|
Joined: Nov 2011
Posts: 1,846
Campfire Regular
|
OP
Campfire Regular
Joined: Nov 2011
Posts: 1,846 |
I am fixing to order a stock and checking to see what thickness of recoil lug i should use. I have a savage 116 flat rear reciever with a 300win mag barrel in it for now and fixing to unscrew it and put a 30" mcgowen 338 edge barrel in its place. The recoil lug thats on action is 3/32" thick should i go with a 1/4"? What the thoughts on it and i have the brass and dies for it. Should i head space with a sized piece of brass or get a go gauge? Please let me know what you think?
Lifetime Christian
NRA Lifetime Member
Had rather be judged by 12 than carried by 6.
Your 9mm should expand but my 45 wont shrink.
|
|
|
|
Joined: Jan 2001
Posts: 30,793 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jan 2001
Posts: 30,793 Likes: 9 |
T R U M P W O N !
U L T R A M A G A !
|
|
|
|
Joined: Nov 2012
Posts: 141
Campfire Member
|
Campfire Member
Joined: Nov 2012
Posts: 141 |
In Otteson's book "the bolt action rifle. The savage action was head spaced on an "assembly gage" is was an under size gage (by .002") that would set the barrel a little tight. Then the barrel would seat upon test firing growing the head space the .002" being correct. It makes sense but never tried it so i can't say. I would though trust Stuart Otteson's word though on anything he wrote about.
|
|
|
|
Joined: Oct 2008
Posts: 1,628
Campfire Regular
|
Campfire Regular
Joined: Oct 2008
Posts: 1,628 |
I use a .240 lug on Rem 700's. I headspace the Edge on a gauge. But where the Savage is readily adjustable, a new, unfired case should work fine. I would set it to make full contact though.
Lock, Stock and Barrel gunworks SLC, Ut USMC 69-73
"This is my rifle, there are many like it but this one is mine. My rifle is my best friend, it is my life."
|
|
|
|
Joined: Jan 2009
Posts: 310
Campfire Member
|
Campfire Member
Joined: Jan 2009
Posts: 310 |
Go with thicker recoil lug most of the factory lugs are not straight. They are stamped and are usually bent. Use a go gauge and set the barrel up so you feel it make contact when the bolt goes to full battery.
|
|
|
|
Joined: Nov 2011
Posts: 1,846
Campfire Regular
|
OP
Campfire Regular
Joined: Nov 2011
Posts: 1,846 |
I have a Sharp shooter supply comp. .240 SS lug on its way but still in the air on the headspace, may get dave manson to just send me a go gauge and be done with it.
Lifetime Christian
NRA Lifetime Member
Had rather be judged by 12 than carried by 6.
Your 9mm should expand but my 45 wont shrink.
|
|
|
|
Joined: Nov 2012
Posts: 141
Campfire Member
|
Campfire Member
Joined: Nov 2012
Posts: 141 |
Just an FYI. Copied and pasted out of Otteson's Book Volume II page 71
Each prechambered barrel is screwed and locked into place against a �go� assembly gauge. A �no go� gauge is then inserted to make sure the bolt won�t close. These �assembly,� or �swing� gauges as Savage calls them, look just like headspace gauges, but are exactly .002 inch shorter, the amount the barrel threads seat when the newly-assembled 110 rifles are proofed. Following proof firing, each rifle is rechecked with a set of true headspace gauges.
So you could grind down a go gage and have a SAvage specific assembly gage Or you can just seat it on a go gage and call it good. which is what I have done and will continue to do.
|
|
|
|
Joined: Oct 2008
Posts: 1,628
Campfire Regular
|
Campfire Regular
Joined: Oct 2008
Posts: 1,628 |
Thousands and thousands of Savage 110 rifles are successfully headspaced by their owners using nothing but a piece of factory new brass. Insert a new, unfired 300 RUM case into the chamber and screw the barrel in until it comes to a dead stop against the closed bolt. Tighten the barrel nut and spend the rest of the time concentrating on sight picture and trigger squeeze.
Lock, Stock and Barrel gunworks SLC, Ut USMC 69-73
"This is my rifle, there are many like it but this one is mine. My rifle is my best friend, it is my life."
|
|
|
|
Joined: Nov 2011
Posts: 1,846
Campfire Regular
|
OP
Campfire Regular
Joined: Nov 2011
Posts: 1,846 |
Thanks, was unclear as if should resize the 300rum brass to 338edge before headspacing or leave it 300rum, or if i would matter?
Lifetime Christian
NRA Lifetime Member
Had rather be judged by 12 than carried by 6.
Your 9mm should expand but my 45 wont shrink.
|
|
|
|
Joined: Oct 2008
Posts: 1,628
Campfire Regular
|
Campfire Regular
Joined: Oct 2008
Posts: 1,628 |
The only thing that changes is the neck. It is handled the same as the 338-06 would be with the 25-06, 270 and 30-06.
Lock, Stock and Barrel gunworks SLC, Ut USMC 69-73
"This is my rifle, there are many like it but this one is mine. My rifle is my best friend, it is my life."
|
|
|
|
Joined: Mar 2001
Posts: 12,156
Campfire Outfitter
|
Campfire Outfitter
Joined: Mar 2001
Posts: 12,156 |
Just an FYI. Copied and pasted out of Otteson's Book Volume II page 71
Each prechambered barrel is screwed and locked into place against a �go� assembly gauge. A �no go� gauge is then inserted to make sure the bolt won�t close. These �assembly,� or �swing� gauges as Savage calls them, look just like headspace gauges, but are exactly .002 inch shorter, the amount the barrel threads seat when the newly-assembled 110 rifles are proofed. Following proof firing, each rifle is rechecked with a set of true headspace gauges.
So you could grind down a go gage and have a SAvage specific assembly gage Or you can just seat it on a go gage and call it good. which is what I have done and will continue to do. That may be true, but I can tell you from experience that the factory does not headspace their rifles as tightly as I do at home using a forster go gage. I have my own 22-250 go gage and if you break the barrel nut loose you can screw the barrel down some more with the go gage in the chamber. Brass fired in a couple of factory 22-250's won't chamber after I remove and re-install the barrel using my gage.
|
|
|
|
Joined: Jun 2010
Posts: 863
Campfire Regular
|
Campfire Regular
Joined: Jun 2010
Posts: 863 |
Definately upgrade from the Savage recoil lug , they are tin junk !
Don't forget to have your Liberals spayed or neutered !
|
|
|
|
Joined: May 2008
Posts: 16,540
Campfire Ranger
|
Campfire Ranger
Joined: May 2008
Posts: 16,540 |
I'd use a piece of brass which has been FL sized in your particular sizing die. Why not set the headspace to the dimensions your brass will be when you reload it?
All this said, I'd MUCH rather use a real GO guage.
The Chosin Few November to December 1950, Korea. I'm not one of the Chosin Few but no more remarkable group of Americans ever existed.
|
|
|
|
Joined: Nov 2012
Posts: 141
Campfire Member
|
Campfire Member
Joined: Nov 2012
Posts: 141 |
Well to each their own. In your case you will be reloading. and therefore can set your headspace nearly anywhere you like.
For those that will be shooting factory rounds I don't recommend headspacing off of brass. just set it to the go gage. Factory brass can be as much as .008" under a go gage.
|
|
|
|
607 members (10Glocks, 160user, 12344mag, 10gaugemag, 10ring1, 007FJ, 65 invisible),
2,507
guests, and
1,342
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,203
Posts18,485,345
Members73,966
|
Most Online11,491 Jul 7th, 2023
|
|
|
|