|
|
Joined: Mar 2011
Posts: 83
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2011
Posts: 83 |
I took my Glock 30 to the range this weekend and for the first time ran some of my Hornady XTP reloads through said gun. Out of the 20 reloads used, the slide failed to return all the way to the forward position on close to 50% of the shots. It stopped between 1/8" and 1/4" of returning to its original position and it took a quick pop with the palm of my hand to finish the action. I have fired 3 boxes of factory hardball ammo through it without a problem and I hand load for another Glock so I am not a total novice to the craft. My COAL is right on the money and the powder amount is a little under book max. Any suggestions to help remedy this problem would be greatly appreciated. Thanks.
Brett
|
|
|
|
Joined: Oct 2005
Posts: 16,000
Campfire Ranger
|
Campfire Ranger
Joined: Oct 2005
Posts: 16,000 |
suspect you have the O.A.L. over all length maybe a tad too long. I would take the barrel out of the unloaded pistol, and try one of your reloads in the barrel and see how it lines up. I had a similar problem using a coal out of a reloading book and for the particular pistol it was just a little too long. The H&G 68 type 200swc if seated out just a little too far will do that. I would also make darn sure the glock is clean and lead/etc is not building up.
THE BIRTH PLACE OF GERONIMO
|
|
|
|
Joined: Mar 2011
Posts: 83
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2011
Posts: 83 |
I will try the shorter COAL. Thanks
|
|
|
|
Joined: Oct 2004
Posts: 24,661
Campfire Ranger
|
Campfire Ranger
Joined: Oct 2004
Posts: 24,661 |
Also check your taper crimp. Mic the mouth of the case on a loaded factory round that works well in your gun, then adjust your taper crimp die to match. I used to know the ideal dimension off the top of my head, but I had more brain cells back then�for some reason .471 comes to mind, but don�t trust that; go with the measurement on the factory round.
|
|
|
|
Joined: Mar 2011
Posts: 721
Campfire Regular
|
Campfire Regular
Joined: Mar 2011
Posts: 721 |
I have a Glock 30 with a KKM barrel in it and love the darn thing. The above recommendations seem to be spot on. OAL can be the stopper in a lot of reloads as can any bulges in the case.
I have a LEE factory crimp die in .40 and .45ACP that I take the top of the die off and use a casting pusher from Lee and push the loaded rounds all the way through and out the top of the FCD. That die has a carbide sizing ring in the bottom of it and pushing a completed round through it will smooth out any bumps and bulges in the case.
There are UTube videos on this process.
|
|
|
|
Joined: Jan 2007
Posts: 11,517
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2007
Posts: 11,517 |
remove the barrel from your pistol , as you make loads drop them in the chamber and make sure they drop freely in the chamber all the way , you will than learn if it is a coal problem or crip not tight enough
|
|
|
|
Joined: Jul 2010
Posts: 9,517
Campfire Outfitter
|
Campfire Outfitter
Joined: Jul 2010
Posts: 9,517 |
use a bulge buster on your sized cases.
"wanna hear God laugh? Tell Him you have complete control now!"
|
|
|
|
Joined: Mar 2011
Posts: 83
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2011
Posts: 83 |
Thanks for the suggestions gentlemen. I will give them a try.
Brett
|
|
|
|
512 members (10gaugemag, 10ring1, 11point, 16penny, 10gaugeman, 160user, 62 invisible),
2,769
guests, and
1,301
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,191,385
Posts18,469,625
Members73,931
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|