I have the four painted stocks shown below for sale. They're made by a Texas based company and are 84M prototypes. They have considerably more carbon fiber in them than the Costa Rica made stocks, and unlike the current Montana stocks don't consist of a thin shell over a two-part polyurethane expanding foam core. The forend is filled with a low density solild material so the barrel channel can be opened up significantly to accommodate a heavier profile (see t-nut counterbore holes). In addition, the forend has two sling swivel studs that are mounted using t-nuts so significantly stronger than the Costa Rica model. The rear stud is mounted into a block of aluminum that is locked into the inner butt geometry which is also much stronger than the Costa Rica made stock. Another salient feature is the spring stop at the front of the magazine well that prevents the lower spring leg from kicking forward which typically causes the rear of the follower to drop and the bolt to ride over the top round in the magazine. The stocks are close in weight to the Montana stock and I can provide actual weights if desired.

* More barrel channel clearance than current Montana stocks
* Solid forened to accommodate heavier barrel profiles
* Two sling swivel studs in forened screwed into t-nuts
* Spring stop in magazine well
* Very tight recoil lug pocket for a no-bed option
* Rear sling swivel stud screwed into solid aluminum block
* Sherwin Williams painted exterior
* Similar weight to current Montana stock

Price as shown: $275 + $25 shipping
Price with inletting 95% complete: $300 + $25 shipping

These stocks are intentionally made to minimal dimenisons so a barreled action will be very tight. They will almost certainly require the paint to be removed from all mating surfaces, and possibly some material from the recoil lug pocket and the receiver mating surfaces. You most likely won't need to do any bedding with these stocks but you always have the option.

Thanks for looking and first come, first served.

Are these short action or long action ?

84M which is the short action.

I am on the fence! Want but don't need!

I’ll take the bottom one

Can you please show a close up of the surface texture?

Here are some close-up images that hopefully show the surface texture. They're shown in the same order as the stocks above i.e. 2nd through 5th.

Sealskin





Well Bred Brown





Smokehouse





Iron Ore

To avoid any confusion, the forends are filled with a low density solid material i.e. can be opened up without issue. As far as I know, the buttstock is not filled with the same low density solid material. It's my understanding that a low density foam is injected into the buttstock region before the recoil pad is glued in place.

Here are actual weights for each of the availalbe stocks.

Seal Skin: 24.4 oz

Well Bred Brown: 25.4 oz

Smokehouse: 28.8 oz

Iron Ore: 30.0 oz

I’ll take the seal skin in the 95% inlet condition for $325 shipped.
PM the details....

Daveh, PM on the way. The Seal Skin is my favorite color by the way, and I was seriously thinking of keeping that one but it's yours.

pabucktail, the Iron Ore stock is yours assuming you still want it. PM has been sent.

Here's the current status, pending funds of course.

Seal Skin: SOLD to Daveh

Well Bred Brown: Available

Smokehouse: Available

Iron Ore: SOLD to pabucktail

I'll take the brown with 95% inletting. PM inbound.

adkshootr, thanks very much!

Seal Skin: SOLD to Daveh

Well Bred Brown: SOLD to adkshootr

Smokehouse: Available

Iron Ore: SOLD to pabucktail

Update.

Seal Skin: SOLD to Daveh

Well Bred Brown: SOLD to adkshootr

Smokehouse: Available

Iron Ore: Available

Damn.
Seconds on the sealskin (although it won’t be needed.)
Do you have any coming up for the 84L?

Sorry ... no 84L models. The Iron Ore is available now.

I'll take the Iron Ore with 95% inletting, $325 shipped. Thanks

rk93, PM sent. Sorry I missed this post but it's still available if you want it.

Thanks.

Bump

are all of these gone???

Here's an updated photo showing which stocks are still available. I also have a Montana 84M stock with a grey finish but for some reason had a thin "rubbery" coating applied over the grey at some point. The coating is "sticky" but I think it could easily be removed using mineral spirits, acetone or similar.

One stocking stuffer left!! See below. If you don't like the color you can always paint it or have it dipped.

Bump. Mine just arrived. Nice stock and great seller.

Thanks AKduck. Good to hear that you like the stock and it was a pleasure doing business with you too. It would be good to see the finished product once you have everything sorted out.

So the smokehouse at 28.8 ounces is available?
I don’t want AKD’s stock to be lonely up here in the Greatland.

Yes, still available. If you have access to AKduck and want to look at his stock first perhaps he'll be ok with that. As I mentioned, they're painted with Sherwin Williams paint, same as Costa Rica so changing the color is no big deal.

Thanks.

Sent you a PM