Home Forums Gear Free Classifieds Mc Millan stocks

I have three black Mc Millan stocks. The first one is I think for a ruger. It looks to be 6-7/8 center to center and recoil lug area is 11/16 wide,It has had a stud hole filled in back near recoil pad.It has a pachmayr recoil pad.Black texture finish and black studs. Has a very small chip at front top end of stock, I will get pics,275.00 shipped. Next stock is for a winchester,it is a black texture stock with piller bed and with cheekpiece. It is 7-1/2 inches center to center bolt holes. It has about 3/4-inch barrel channel opening 3-inches from front end of stock.Has Decelerator pad,dont know for sure but would guess length of pull at about 13-1/2 inches.325.00 shipped. Last is a winchester that has had barrel channel opened up to about 15/16 at about 3-inches from front end of stock where stud is mounted.Has a decelerator pad which has seperated about 2 inches but is still attached to stock but can be seperated with your hand. It does not have a cheekpiece, probably about 13-1/2 inch trigger pull, 275.00 shipped.

Is there anyway i can get a pic of stock#2?

I think the winchester stocks arew for pre 64, I do not know if rear tang area can be modified to fit post 64? Cary

Sent you a message on stock #1.

I do not think #1 is for ruger, center to center is 6-7/8 inches with rear bolt going through middle of recoil lug? anybody know what it fits? Cary

If the front action screw is at an angle, and goes right through the recoil lug, it's for a Ruger.

Pics would help.

bump

Still waiting for pics...

Pics of Ruger Stock

Last Ruger picture

Winchester W Cheekpiece

Winchester with NO Cheek Piece













[img]http://i257.photobucket.com/albums/hh216/dirtydave1/CARYS%20GUNS%20N%20STUFF/WINNOCP6.jpg[/img]

[img]http://i257.photobucket.com/albums/hh216/dirtydave1/CARYS%20GUNS%20N%20STUFF/WINNOCP7.jpg[/img]

I have three black Mc Millan stocks.

The first one is I think for a ruger. It looks to be 6-7/8 center to center and recoil lug area is 11/16 wide,It has had a stud hole filled in back near recoil pad.It has a pachmayr recoil pad.Black texture finish and black studs. Has a very small chip at front top end of stock,
Pics posted $275.00 shipped.

Next stock is for a winchester,it is a black texture stock which is piller beded and has a cheekpiece. It is 7-1/2 inches center to center bolt holes. It has about 3/4-inch barrel channel opening 3-inches from front end of stock. Also has a Decelerator pad,dont know for sure but would guess length of pull at about 13-1/2 inches.
Pics are posted $325.00 shipped.

Last is a Winchester that has had barrel channel opened up to about 15/16 at about 3-inches from front end of stock where stud is mounted.Has a decelerator pad which has seperated about 2 inches but is still attached to stock but can be seperated with your hand. It DOES NOT have a cheekpiece, probably about 13-1/2" length of pull.
Pics are Posted $275.00 shipped.

The first stock is not for ruger, anybody know what has 6-7/8 center to center with front bolt goong in center of recoil lug? I am reducing all three stocks by 25.00.

#1 is a Sako medium L579, maybe an AII

offer sent on #3

Thanks for info on stock #1, It is for sako medium action.

#3 winchester with no cheekpiece sold to Free miner,thanks, Cary

I'll take the Sako stock as mentioned in our PM.

McMillan sako stock sold pending funds ,Thanks Cary

Lower price on #2 winchester with cheekpiece 275.00 shipped, Cary