|
Joined: Dec 2006
Posts: 4,685
Campfire Tracker
|
OP
Campfire Tracker
Joined: Dec 2006
Posts: 4,685 |
Stopped by one of the local pawn shops today, and saw a rather odd gun in the rack. At first, I thought it was an old Daisy .22, but then noticed it had a lever. Pulled it down, and found it was an old single shot Revelation 103. According to Google, its nothing more than a rebadged Savage 89. ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4847_zpsuttpfpqt.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4852_zpswdvokzrf.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4857_zpsgmp3f6mp.jpg) Its a pretty neat little rifle, and nothing like any other "normal" lever .22 rifle. Its closer to a falling block, where the rear action block pivots down once the lever is dropped. ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4854_zpsmmlebhgg.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4855_zpsr9iur9hl.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4856_zpsl7nkxfim.jpg) It takes a little bit to get a LR shell in place, but ejection is crisp. Its not difficult, just different than anything I've ever messed with. Actually has a really good trigger, and doesn't seem to be too complicated. I doubt I will be taking it apart, as replacement parts are almost non-existent.
Last edited by Jason280; 11/21/16.
|
|
|
|
Joined: Dec 2006
Posts: 4,685
Campfire Tracker
|
OP
Campfire Tracker
Joined: Dec 2006
Posts: 4,685 |
Speaking of replacement parts, the only thing wrong with the rifle is its missing the front sight. I say missing, but it looks like it was actually ground off. ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4868_zps9lshivfs.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4861_zpsqzxm0k30.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4860_zpscc6m1zu3.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4864_zpsehnhbshn.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4862_zpscejymlq9.jpg) ![[Linked Image]](http://i15.photobucket.com/albums/a377/Jason280_5/Revelation%20103/DSCF4863_zps7dqn8b2u.jpg) I'm not sure what I am going to do about the front sight. To be honest, I'm not 100% sure what its supposed to even look like. I've tried finding a replacement, but no luck so far. I have found a couple similar styled sights on eBay, but not sure if they are the correct diameter. The barrel is 0.580", and the mag tube is 0.505" in diameter. The barrel/mag band is 0.590/0.515", so I would need to find something close. A Marlin 150 front sight looks close, or even a Marlin 70, but that would require me moving the barrel band back. I believe I could move the barrel band back 1/4", and then maybe simply drill/tap for a generic front sight. Looks like just about any plain front ramp style would work, just have to find one. Any suggestions?
|
|
|
|
Joined: Nov 2002
Posts: 33,764 Likes: 7
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2002
Posts: 33,764 Likes: 7 |
Looks like the Ithaca that was made by Erma, IIRC, in the 60's.
Conduct is the best proof of character.
|
|
|
|
Joined: Dec 2007
Posts: 68
Campfire Greenhorn
|
Campfire Greenhorn
Joined: Dec 2007
Posts: 68 |
IIRC 70 and may not as I am going on 70. Its a Ithaca mod.49
|
|
|
|
Joined: Nov 2005
Posts: 10,365
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2005
Posts: 10,365 |
It is a Ithaca 49, gun parts corp has a front sight for it, cost $12.95
|
|
|
|
Joined: Dec 2006
Posts: 4,685
Campfire Tracker
|
OP
Campfire Tracker
Joined: Dec 2006
Posts: 4,685 |
It is a Ithaca 49, gun parts corp has a front sight for it, cost $12.95 I found a few online, but their description has me a little hesitant to order. I mic'd my barrel, and it comes out at 0.580" in diameter...they list their sight as fitting 0.560". Now, the likelihood of Ithaca using different parts is slim, but I don't want to end up with a part I can't use. I'm really tempted to simply drill and tap my own front sight, and move the front band assembly back 1/4". The front sight/barrel band on these guns is held in place with a set screw, and isn't the most robust design. On the other hand, that is a lot of work for a gun that may not shoot minute-of-can at 25 yards!
|
|
|
|
Joined: Sep 2007
Posts: 26,524
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2007
Posts: 26,524 |
I found a few online, but their description has me a little hesitant to order. I mic'd my barrel, and it comes out at 0.580" in diameter...they list their sight as fitting 0.560".
So your barrel is 0.58" and the part 0.56". a dowel rod and some sand paper makes that happen....
|
|
|
|
Joined: Nov 2005
Posts: 23,123 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2005
Posts: 23,123 Likes: 2 |
Ditto. It looks like pot metal and probably take all of 5 minutes to hone to fit.
Speaking of pot metal, what's under the paint on the receiver? In the pic it looks like aluminum or something where the paint is worn away.
The Ithaca 49 was a dandy little rifle, well made and accurate. This one, even though it copies the Martini-like design of the Ithaca looks to be very crudely made, like in a jungle workshop somewhere. I wouldn't invest too much time or money in it.
"You can lead a man to logic, but you cannot make him think." Joe Harz "Always certain, often right." Keith McCafferty
|
|
|
|
Joined: Dec 2012
Posts: 1,990
Campfire Regular
|
Campfire Regular
Joined: Dec 2012
Posts: 1,990 |
Looks exactly like my Ithaca 49. If it is its probably made of aluminum wanted to get mine reblued a few years ago and that's how found out.
|
|
|
|
Joined: Dec 2006
Posts: 4,685
Campfire Tracker
|
OP
Campfire Tracker
Joined: Dec 2006
Posts: 4,685 |
I'm assuming the receiver is some kind of die-cast zinc alloy, but not sure. I vaguely remember it being magnetic, need to check again to make sure.
|
|
|
|
Joined: Dec 2006
Posts: 4,685
Campfire Tracker
|
OP
Campfire Tracker
Joined: Dec 2006
Posts: 4,685 |
Just checked, and I *think* the receiver and lever may actually be aluminum.
|
|
|
|
Joined: Jan 2005
Posts: 53,303
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2005
Posts: 53,303 |
Hot chamber die cast ZAMAC.
GTC
Member, Clan of the Border Rats -- “Sometimes I wonder whether the world is being run by smart people who are putting us on or by imbeciles who really mean it.”- Mark Twain
|
|
|
|
Joined: Nov 2005
Posts: 10,365
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2005
Posts: 10,365 |
I found a few online, but their description has me a little hesitant to order. I mic'd my barrel, and it comes out at 0.580" in diameter...they list their sight as fitting 0.560".
So your barrel is 0.58" and the part 0.56". a dowel rod and some sand paper makes that happen.... +1 on the dowel rod, remember it's a press fit and 0.02 isent much metal to work with, plus I'm sure the pot metal will streched alittle. Don't want it to just slide on with finger pressure, as it will shoot loose
|
|
|
|
Joined: Dec 2006
Posts: 4,685
Campfire Tracker
|
OP
Campfire Tracker
Joined: Dec 2006
Posts: 4,685 |
Last edited by Jason280; 12/08/16.
|
|
|
|
Joined: May 2014
Posts: 10,458 Likes: 3
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2014
Posts: 10,458 Likes: 3 |
I found a few online, but their description has me a little hesitant to order. I mic'd my barrel, and it comes out at 0.580" in diameter...they list their sight as fitting 0.560".
So your barrel is 0.58" and the part 0.56". a dowel rod and some sand paper makes that happen.... I think there's your answer
I prefer classic. Semper Fi I used to run with the hare. Now I'm envious of the tortoise and I do my own stunts but rarely intentionally
|
|
|
|
Joined: Jul 2016
Posts: 4,124 Likes: 6
Campfire Tracker
|
Campfire Tracker
Joined: Jul 2016
Posts: 4,124 Likes: 6 |
I have one of the Ithaca 49s in 22 wmr . Fun little rifle and I'll agree with the above poster . Wooden dowel rod and sandpaper. Possibly a round file nearly the same diameter.
|
|
|
|
606 members (160user, 1beaver_shooter, 1badf350, 1936M71, 1lessdog, 68 invisible),
2,774
guests, and
1,307
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,193,192
Posts18,503,481
Members73,993
|
Most Online11,491 Jul 7th, 2023
|
|
|
|