|
|
Joined: Apr 2010
Posts: 601
Campfire Regular
|
OP
Campfire Regular
Joined: Apr 2010
Posts: 601 |
Is there a good way of removing glass bedding from the chamber area. I recently purchased a very nice Ruger 77RL in 250Savage, not so nice when I removed the barreled action from the stock. Any help would be appreciated.
|
|
|
|
Joined: Mar 2006
Posts: 3,237
Campfire Tracker
|
Campfire Tracker
Joined: Mar 2006
Posts: 3,237 |
molɔ̀ːn labé skýla
|
|
|
|
Joined: Dec 2012
Posts: 785
Campfire Regular
|
Campfire Regular
Joined: Dec 2012
Posts: 785 |
If your very gentle with a heat gun and dental pick I've found it better and cleaner in the end.
Three most useless things to a pilot are: 1. The altitude above you 2. The runway behind you 3. The fuel on the ground
|
|
|
|
Joined: Mar 2007
Posts: 9,213 Likes: 3
Campfire Outfitter
|
Campfire Outfitter
Joined: Mar 2007
Posts: 9,213 Likes: 3 |
Most of the bedding agents get pretty soft around 400* f.
I would not buy something that runs on any kind of primer given the possibility of primer shortages and even regulations. In fact, why not buy a flintlock? Really. Rocks aren't going away anytime soon.
|
|
|
|
Joined: May 2005
Posts: 16,554
Campfire Ranger
|
Campfire Ranger
Joined: May 2005
Posts: 16,554 |
I like a Dremel as you get down to clean wood, can leave roughened for better adhesion, is fast, and I somehow enjoy the old bedding flying all over the place. A little extra room inside the stock where the bedding won't be visible doesn't hurt anything.
HOWEVER, unless you're practiced using a Dremel it can get out of control when you least expect it and cause a major disaster.
The key elements in human thinking are not numbers but labels of fuzzy sets. -- L. Zadeh
Which explains a lot.
|
|
|
|
Joined: May 2003
Posts: 10,439 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2003
Posts: 10,439 Likes: 1 |
All you want is to get the bedding away from around the barrel, right? If so, a big dowel wrapped with 60 grit can do the job. Then come back with a finer grit. As long as you have one or perhaps two layers worth of masking tape clearance when you're done, you should be just fine. Make sure you clamp the stock down where you can use some force without things jumping around, it will go much faster. For cosmetics, you can "slick" the old stuff with a thin application of more epoxy, say with a gloved finger and a warm heat gun.
Up hills slow, Down hills fast Tonnage first and Safety last.
|
|
|
|
Joined: Jan 2001
Posts: 7,988 Likes: 3
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2001
Posts: 7,988 Likes: 3 |
Is it that the existing glass bed just isn't fitting well or is it just a poor job of bedding that you would like to redo?
If you have a die grinder and ball end die grinder bit, it will come out pretty quickly and you can then replace the bedding with a better product and installation. If it just doesn't look good or fits poorly, the sand paper and or curved rasps and files will work fine for cleaning it up.
Bob
Never underestimate your ability to overestimate your ability.
|
|
|
|
547 members (10ring1, 257 roberts, 1234, 270wsmnutt, 160user, 1lessdog, 71 invisible),
2,385
guests, and
1,172
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,194,576
Posts18,532,115
Members74,041
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|