|
Joined: Nov 2006
Posts: 571
Campfire Regular
|
Campfire Regular
Joined: Nov 2006
Posts: 571 |
If that is the "angle-lok" ring I fear you will find it unsatisfactory. I tried them on other rifles and they didn't hold up very well. Even the steel CZ rings are preferable to me.
Anything Worth Doing Is Worth Overdoing
|
|
|
|
Joined: Oct 2007
Posts: 2,153 Likes: 2
Campfire Regular
|
Campfire Regular
Joined: Oct 2007
Posts: 2,153 Likes: 2 |
Yes I do SoTexasH, you can see the front sight in the lower center of the scope eyepiece, but I don't find it distracting and it blocks very little of the view. I have an NECG Masterpiece adjustable rear sight and a CZ Hi-ViS front sight on mine.
Regards,
Chuck
"There's a saying in prize fighting, everyone's got a plan until they get hit"
Ghost And The Darkness
|
|
|
|
Joined: Jan 2006
Posts: 5,720
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2006
Posts: 5,720 |
These are Lynx,30mm.They work well and stay tight.
Come on America, Athletes and actors are not heroes, only soldiers, airmen,marines and sailors get that respect�and let's add firemen and LEO's
|
|
|
|
Joined: Apr 2008
Posts: 2,609
Campfire Regular
|
OP
Campfire Regular
Joined: Apr 2008
Posts: 2,609 |
I think I have a regular one inch scope.. Vortex 2-7 x 32.. I have been thinking of the Warne CZ 550 19mm 1" medium quick Detach rings. They are $66 (Plus shipping) at Midsouth Shooters. Was only trying to figure out whether medium or high configuration would clear the sight picture with the iron sights on the barrel. The Tallys look good too but seem to be about $50 more. Some have mentioned Leupold but haven't really seen them for this model.
|
|
|
|
Joined: Apr 2007
Posts: 1,951
Campfire Regular
|
Campfire Regular
Joined: Apr 2007
Posts: 1,951 |
I have a 1.5-4.5x scope on my CZ with the Talley rings, and when it is at 3x the front sight post is barely visible. If you shoot alot at lower magnification it may bother you, but if you are above 3x it wont be a concern. The sights aren't always in the field of vision no matter what the magnification is. Its hard to decide on what to get when you don't have it all in front of you to compare.
"Give a lazy man the toughest job, and he will find the easiest way to do it"
|
|
|
|
Joined: Apr 2008
Posts: 2,609
Campfire Regular
|
OP
Campfire Regular
Joined: Apr 2008
Posts: 2,609 |
What I was trying to figure is the Warne QD Mounts for CZ 550 come in low, medium and high height.. I called CZ America and they really couldn't say for sure..Just that they sold Warne,..lol Steven
|
|
|
|
Joined: Apr 2002
Posts: 21
New Member
|
New Member
Joined: Apr 2002
Posts: 21 |
I mounted the Millet rings on my CZ550, 9,3x62, and they are darn near impossible to keep tight! Even checking as often as I did, they still flew off the rifle during a shooting session of 286-gr TSX bullets. Anyone who owns a 9,3 KNOWS the recoil is nothing like a 375 H&H.
Anyway, I've since ordered some Burris CZ550 rings and they snug up nice and tight. The down side was when I was removing the Millet rings, I'd tightened them so much I destroyed my scope.
My new scope should be here towards the end of this week so I can finally finish up my load development and chronographing. Only have one more bullet to work with: Barnes 250-gr TSX.
So far though, the 286-gr TSX is very accurate, easily get 2330 fps MV(five shot aggregate), which is sufficient for my purposes.
I'm in a crunch for time at this point, but I may have CZs scope "bases" milled off, and have the reciever drilled & tapped for a better quality of base at a later date.
|
|
|
|
529 members (117LBS, 1234, 12344mag, 10gaugeman, 06hunter59, 1badf350, 55 invisible),
2,717
guests, and
1,257
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,194,792
Posts18,536,373
Members74,041
|
Most Online11,491 Jul 7th, 2023
|
|
|
|