|
Joined: Apr 2017
Posts: 3,282
Campfire Tracker
|
OP
Campfire Tracker
Joined: Apr 2017
Posts: 3,282 |
upstairs guest room vanity sink has a TINY pinhole leak from coming between the "T" and the cold water intake, about an INCH from the joint. I think it is too close to cut and put a Shark Bite over. The "t" is soldered on also and I would have to rip out a large portion of copper to replace it. Anything else a permanent solution, that I'm overlooking?
Last edited by Sasha_and_Abby; 12/24/17.
"If there are no dogs in Heaven, then when I die, I want to go where they went" Will Rogers
|
|
|
|
Joined: Aug 2004
Posts: 69,722 Likes: 30
Campfire Kahuna
|
Campfire Kahuna
Joined: Aug 2004
Posts: 69,722 Likes: 30 |
Molɔ̀ːn Labé Skýla!
|
|
|
|
Joined: Aug 2006
Posts: 22,950 Likes: 21
Campfire Ranger
|
Campfire Ranger
Joined: Aug 2006
Posts: 22,950 Likes: 21 |
Why not just fix it right?
|
|
|
|
Joined: Jan 2001
Posts: 21,317
Campfire Ranger
|
Campfire Ranger
Joined: Jan 2001
Posts: 21,317 |
When it comes to plumbing leaks, the simplest and easiest fix is the proper permanent fix to the leak as you find it. Every time I've put off a proper fix of a home issue regarding water, I've had 10 times as much work.
|
|
|
|
Joined: Aug 2004
Posts: 69,722 Likes: 30
Campfire Kahuna
|
Campfire Kahuna
Joined: Aug 2004
Posts: 69,722 Likes: 30 |
I only use the tape when I have to. After years of running ranch water systems, and stopping leaks needs to be quick since driving into town to get what you need may entail most of the day, I started carrying a roll of that tape everywhere I go. It works. But if you got the means to fix it permanently, do so. That tape will stop further damage til you do.
Molɔ̀ːn Labé Skýla!
|
|
|
|
Joined: Jun 2007
Posts: 14,370
Campfire Outfitter
|
Campfire Outfitter
Joined: Jun 2007
Posts: 14,370 |
A little of that tape and some PC-7 smeared around the pipe ought to be about as permanent as it gets other than a major plumbing job.... https://www.pcepoxy.com/products/permanent-repair/pc-7-paste-epoxy/
Last edited by Middlefork_Miner; 12/24/17.
|
|
|
|
Joined: Apr 2011
Posts: 152,086 Likes: 32
Campfire Savant
|
Campfire Savant
Joined: Apr 2011
Posts: 152,086 Likes: 32 |
Fix it right, then you won’t have to think about it anymore
|
|
|
|
Joined: Dec 2010
Posts: 14,408
Campfire Outfitter
|
Campfire Outfitter
Joined: Dec 2010
Posts: 14,408 |
if you have a pin hole in a copper pipe then you probably have old corroded pipes full of deposits. tear it down and fix it right.
My diploma is a DD214
|
|
|
|
Joined: Apr 2011
Posts: 152,086 Likes: 32
Campfire Savant
|
Campfire Savant
Joined: Apr 2011
Posts: 152,086 Likes: 32 |
|
|
|
|
Joined: Sep 2014
Posts: 21,907 Likes: 7
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2014
Posts: 21,907 Likes: 7 |
if you have a pin hole in a copper pipe then you probably have old corroded pipes full of deposits. tear it down and fix it right. Agreed,. Hope I am wrong, but I forsee more plumbing problems. If you find a few more of these in the next year or so, it might be best to replace your copper. PEX is the answer, and will not corrode.
Parents who say they have good kids..Usually don't!
|
|
|
|
Joined: Jan 2009
Posts: 3,001
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2009
Posts: 3,001 |
As has been said, get some pex tubing and some pex fittings and have fun with the simplicity of the fix. You'll have that job done in the amount of time it takes to brew yourself a cup of coffee.
"I'd rather have an Army of Asses led by a Lion, than an Army of Lions led by an Ass." (George Washington)
|
|
|
|
Joined: Aug 2010
Posts: 28,301 Likes: 5
Campfire Ranger
|
Campfire Ranger
Joined: Aug 2010
Posts: 28,301 Likes: 5 |
|
|
|
|
Joined: May 2003
Posts: 16,971 Likes: 1
Campfire Ranger
|
Campfire Ranger
Joined: May 2003
Posts: 16,971 Likes: 1 |
Here you go.
Go buy a copper pipe coupler - it will slide over the the existing pipe.
Cut the pipe in half where that pin hole is. And cut about a 1/16th of an inch out, then push the pipe aside and slide the coupler up it, and slide it back over the bottom half and then you are ready to solder it.
Make sure you clean the outside of the pipe very, very well before you start - and make sure you put plenty of flux on it. Also try to Shield the T from getting too hot by putting a vice grip on it, and putting a soldering heat shield over it.
|
|
|
|
Joined: May 2006
Posts: 495
Campfire Member
|
Campfire Member
Joined: May 2006
Posts: 495 |
Here you go.
Go buy a copper pipe coupler - it will slide over the the existing pipe.
Cut the pipe in half where that pin hole is. And cut about a 1/16th of an inch out, then push the pipe aside and slide the coupler up it, and slide it back over the bottom half and then you are ready to solder it.
Make sure you clean the outside of the pipe very, very well before you start - and make sure you put plenty of flux on it. Also try to Shield the T from getting too hot by putting a vice grip on it, and putting a soldering heat shield over it.
This is good advice, you will more then likely find more showing up. Probably will need to replace water lines in the near future
|
|
|
|
Joined: Jun 2005
Posts: 8,899
Campfire Outfitter
|
Campfire Outfitter
Joined: Jun 2005
Posts: 8,899 |
Go with your first instincts and rip out a large portion of copper and replace it
One man with courage makes a majority....
~Molɔ̀ːn Labé Skýla~
|
|
|
|
Joined: May 2003
Posts: 16,971 Likes: 1
Campfire Ranger
|
Campfire Ranger
Joined: May 2003
Posts: 16,971 Likes: 1 |
If you have ever heard of “PEX” you may want to replace the run with pex vs. copper, that way you don’t have to worry about soldering.
|
|
|
|
Joined: Nov 2005
Posts: 10,285 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2005
Posts: 10,285 Likes: 1 |
You have one then you probably have more coming. Consider the possibility of pulling the run and replacing it with PEX. http://www.dailyherald.com/article/20141114/entlife/141119476/
Last edited by Armednfree; 12/24/17.
The older I become the more I am convinced that the voice of honor in a man's heart is the voice of GOD.
|
|
|
|
Joined: Jan 2004
Posts: 11,406 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2004
Posts: 11,406 Likes: 1 |
For you Pex guys, what type of connection do you use. There are two types the typical homeowner could use, crimp and cinch rings. Then a step up I think is the tool that expands the tubing to recurve the fitting. This allows 1/2” tubing to have actual 1/2” fittings.
|
|
|
|
Joined: Dec 2003
Posts: 86,318 Likes: 30
Campfire Oracle
|
Campfire Oracle
Joined: Dec 2003
Posts: 86,318 Likes: 30 |
Assuming you are on a well, check the pH of the water. Sounds like corrosion.
If you take the time it takes, it takes less time. --Pat Parelli
American by birth; Alaskan by choice. --ironbender
|
|
|
|
Joined: Oct 2009
Posts: 1,771
Campfire Regular
|
Campfire Regular
Joined: Oct 2009
Posts: 1,771 |
I use the crimp rings. It either leaks or it doesn’t when using those. Also use brass connections with led not the plastic ones.
|
|
|
|
588 members (12344mag, 160user, 222ND, 1lessdog, 1beaver_shooter, 1badf350, 60 invisible),
2,428
guests, and
1,279
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,193,608
Posts18,511,652
Members74,007
|
Most Online11,491 Jul 7th, 2023
|
|
|
|