|
Joined: Dec 2011
Posts: 1,697
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2011
Posts: 1,697 |
If you set your resizing die to the rcbs instructions should there be any headspace issues. I don't have a headspace gauge and am new to reloading
Tater
|
|
|
|
Joined: Jun 2004
Posts: 44,933 Likes: 23
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,933 Likes: 23 |
Probably no major issues, but likely you'll be sizing your brass more than necessary.
|
|
|
|
Joined: Dec 2011
Posts: 1,697
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2011
Posts: 1,697 |
That a bad thing? I mean what should one do
Tater
|
|
|
|
Joined: Jun 2004
Posts: 44,933 Likes: 23
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,933 Likes: 23 |
It may be more than what you want at this point, but here's an old post of mine: I'm at work and it's getting busy, so I'll add to this post in small pieces as I can.
First let's assume, and yes I know what that can get us \:D , that the dimensions of the chamber and sizing die are within the normal range and there are no pathological brass problems. Furthermore since I'm primarily addressing the original poster who is new to the game I'll avoid mentioning measurement tools a real beginner may not yet have on his bench.
The main idea is to size the brass just enough to chamber the way we want while not excessively moving the brass around. We'll be working with brass that has been fired in the same chamber it's headed for now. We'll be full length sizing, but barely enough.
Remove the expander ball assembly from the die. When we're doing the initial adjustments we'll be passing a single piece of brass through the sizing process a number of times. We're trying to get the body and shoulder of the case sized the correct amount and while this is getting ironed out there's no reason to size the neck down and run it over the expander ball a bunch of times.
With the proper shellholder installed in the press ram, lower the handle so the ram is in its highest position. Thread the die into the press until it touches the shellholder, and then back it out a turn.
Clean a case really well with a piece of steel wool, paying particular attention to the neck and shoulder areas. Wipe it down with alcohol and after it dries color the neck and shoulder area with a permanent marker. After the ink dries size the case.
More than likely when you examine the case you'll see the ink disturbed part of the way down the neck while the ink on the shoulder is undisturbed. We're going for getting nearly all of the neck sized without messing up the shoulder. The shoulder is going to get bumped eventually, but not too much.
Just to check, wipe the lube off the case and see if it smoothly chambers in the rifle. At this point it should.
Turn the die in 1/6 turn, re-lube and size the brass. Check out how far down the neck is getting sized. Is it close to all the way? Is the ink on the shoulder being touched by the die? Does the case still chamber without resistance?
As this process is repeated 1/6 turn at a time you'll most likely reach a point where nearly all of the case neck is sized, the die still hasn't disturbed the ink on the shoulder, but when you try to chamber the brass the bolt won't close on the sized case without significant resistance, or maybe it won't close at all. After the extracting the brass from the gun you'll see the chamber has disturbed the ink on the case shoulder.
This is the critical zone. The die has squeezed the body of the brass below the shoulder, and this has caused the length of the case from the head to the shoulder to increase. Yes, increase. Remember when you checked the shoulder ink after sizing it hadn't been disturbed by the die. What we want to do is size the case a little more, just enough to eliminate the chambering difficulty.
Clean and re-ink the case. Screw the die into the press another 1/12 turn and size the case. Has the shoulder ink been disturbed by the die?
Yes: Try the case in the chamber. If it chambers with just a little "feel" upon closing the bolt you're almost done.
No: Turn the die in another 1/12 turn and repeat.
So now you've sized and resized this piece of brass so it chambers with a small bit of resistance when you close the bolt. Sounds good, right? Well almost.
You see, a piece of brass that hasn't been through the die as many times as this one will not size down quite as much in one pass. So the die will probably need to go into the press a little bit more for perfection, say 1/24 turn. Give it that final little adjustment.
Install the expander ball assembly back in the die. Lube a different case, including the inside of the neck, and run it through the sizer. Wipe it off and try it for fit in the rifle. If the bolt closes with little or no resistance you're golden.
This procedure is one of those things that's harder to describe than it is to demonstrate. If someone who knows the ropes was there with you they could have you up and running inside five or ten minutes. Once you learn how your sizing die and rifle chamber interact with your particular lot of brass you can set up the die without having to jump through these hoops again.
mathman
|
|
|
|
Joined: Mar 2013
Posts: 859
Campfire Regular
|
Campfire Regular
Joined: Mar 2013
Posts: 859 |
mathman's instructions are spot on. Only problem with this method is brass won't always be interchangeable between guns. Which isn't really a big deal, just pick up another set of dies in the classifieds if you have more than one gun in that cartridge.
|
|
|
|
Joined: Dec 2011
Posts: 1,697
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2011
Posts: 1,697 |
I resized some brass and they chamber but I followed the directions in the rcbs full length sizing die paper
Tater
|
|
|
|
Joined: Jun 2004
Posts: 44,933 Likes: 23
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,933 Likes: 23 |
More dies aren't necessary. Just put reference marks on the die and press, then adjust to those marks.
|
|
|
|
Joined: Jun 2004
Posts: 44,933 Likes: 23
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,933 Likes: 23 |
I resized some brass and they chamber but I followed the directions in the rcbs full length sizing die paper You didn't ruin anything, you just don't need to size them down that much next time. Remember the instructions provided with the die are generic. They are written so following them will allow any piece of brass sized in that manner to smoothly enter even a SAAMI minimum dimension chamber.
|
|
|
|
Joined: Dec 2011
Posts: 1,697
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2011
Posts: 1,697 |
Is there a way to measure with calipers to see if I am in spec
Tater
|
|
|
|
Joined: Jun 2004
Posts: 44,933 Likes: 23
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,933 Likes: 23 |
They're all sort of indirect methods. Right now I wouldn't sweat it.
|
|
|
|
Joined: Dec 2011
Posts: 1,697
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2011
Posts: 1,697 |
Ok just didn't know if I done something wrong by the rcbs directions
Tater
|
|
|
|
Joined: Jun 2004
Posts: 44,933 Likes: 23
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,933 Likes: 23 |
Hordes of people load millions of rounds according to the generic directions, and they do fine.
We're enthusiasts here at the 'fire, so we strive to tune and tweak things for best fit, best performance and so on. Ask questions, a bunch of us like talking/typing about handloading principles and techniques.
|
|
|
|
Joined: Dec 2004
Posts: 5,126 Likes: 1
Campfire Tracker
|
Campfire Tracker
Joined: Dec 2004
Posts: 5,126 Likes: 1 |
I resize in a process similar to mathman's above. I full length size all brass to just smaller than a crush fit in the gun it is to be used in. This will allow you to get a lot of firings. I have some factory chambers that have gotten 17 firings and still counting with this method. One of my guns will only allow 5 or so firings depending on the load before the brass starts showing signs of getting tired.
"Is there a way to measure with calipers to see if I am in spec" The spec you need to meets is your guns chamber. jmho Tim
"The significant problems we face cannot be solved at the same level of thinking we were at when we created them." Albert Einstein
At Khe Sanh a sign read "For those who fight for it, life has a flavor the protected never knew".
|
|
|
|
Joined: Dec 2011
Posts: 1,697
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2011
Posts: 1,697 |
I always ask questions here some probably are stupid but I don't have anyone to teach me so I'm learning on my own and books and from here. I appreciate all the advice.
Tater
|
|
|
|
Joined: Jun 2011
Posts: 10,965 Likes: 74
Campfire Outfitter
|
Campfire Outfitter
Joined: Jun 2011
Posts: 10,965 Likes: 74 |
If you don't have a head space gauge, it won't matter. The "crush fit" method can fool you unless you remove the firing pin and spring to feel the actual crush fit and not the resistence of the spring.
A great way to set your dies was taught to me by a loading mentor; use a socket from your tool box.
Pick a socket that will contact the case's shoulder somewhere in the middle when placed over the neck. Measure with your calipers from the case head to the end of the socket while it is on the case making contact with the "datum".
Do this first with a piece of brass that has been fired in your chamber. Set your die so that the shoulder has been bumped .002" . Simply size the brass and measure with the socket on top. Continue screwing the die into the press in small increments until you read .002" less than the fire formed brass....
The people wringing their hands over Trump's rhetoric don't know what time it is in America.
|
|
|
|
Joined: Jun 2004
Posts: 44,933 Likes: 23
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,933 Likes: 23 |
I use a fancy "40 gauge" that way for 308 class cartridges. It's a deprimed and sized piece of 40 S&W brass.
|
|
|
|
Joined: Aug 2011
Posts: 6,519
Campfire Tracker
|
Campfire Tracker
Joined: Aug 2011
Posts: 6,519 |
Yep, I have several pcs of handgun brass on the shelf for that very purpose. By the way Mathman, that is a very good and clear explanation you gave for partial full length resizing. Thanks.
If we live long enough, we all have regrets. But the ones that nag at us the most are the ones in which we know we had a choice.
Doug
|
|
|
|
Joined: Dec 2011
Posts: 1,697
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2011
Posts: 1,697 |
Bea175 thanks I watched some videos on those they look like they work pretty good thanks
Tater
|
|
|
|
Joined: Aug 2013
Posts: 205
Campfire Member
|
Campfire Member
Joined: Aug 2013
Posts: 205 |
Buy a hornady headspace gauge set. Best 30 bucks you can spend. Takes all the guess work out of resizing.
|
|
|
|
612 members (10gaugeman, 10gaugemag, 1100mag, 01Foreman400, 12344mag, 60 invisible),
19,073
guests, and
1,352
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,194,979
Posts18,539,980
Members74,052
|
Most Online21,014 8 minutes ago
|
|
|
|