|
Joined: Jan 2012
Posts: 14
New Member
|
OP
New Member
Joined: Jan 2012
Posts: 14 |
I recently just got a Kahr cw45. I've shot probably about 150 rounds through it. Today I went down and the first shot fired and the gun chambered another round. The slide did not go all the way forward. The slide is now stuck about 1/8 inch from fully forward. It will move about an eighth inch but will not fire the round and the slide will not move. The position it is stuck in is too far forward to take the slide off. Are there any other ways to get the slide off? I�ve run out of ideas. Any advice is welcome.
Thanks!
|
|
|
|
Joined: Nov 2003
Posts: 3,874
Campfire Tracker
|
Campfire Tracker
Joined: Nov 2003
Posts: 3,874 |
Certainly you have taken the magazine out, right?
RS
|
|
|
|
Joined: Jan 2012
Posts: 14
New Member
|
OP
New Member
Joined: Jan 2012
Posts: 14 |
Right the magizine is out.
|
|
|
|
Joined: Jan 2007
Posts: 11,578 Likes: 6
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2007
Posts: 11,578 Likes: 6 |
dump it if it !! if it is one with issues it will always be a POS.in the mind of the one carrying it you will aways have a dought if it will work in the time of need I know I had one , key word had. do some internet search on problems with a cw 45.
Last edited by ldholton; 03/29/12.
|
|
|
|
Joined: Feb 2002
Posts: 32,044
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Feb 2002
Posts: 32,044 |
You should be able to open the slide with just a hard quick jerk.
A Doe walks out of the woods today and says, that is the last time I'm going to do that for Two Bucks.
|
|
|
|
Joined: Jan 2001
Posts: 59,170 Likes: 2
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2001
Posts: 59,170 Likes: 2 |
You should be able to open the slide with just a hard quick jerk. Yep.. And possibly a little tap with a non-marring hammer coupled with backward pull on the slide.. The operative word there is LITTLE re: tap.. You didn't mention if this was factory ammo or reloads.. If factory, examine closely the case when it comes out and also every other loaded round in the box. Check for any deformed cases.. I've had that happen a couple times.. Not the gun's fault - it was the ammo.
Ex- USN (SS) '66-'69 Pro-Constitution. LET'S GO BRANDON!!!
|
|
|
|
Joined: Aug 2003
Posts: 13,547
Campfire Outfitter
|
Campfire Outfitter
Joined: Aug 2003
Posts: 13,547 |
Place the face of the slide, the small flat above the muzzle, against a table edge or work bench top and give the pistol a sharp shove.
Forgive me my nonsense, as I also forgive the nonsense of those that think they talk sense. Robert Frost
|
|
|
|
Joined: Jun 2003
Posts: 10,596 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Jun 2003
Posts: 10,596 Likes: 1 |
. . . or put it in a holster and bring it to a gunsmith and ask him to unchamber the round. I don't mind messing with a gun, but when it gets to hammering chabmered guns or pounding them on table edges to do an administrative unload, I would just call in an expert.
"Don't believe everything you see on the Internet" - Abraham Lincoln
|
|
|
|
Joined: Aug 2003
Posts: 13,547
Campfire Outfitter
|
Campfire Outfitter
Joined: Aug 2003
Posts: 13,547 |
...pounding them on table edges... I wouldn't do that either nor did I advise the OP to do that.
Forgive me my nonsense, as I also forgive the nonsense of those that think they talk sense. Robert Frost
|
|
|
|
Joined: Jan 2001
Posts: 59,170 Likes: 2
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2001
Posts: 59,170 Likes: 2 |
. . . or put it in a holster and bring it to a gunsmith and ask him to unchamber the round. I don't mind messing with a gun, but when it gets to hammering chabmered guns ...... Not 'hammering'... A gentle tap will do while applying rearward pressure on the slide.... Bubbas hammer things..
Last edited by Redneck; 03/30/12.
Ex- USN (SS) '66-'69 Pro-Constitution. LET'S GO BRANDON!!!
|
|
|
|
Joined: Jun 2003
Posts: 10,596 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Jun 2003
Posts: 10,596 Likes: 1 |
I don't consider myself to be a Bubba, but I don't have any technical skills, either. I'm much better at writing checks than fixing stuff. (I am good at breaking stuff, though.)
"Don't believe everything you see on the Internet" - Abraham Lincoln
|
|
|
|
Joined: Feb 2001
Posts: 73,096
Campfire Kahuna
|
Campfire Kahuna
Joined: Feb 2001
Posts: 73,096 |
Put the slide against a wooden bench edge and bump the frame forward. Or take it to a Smith that will do just that.
George Orwell was a Prophet, not a novelist. Read 1984 and then look around you!
Old cat turd!
"Some men just need killing." ~ Clay Allison.
I am too old to fight but I can still pull a trigger. ~ Me
|
|
|
|
568 members (16penny, 16gage, 160user, 06hunter59, 10gaugeman, 1beaver_shooter, 62 invisible),
2,799
guests, and
1,234
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,622
Posts18,492,791
Members73,977
|
Most Online11,491 Jul 7th, 2023
|
|
|
|