a piece of mind exercise.
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
In order to evaluate the bow form, I built a mock up. I bought a pine, 2 x 6 and cut it into strips that were .065 thick. Before gluing the strips together, I protected the form with two layers of tape. It will be easier to remove and replace the tape then it will be to try and chip away any excess glue from the form. Next, I covered the surfaces of the form with plastic wrap to keep it clean. I used yellow wood glue for the mock up. It did not require the oven box. Once all the layers were covered in glue, I used clamps and strips of rubber inner tube to compress the layers. In the center section (where the riser will be) I added a few extra strips. After 24 hours, I removed the clamps and the plastic wrap. There was no "Spring back" or relaxing of the wood strips. I then took the mock up and reversed it on the form to see if it was symmetrical and it fit the form equally in either orientation. I checked for twists in the limbs and found none. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow137.jpg[/img] [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow138.jpg[/img] I then placed the riser against my chest and grabbed both limb tips and began to flex the bow. Since I did not have any fade outs and the ridged glue does not like to flex (and the pine had many knots) both limbs broke [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow139.jpg[/img] This allowed me to nest the limbs and look for any twists or differences between the two. Everything looked good. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow141.jpg[/img] I think all is ready to assemble Josh's bow. I will want to baby sit the oven box for the 8 hours that it will cook
Last edited by DIYguy; 04/16/14.
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
I insulated the inside of the oven box to make regulating the heat easier. I bought a roll of insulation that is made from a double layer of bubble wrap with heavy duty foil on both faces. It is just under a 1/4 inch thick and lightweight. I used a staple gun to attach it to the inside walls of the box and to the under side of the box cover. I then added two additional light bulb bases to the boards that I had made up earlier. I used 100 watt bulbs in the center two bases so now I have (4) 150 watt bulbs and (2) 100 watt bulbs. After one hours, the temp had risen to my goal temp of 160F. I felt the outside of the box in several locations and could not feel any heat escaping through the walls or lid. After 2 hours, the temp had risen above my goal but I consider this a good thing since I will now be able to crack the lid a bit or perhaps unscrew one bulb to control the temp. The oven box is finished and ready for the big day. I did a dry run and found something I never thought through (Which is the point of a dry run) [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow154.jpg[/img] While the riser fits great on the empty form, adding the strip of fiberglass backing, four tapered laminations and the fiberglass face caused the fade-outs to lit poorly. I did not factor in the tapering of the laminations as they work away from the center of the riser. I discovered a gap at the fade-out area. I felt this gap was larger than it should be and do not want a large amount of epoxy at this hinge point. I might just be over cautious but I want a better fit and a consistent glue line. The dark black area near the thinest part of the riser is what I am worried about. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow156.jpg[/img] I sanded down the riser until it fit better. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow155.jpg[/img] I also made some tillering attachments that will slide on the end of the un-shaped limbs before I taper the sides and make the string groves. they are made from 4large washers that I epoxied together and cut notches in [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow153.jpg[/img]
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
So, enough waiting already. Time to glue this bow up. I laid out everything I needed since the dry run a few days ago. Then I put both quart containers of the epoxy in a basin of hot water to warm them up a bit. Next, I cleaned all the wood and glass surfaces and laid them in the order in which I would glue them. 1. is .050 clear glass 2. is .020 kingwood vernier 3. is .090 thick hard maple taper (two pieces glued together to make one long piece) 4 and 5. is .065 thick hard maple taper (two pieces glued together to make one long piece) 6. is a piece of hard maple .060 parallel from the piece of wood my Dad cut. (two pieces glued together to make one long piece) 7. is .020 kingwood vernier 8. is .050 clear glass Missing from the picture is the riser. Fast forward to a completed glue up with the warmed epoxy. Due to the mess and the fact that I was working alone, I did not slip out of my sticky rubber gloves to take pictures along the way. What a slippery mess to work with. I used a combination of spring clamps and rubber inner tube strips to compress all the layers. I had more C-clamps at the center (on the riser) but I took them off once I realized that they stuck up higher than the sides of the box and the cover would not lay flat. So much for a complete dry run. I should have tried the lid of the box also. Oh well. live and learn. Here is a close up of all the layers and all the extra glue that oozed out. I also learned that I used too much glue. I think I could have built two bows with what came out from between the seams. Once again. Live and learn. Here is the oven box doing it's job of keeping the bow at around 160F. I will unplug it before I go to bed and let it slowly cool down over night.
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
|
|
|
|
Joined: Aug 2012
Posts: 2,436
Campfire Regular
|
Campfire Regular
Joined: Aug 2012
Posts: 2,436 |
Didn't know there could be that many clamps.
|
|
|
|
Joined: Sep 2009
Posts: 13,860
Campfire Outfitter
|
Campfire Outfitter
Joined: Sep 2009
Posts: 13,860 |
|
|
|
|
Joined: Feb 2010
Posts: 615
Campfire Regular
|
Campfire Regular
Joined: Feb 2010
Posts: 615 |
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
It took a solid hour to free the bow from the form. Removing the spring clamps was easy, The epoxy covered strips of inner tube proved to be a bit tougher. The form cleaned up easy because of all the tape I used to protect it. The bow was a little tougher. The extra epoxy was everywhere and held bits of the inner tube captive. To save on a mess in the shop (and because it was a nice day) I took the bow out to the back patio behind my shop. The breeze would blow all that nasty fiberglass dust away. I learned that I need to place a layer of plastic wrap between the last layer of glass and the aluminum pressure strip. I didn't do that with this bow and needed to sand away the excess epoxy to free it from the bow. This also gave me my first look at the glue lines between the layers of wood. after sanding both sides I could pry away the aluminum pressure strip. Then I just had to peel away the tape to see how the Kingwood looked under the clear glass. And the other limb. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow169.jpg[/img] and finally the back of the bow. Everything looked good. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow170.jpg[/img] Then I worked on the riser. there was a lot of epoxy to remove. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow171.jpg[/img] The risers looks good and so do the skive cuts that joined the strips of maple [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow173.jpg[/img]
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
I used my belt sander with a 50 grit belt to grind down the limbs to the lines I scribed. Next, I marked the location of the string grooves in the ends of the limbs. Using a chainsaw file I made the beginnings of the string grooves. This will help me locate the tip overlays. when they are installed, I can finish the grooves. For the overlays, I want to use Bloodwood and antler. The Bloodwood will match the accent strip in the riser and the antler is just something I wanted to try. I had a section of antler left over from a knife handle I made. I will use the longest tine as it has no pithy core. It is solid all the way through. Using the belt sander, I created a flat spot on the antler that will run against the rip fence of my table saw. I am using a carbide tipped finish blade so I get less chipping and a smooth cut. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow191.jpg[/img] I made the strips about an 1/8th of an inch thick. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow192.jpg[/img] In order to get the best adhesion with the epoxy, I needed to rough up the shiny surface of the clear glass. I used a hacksaw blade as a scraper. I did the same to the bloodwood and the antler. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/joshbow193.jpg[/img]
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
I got the string for this bow. It even matches the colors of the riser. Before I could use the new string, I needed to build a tillering tree to check the limbs for even bending. I had a section of treated 2x4 up in the rafters of my garage for a few years so I knew it was good and dry. I drilled a series of 3/4" diameter holes at a 15 degree angle in the edge of the 2x4. The holes are 2 1/2 inches deep. In those holes, I glued short sections of 3/4 inch wooden dowels. I then sanded them to round off any sharp edges. And marked off the distances along the side. This is the bow holding end of the tree. I use a piece of leather to protect the riser when I clamp the bow in place. I attached a plywood base so it would stand by itself. With the string grooves filed and the tillering tree finished, I strung the bow for the first time. and drew it back. It was a good feeling. I then put it in the tree and drew the bow to a few different lengths to see if the limbs were flexing equally. Here are the pics. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/tree6.jpg[/img] [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/tree7.jpg[/img] I can see some differences in the flex of the limbs. I will sand away certain areas to make the limbs act the same. Lessons learned. I could have left out every other wooden peg. I really don't need one at every inch.
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
After stringing the bow and having Josh draw it a few times, I asked him how the grip felt. He didn't like the bump in the center of his palm so I sanded it down a bit more and did all the finish sanding of the rest of the grip. While I was hand sanding, I looked up to see 3 young gals heading up the driveway to visit. I stopped sanding and grabbed the camera. They didn't hang around long after I told them what I was making. With the sanding done (320 grit) I masked off the riser leaving the bloodwood exposed. I cleaned it with denatured alcohol in preparation for sealing the oily bloodwood with super glue. I squeezed a line of glue on the wood and worked it in with my index finger using a circular motion and made sure not to stop long enough to become fused to the bow. The Super glue gives a nice shiny acrylic finish and seals and files the pores. After a 20 min. dry time, I peeled the tape and used 320 and the 400 grit sandpaper (including the glass) to take off the shine and smooth out the glue. The bloodwood is now sealed and now will accept the finish and dry at the same rate as the rest of the woods in the riser. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/grip6.jpg[/img] [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/grip7.jpg[/img]
|
|
|
|
Joined: Jan 2014
Posts: 1,298
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2014
Posts: 1,298 |
I wanted to add a medal to the bow's riser and I used a hat/lapel pin that I got at the last Wisconsin Bowhunter's Annual convention. Being that I was a Director for the WBH, I though it would be a nice touch. I drilled a shallow hole for the medal so that it would sit below the surface of the riser. It was a good fit. I then masked off the riser and cut away the tape covering the hole. I used two layers of tape so that when I used a putty knife to level the epoxy, It would sit just higher than the riser and allow me material to sand away to make flush. When the epoxy cured, I sanded it so the epoxy was level with the wood. I kept on sanding until I had the whole bow smooth with 320 grit sandpaper. I then cleaned the bow with a tack rag and then wiped it down with denatured alcohol. I masked off the glass because I want to finish the riser with tung oil. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/finish2.jpg[/img] I applied the Tung oil using the same "Brush" I used to apply the super glue to the bloodwood. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/finish3.jpg[/img] I rubbed in a healthy dose of the tung oil and after it cures, I will give it two more coats. I will then use 400 grit and steel wool to smooth out any lines and give it two more coats. [img] http://i28.photobucket.com/albums/c239/212007154/josh%20bow/finish4.jpg[/img]
|
|
|
|
78 members (338rcm, 7mm_Loco, 35, 6mmbrfan, 1_deuce, 10 invisible),
1,413
guests, and
816
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,193,450
Posts18,507,949
Members74,002
|
Most Online11,491 Jul 7th, 2023
|
|
|
|