|
|
Joined: Dec 2007
Posts: 1,523
Campfire Regular
|
Campfire Regular
Joined: Dec 2007
Posts: 1,523 |
I doubt you'll see much difference at 100yds with an average hunting rifle by not resizing the neck after pulling and seating a new bullet. Neck tension will affect accuracy but the average rifle won't show how much (with statistical confidence) without shooting a LOT of 5-10 shot groups. A very accurate LR rifle or BR rifle may be a different story, but in that case I would only use such rounds for fouling or practice. Still, I will normally run the case back in the FL die and go about 2/3 down the neck but not touch the body. The de-cap pin is removed on all my FL dies and this method doesn't require any lube.
I use the Lee FC on a couple calibers and it will help, but you still won't have the "same" neck tension as on a round that had been re-neck sized. And either one would most likely be a little different than a case that had been fired and sized normally. It gets down to how fine do you want to pick your nits...
|
|
|
|
Joined: Nov 2010
Posts: 37,132 Likes: 1
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,132 Likes: 1 |
I doubt you'll see much difference at 100yds with an average hunting rifle by not resizing the neck after pulling and seating a new bullet. Neck tension will affect accuracy but the average rifle won't show how much (with statistical confidence) without shooting a LOT of 5-10 shot groups. A very accurate LR rifle or BR rifle may be a different story, but in that case I would only use such rounds for fouling or practice. Still, I will normally run the case back in the FL die and go about 2/3 down the neck but not touch the body. The de-cap pin is removed on all my FL dies and this method doesn't require any lube.
I use the Lee FC on a couple calibers and it will help, but you still won't have the "same" neck tension as on a round that had been re-neck sized. And either one would most likely be a little different than a case that had been fired and sized normally. It gets down to how fine do you want to pick your nits... Good points. DF
|
|
|
|
Joined: Sep 2016
Posts: 14
New Member
|
OP
New Member
Joined: Sep 2016
Posts: 14 |
Thanks guys , I'll go on and resize them for piece of mind.
|
|
|
|
Joined: Nov 2006
Posts: 24,451
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2006
Posts: 24,451 |
The Lee Collet Neck sizer dies work great for the situation you described. It is what I use if I need to pull bullets and then resize/reload. In the past I have had pressure issues with crimped loads when trying to work up loads. The accuracy was erratic at times also. This was with a 243 and problem went away when I quit crimping. This was just my experience. I used to crimp a standard 30-06 load that worked great in a lot of different rifles. But if I didn't crimp using the same load my personal rifles shot it more accurately. Not a great deal more accurate, but still noticeable at 100yds.
|
|
|
|
Joined: Nov 2010
Posts: 37,132 Likes: 1
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,132 Likes: 1 |
The Lee Collet Neck sizer is never a bad option...
DF
|
|
|
|
Joined: Nov 2007
Posts: 29,645 Likes: 5
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2007
Posts: 29,645 Likes: 5 |
The Lee Collet Neck sizer is never a bad option...
DF HUGE +1!!
|
|
|
|
80 members (7mm_Loco, 808outdoors, AKislander, 10gaugemag, 2ndwind, 44automag, 14 invisible),
1,414
guests, and
874
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,118
Posts18,483,494
Members73,966
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|