|
|
Joined: Feb 2010
Posts: 1,065
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2010
Posts: 1,065 |
Does anyone know what the twist rate of a Remington Model 700 in 6mm Rem is/or should be?
Thanks.
|
|
|
|
Joined: Aug 2010
Posts: 48,036
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Aug 2010
Posts: 48,036 |
It "should" be a 1 in 9" twist rate if it is stamped "6mm rem" on the barrel. If it says 244 remington, it should be 1 in 12" twist.
I try to stick with the basics, they do so well. Nothing fancy mind you, just plain jane will get it done with style. You want to see an animal drop right now? Shoot him in the ear hole. BSA MAGA
|
|
|
|
Joined: Jul 2005
Posts: 12,524
Campfire Outfitter
|
Campfire Outfitter
Joined: Jul 2005
Posts: 12,524 |
You can roll a turd in peanuts, dip it in chocolate, and it still ain't no damn Baby Ruth.
|
|
|
|
Joined: Feb 2006
Posts: 2,483
Campfire Regular
|
Campfire Regular
Joined: Feb 2006
Posts: 2,483 |
The older 6mm rem were originally marked as "244 Remington" on the barrel rather than "6mm Remington". These older guns had a 1-12" twist rate and most(not all) would not stabilize anything much heavier than about 90grs in bullet weight with the types of bullets then available. That is one of the major reasons the 243 winchester got out of the starting gates quicker than the 6mm Rem. Winchester saw the 243 as a dual purpose varmit/hunting cartridge and Remington (in their marketing wisdom) saw the 6mm as primarily a varmit cartridge that would be used occasionally as a hunting round - So they twisted it at 1-12" to shoot lighter bullets the best. Later Remington saw it's mistake and renamed the cartridge "6mm Remington", marked it's barrels as such and started twisting the barrels at 1-9" to compensate (or over compensate, given the 243 W only had a 1-10" from the start). They twist some of them differently these days to allow for heavier/longer bullets (such as VLD target type and copper).
Your rifle from that time period (mid-70s) most likely has the 1-9" twist, but could be different(like a 1-10").
You can check it yourself to be sure if you'd like to:
1.Take a cleaning rod and install a cleaning patch that fits tight enough to turn the cleaning rod.
2.Insert rod w/patch in the end of your barrel (either end will work, but on a bolt action your can pull the bolt and insert from the receiver to protect the barrel crown)and push until you see the rod start to turn.
3.Take a marking pen and make a mark across the cleaning rod where it is at the edge of the barrel or receiver. Then make another reference mark on top of the cleaning rod near the handle.
4.Push the rod in slowly and carefully watch for the reference mark on top of the rod near the handle to make a full revolution and come back to where it was when you started (one full turn on the rod).
5.Make another mark across the rod where it contacts the barrel or receiver.You now have two cross marks on the rod that it took one full turn to get to.
6.Pull the rod back out, take a tape measure and measure the distance between the two cross marks on the cleaning rod. If it measures closest to 10" you have a 1-10" twist, etc.
To answer another part of you're question: The twist should be for the type of bullets you intend to shoot, but with factory barrels you are limited to what they sell you. Most people go with at least a 1-9" to shoot the 105gr VLD type bullets for example.
Good Luck, Ted
|
|
|
|
Joined: Feb 2010
Posts: 1,065
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2010
Posts: 1,065 |
Great info guy's. Thanks! I'm going to reload for a friend who has a Rem 700, 6mm. He want's to shoot 55 grain bullet's. I figured this could be an issue dependant on twist rate. I've never really heard of folks raving about accuracy with 55's from their 6mm/243's. Sounds like 80gr plus bullet's might be a better alternative. These loads will be used for general varmit hunting.
|
|
|
|
Joined: Mar 2007
Posts: 1,402
Campfire Regular
|
Campfire Regular
Joined: Mar 2007
Posts: 1,402 |
I load 55 gr. Nosler BT's in a Rem 700 and get great accuracy. Two powders I have found for these loads are IMR4895 and Varget.
|
|
|
|
542 members (1badf350, 1936M71, 160user, 17CalFan, 12344mag, 10gaugemag, 53 invisible),
2,624
guests, and
1,377
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,191,704
Posts18,475,294
Members73,941
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|