|
Joined: Sep 2008
Posts: 5,734
Campfire Tracker
|
OP
Campfire Tracker
Joined: Sep 2008
Posts: 5,734 |
I need load recommendations for COW forming 338-378WBY.
A buddy has a P17 Enfield chambered in 338-378WBY and I necked up some new 30-378WBY cases to use in it but mine are .025" shorter at the shoulder than his fired cases.
He's fired factory WBY ammo in his rifle so I could load as is but I'd like to maximize case life and not start the cases off with a stretch.
Thanks
"Camping places fix themselves in your mind as if you had spent long periods of your life in them. You will remember a curve of your wagon track in the grass of the plain like the features of a friend." Isak Dinesen
|
|
|
|
Joined: Jul 2001
Posts: 60,161 Likes: 13
Campfire Kahuna
|
Campfire Kahuna
Joined: Jul 2001
Posts: 60,161 Likes: 13 |
Do the cases from the factory ammo he fired show signs of excessive stretching?
“Montana seems to me to be what a small boy would think Texas is like from hearing Texans.” John Steinbeck
|
|
|
|
Joined: Sep 2008
Posts: 5,734
Campfire Tracker
|
OP
Campfire Tracker
Joined: Sep 2008
Posts: 5,734 |
No,They all look fine. I'm a little nervous with a non factory chamber but the factory ammo fired well. I'm wishing he'd saved a single cartridge of the factory stuff for comparison but I have none.
"Camping places fix themselves in your mind as if you had spent long periods of your life in them. You will remember a curve of your wagon track in the grass of the plain like the features of a friend." Isak Dinesen
|
|
|
|
Joined: Jul 2001
Posts: 60,161 Likes: 13
Campfire Kahuna
|
Campfire Kahuna
Joined: Jul 2001
Posts: 60,161 Likes: 13 |
The problem with case stretching usually occurs with rimless cases fired in a slightly longer chamber. The case gets slammed forward by the firing pin, expands against the case wall, which unless there's considerable oil in the chamber, holds the case body while the case head gets pushed back against the bolt face. As a result the case stretches between the body and thicker head.
In a properly cut belted chamber, with decent brass (and Weatherby brass is usually good) the belt keeps the case from being shoved very far forward. As a result, the head is held firmly while the case body expands to fit the chamber. The only way the case will stretch between body and head is if the belt portion of the chamber is sloppily cut, or the belts on the brass are too short.
If a problem exists between the chamber and belt, then the COW method will also stretch brass, because if enough powder is used to expand the case fully the same thing happens.
I would try one round and see if there's any evidence of case over-stretching. But if your friend had been firing factory ammo with no problems then there shouldn't be with yours.
“Montana seems to me to be what a small boy would think Texas is like from hearing Texans.” John Steinbeck
|
|
|
|
Joined: Oct 2004
Posts: 2,139
Campfire Regular
|
Campfire Regular
Joined: Oct 2004
Posts: 2,139 |
I have seen new factory 300 win mag 20 thou short (Nosler and Winchester). I would seat the bullets to touch and use moderate loads. Bet they shoot just fine.
17 gr of Unique will bump them out
|
|
|
|
Joined: Sep 2008
Posts: 5,734
Campfire Tracker
|
OP
Campfire Tracker
Joined: Sep 2008
Posts: 5,734 |
Thank you Sir!
I needed some help to reason this puzzle out. I'll load a single round and will go from there.
"Camping places fix themselves in your mind as if you had spent long periods of your life in them. You will remember a curve of your wagon track in the grass of the plain like the features of a friend." Isak Dinesen
|
|
|
|
Joined: Dec 2007
Posts: 16,155 Likes: 7
Campfire Ranger
|
Campfire Ranger
Joined: Dec 2007
Posts: 16,155 Likes: 7 |
I'd like to maximize case life and not start the cases off with a stretch. I'd neck them up to 35 caliber first, then size them back down just enough to create a false shoulder to headspace on.
|
|
|
|
Joined: Jul 2005
Posts: 930
Campfire Regular
|
Campfire Regular
Joined: Jul 2005
Posts: 930 |
Even with the belt wouldn't aalf's suggestion be pretty good for minimizing case stretch?
|
|
|
|
Joined: Dec 2007
Posts: 16,155 Likes: 7
Campfire Ranger
|
Campfire Ranger
Joined: Dec 2007
Posts: 16,155 Likes: 7 |
Even with the belt wouldn't aalf's suggestion be pretty good for minimizing case stretch? With a proper crush fit, there'd be zero case stretch concerns. I've fireformed thousands of Dasher cases blowing the shoulder forward a hundred thou with a 40 degree shoulder, using a false shoulder with nary a problem.
|
|
|
|
Joined: Jun 2011
Posts: 2,789
Campfire Regular
|
Campfire Regular
Joined: Jun 2011
Posts: 2,789 |
I don't believe there is that much 'shoulder' created when you stretch the neck to create it. I've tried with with COW both ways and in the end there was not much difference in case life. What is 'short' for the shoulder is very common for even factory belted cases and I've seen no difference in case life with and without creating the false should. Blow them out both ways and see for yourself. I'll bet you'll be fine doing it the 'standard' way.
Used to be bobski, member since '01
|
|
|
|
Joined: Sep 2008
Posts: 5,734
Campfire Tracker
|
OP
Campfire Tracker
Joined: Sep 2008
Posts: 5,734 |
I'd like to maximize case life and not start the cases off with a stretch. I'd neck them up to 35 caliber first, then size them back down just enough to create a false shoulder to headspace on. Thanks AALF, It makes sense to capture the brass with the false shoulder and expand the brass shoulder forward to fit the chamber. I'll try both, some load and shoot and a false shoulder too, so I can see If either makes a difference in this rifle. If brass were cheaper I wouldn't hesitate but this stuff is a little steep. Link here Thanks for the replies!
Last edited by colodog; 07/18/16. Reason: add link
"Camping places fix themselves in your mind as if you had spent long periods of your life in them. You will remember a curve of your wagon track in the grass of the plain like the features of a friend." Isak Dinesen
|
|
|
|
Joined: Oct 2008
Posts: 7,263
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2008
Posts: 7,263 |
I would be tempted to just load and shoot after verifying the belt was functioning as a rim for head space. Any additional forming or false shoulder is just working the brass more.
Only issue is that you may need to adjust your loads after the initial firing as capacity will be increased slightly.
A big cartridge like this is a good candidate for reduced practice loads. A middling load with 160s or 180s would be impressive on a rock chuck.
"When you disarm the people, you commence to offend them and show that you distrust them either through cowardice or lack of confidence, and both of these opinions generate hatred." Niccolo Machiavelli
|
|
|
|
Joined: Jul 2001
Posts: 60,161 Likes: 13
Campfire Kahuna
|
Campfire Kahuna
Joined: Jul 2001
Posts: 60,161 Likes: 13 |
Which was my suggestion as well. If the belted cases headspace OK in the chamber, then they won't stretch.
One other note: Something I've seen happen more than occasionally when using a seated-out bullet or false shoulder to"hold" headspace is that heavy-striking firing pins (like those on most military rifles, including the 1917) often generate so much momentum they'll still push the case too far into the chamber. I've often had to remove the extractor-ball assembly from sizing dies to get a firm enough neck-grip on seated-out bullets, or neck the case up a lot more than normally suggested when creating a false shoulder.
“Montana seems to me to be what a small boy would think Texas is like from hearing Texans.” John Steinbeck
|
|
|
|
Joined: Oct 2008
Posts: 7,263
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2008
Posts: 7,263 |
Didn't mean to be redundant. Since you mentioned oily chambers is it advisable to fire form the first load in an oily chamber assuming it is not a max load? Some say this reduces stretching and forms better than a dry chamber.
I left Hornaday One wax on some 280 AI cases when doing COW forming and it seemed to work. Had a couple of miss fires that fired the second time due to case slippage. This was bulletless so no jamming.
"When you disarm the people, you commence to offend them and show that you distrust them either through cowardice or lack of confidence, and both of these opinions generate hatred." Niccolo Machiavelli
|
|
|
|
Joined: Jan 2007
Posts: 35,900
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jan 2007
Posts: 35,900 |
Had a 35 on an 8mm Rem mag case. Had no dies so used 358 Norma neck die with 375 H&H cases. Just ran them in the die to neck them down, then COW'd them in the new chamber.
Worked slick and never lost a case. I guess it headspaced on the belt for forming but it sure was easy to do.
The 280 Remington is overbore.
The 7 Rem Mag is over bore.
|
|
|
|
Joined: Jul 2001
Posts: 60,161 Likes: 13
Campfire Kahuna
|
Campfire Kahuna
Joined: Jul 2001
Posts: 60,161 Likes: 13 |
Tejano,
It's often good to be redundant on the Campfire! Many people don't read all the posts on a thread after the first few.
“Montana seems to me to be what a small boy would think Texas is like from hearing Texans.” John Steinbeck
|
|
|
|
Joined: Jul 2001
Posts: 60,161 Likes: 13
Campfire Kahuna
|
Campfire Kahuna
Joined: Jul 2001
Posts: 60,161 Likes: 13 |
Bob,
I also had a .35 Shooting Times Alaskan for a while, and also used .375 cases. But did have .35 STA dies, and fire-formed the cases while working up loads.
With belted cases that headspace correctly in the chamber, on the belt of that particular brass, there's no danger of case stretching. Same deal with rimmed case, like the .22 K-Hornet. The big problem is rimless cases. But occasionally there'll be a belted or rimmed chamber sloppy headspace, and those have to be treated like rimless chambers, using bullets seated into the lands or creating secondary shoulders.
“Montana seems to me to be what a small boy would think Texas is like from hearing Texans.” John Steinbeck
|
|
|
|
Joined: Oct 2008
Posts: 7,263
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2008
Posts: 7,263 |
Tejano,
It's often good to be redundant on the Campfire! Many people don't read all the posts on a thread after the first few. You can say that again.
"When you disarm the people, you commence to offend them and show that you distrust them either through cowardice or lack of confidence, and both of these opinions generate hatred." Niccolo Machiavelli
|
|
|
|
Joined: May 2014
Posts: 10,445 Likes: 2
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2014
Posts: 10,445 Likes: 2 |
It would have to be a really big case to put any of my cows in.
I prefer classic. Semper Fi I used to run with the hare. Now I'm envious of the tortoise and I do my own stunts but rarely intentionally
|
|
|
|
Joined: Sep 2008
Posts: 5,734
Campfire Tracker
|
OP
Campfire Tracker
Joined: Sep 2008
Posts: 5,734 |
It would have to be a really big case to put any of my cows in. I often wonder what a casual web-surfer concludes when reading our posts Thanks for all your thoughts and replies, I hope for a little range time this weekend and I'll post a report on findings!
"Camping places fix themselves in your mind as if you had spent long periods of your life in them. You will remember a curve of your wagon track in the grass of the plain like the features of a friend." Isak Dinesen
|
|
|
|
632 members (16gage, 1beaver_shooter, 160user, 1Longbow, 01Foreman400, 12344mag, 71 invisible),
2,921
guests, and
1,271
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,622
Posts18,492,736
Members73,972
|
Most Online11,491 Jul 7th, 2023
|
|
|
|