|
Joined: Dec 2010
Posts: 2,633 Likes: 1
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2010
Posts: 2,633 Likes: 1 |
Gentlemen; I have had come into my possession some of the Hornady .430 265g FTX bullets and was considering using them in my wife's .44 mag Marlin 1894. In order for the rounds to feed properly the cases need to be trimmed to 1.1 of an inch, when seated appropriately for crimping about .5 of an inch of bullet extends into the case. I realize the bullets are listed for the .444 Marlin on the Hornady website.
Is it prudent to attempt to load these or should I stick with the 240g Hornady XTPs I also have on hand?
Thank you in advance for your comments. GRF
|
|
|
|
Joined: Jan 2001
Posts: 2,762
Campfire Regular
|
Campfire Regular
Joined: Jan 2001
Posts: 2,762 |
The case needs to be cut to use the 225gr XFT in the 44, I doubt cutting the case short will result in enough clearance for the longer 265gr to work in the cartridge. The bullet was IIRC designed for the 444 and not intended for the 44 mag.
Been wrong before though.
I must confess, I was born at a very early age. --Groucho Marx
Patriotism is supporting your country all the time and your government when they deserve it. --Mark Twain
|
|
|
|
Joined: Jul 2010
Posts: 1,341
Campfire Regular
|
Campfire Regular
Joined: Jul 2010
Posts: 1,341 |
I think you need the 240 FXT for your revolver.
Originally Posted By: P_Weed
I never met a gun I didn't like.
SEdge,
I have an AMT Hardballer I can fix you up with.
|
|
|
|
Joined: Dec 2010
Posts: 2,633 Likes: 1
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2010
Posts: 2,633 Likes: 1 |
Marlin 1894...rifle. Thanks GRF
|
|
|
|
Joined: Jan 2008
Posts: 1,413
Campfire Regular
|
Campfire Regular
Joined: Jan 2008
Posts: 1,413 |
GTF: Instead of trimming the case, trim the cartridge lifter on the Marlin action. Instructions are on Beartooth Bullets website.
|
|
|
|
Joined: Nov 2006
Posts: 10,836 Likes: 3
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2006
Posts: 10,836 Likes: 3 |
Given the results I've had and I've seen others get with the 240 grain XTP in revolvers and carbines, I think I'd be reluctant to spend time and energy doing the requisite tinkering to make a trick bullet of questionable advantage work in your Marlin. Just my opinion.
Mathew 22: 37-39
|
|
|
|
Joined: May 2009
Posts: 17,299 Likes: 5
Campfire Ranger
|
Campfire Ranger
Joined: May 2009
Posts: 17,299 Likes: 5 |
Can't you seat it to max 44 coal and use the Lee factory crimp die?
That is what I do in my 444 marlin with the .429" 300 grain sierra which is meant for the 44 mag.
|
|
|
|
Joined: Dec 2010
Posts: 2,633 Likes: 1
Campfire Regular
|
OP
Campfire Regular
Joined: Dec 2010
Posts: 2,633 Likes: 1 |
There are no issues with the 240 grain, it was 265 g FTX meant for the .444 I was pondering. Thanks GRF
|
|
|
|
Joined: May 2009
Posts: 17,299 Likes: 5
Campfire Ranger
|
Campfire Ranger
Joined: May 2009
Posts: 17,299 Likes: 5 |
I was talking about the 265.
|
|
|
|
Joined: Apr 2004
Posts: 42,942 Likes: 16
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Apr 2004
Posts: 42,942 Likes: 16 |
Don't think the bullet will open as well at the lower velocities... but wouldn't matter if you are just punching paper...
I have loaded the 225 gr FTX in my 444... but then again, that was behind a load of Trail Boss, so we are talking like 900 fps MV....but I let one of the local kids use it for deer hunting this fall... the local deer population didn't cooperate real well tho...not showing up at the given times..
"Minus the killings, Washington has one of the lowest crime rates in the Country" Marion Barry, Mayor of Wash DC
“Owning guns is not a right. If it were a right, it would be in the Constitution.” ~Alexandria Ocasio Cortez
|
|
|
|
595 members (06hunter59, 17CalFan, 12344mag, 1lessdog, 1OntarioJim, 1beaver_shooter, 65 invisible),
2,996
guests, and
1,241
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,194,677
Posts18,534,241
Members74,041
|
Most Online11,491 Jul 7th, 2023
|
|
|
|