|
Joined: Aug 2007
Posts: 1,636
Campfire Regular
|
OP
Campfire Regular
Joined: Aug 2007
Posts: 1,636 |
I told my wife if I got promoted to SGT. I was going on a bear hunt. Well I got striped, and I are going to Newfoundland adventures for black bear in the spring of 2014. I thought about the taking my cross bow for about a minute and then came to my senses. I have a marlin 1895 that begs to be taken on this hunt and it has never killed anything but paper. I have decided to go with a Meister bullets, 405 gr cast LFP, over about 40grs of 4198. I am looking for about 1700 FPS, but I know that 1600 fps or so will still be plenty of power. I plan to use the XS peep sight as shots are typically close, under 50 yds. I just have to find a load that shoots and get the sights adjusted. I cannot wait to go and getting my marlin ready to go will enjoyable. Any one have some wisdom to impart that would help out? Not going to shoot a small bear, I will come home empty handed before I would do that.
|
|
|
|
Joined: May 2002
Posts: 9,533 Likes: 2
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2002
Posts: 9,533 Likes: 2 |
That load'll do. I know the Beartooth Piledriver Jr at 1650 fps is plenty good bear medicine....
|
|
|
|
Joined: May 2003
Posts: 20,494
Campfire Ranger
|
Campfire Ranger
Joined: May 2003
Posts: 20,494 |
They used to kill buffalo with a 405 at around 1300. Bears should succomb to those loads.
"Keep thy heart with all diligence; for out of it are the issues of life." (Prov 4:23) Brother Keith
|
|
|
|
Joined: Aug 2007
Posts: 1,636
Campfire Regular
|
OP
Campfire Regular
Joined: Aug 2007
Posts: 1,636 |
I figure that speed is not a big requirement, just window dressing. The 45-70 is like a frieght train, so so on the speed but you do not want to be in front of one. it just crushes things!
|
|
|
|
Joined: Mar 2012
Posts: 1,187
Campfire Regular
|
Campfire Regular
Joined: Mar 2012
Posts: 1,187 |
cs2, Will you be hunting over bait stations? The only consideration might be the range you plan to hunt at.
The only cure for life and death is to enjoy the interval. George Santayana
|
|
|
|
Joined: Jan 2001
Posts: 29,921 Likes: 10
Campfire Ranger
|
Campfire Ranger
Joined: Jan 2001
Posts: 29,921 Likes: 10 |
Put 52 to 53 grains of H4895 behind the 405's and go kill stuff. I load about 55 grains to push them up to 1,750 fps, but that comes close to killing on both ends.
Even factory fodder at about 1,300 fps will more than freight train a black bear.
Color me envious and put up some post hunt pics,
Last edited by 1minute; 06/12/13.
1Minute
|
|
|
|
Joined: Aug 2007
Posts: 1,636
Campfire Regular
|
OP
Campfire Regular
Joined: Aug 2007
Posts: 1,636 |
ppine, it will be over bait, 20 to 40yards max range. as to punishing on both ends, well that's why I looking for 1700 at max speed to 1600 fps . Fast enough and power to spare!
|
|
|
|
Joined: Aug 2007
Posts: 1,636
Campfire Regular
|
OP
Campfire Regular
Joined: Aug 2007
Posts: 1,636 |
XS Peep site problem. The windage screws on this site are butter soft. I called the company and told them about it. I am sure they know about already. They are sending me two replacements screws. Any one else noticed this? I like the site, but they really need to improve the quality of the provided screws. Any degree of usage, like sighting in for load developement and they bugger up.
|
|
|
|
Joined: Sep 2001
Posts: 19,084 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2001
Posts: 19,084 Likes: 2 |
I noticed the windage screws on the XS rear sight were a little short.
I went to the local hardware store and bought replacement screws that are a tad longer. Plenty of thread engagement.
|
|
|
|
Joined: Aug 2003
Posts: 17,491
Campfire Ranger
|
Campfire Ranger
Joined: Aug 2003
Posts: 17,491 |
Even a 300-320 at those speeds wouldn't be lacking. The most important detail will be shooting enough of whatever you choose to be very confident in the load. "Placement trumps power," especially since you will be boring a long, narrow hole.
Sometimes, the air you 'let in'matters less than the air you 'let out'.
|
|
|
|
Joined: Aug 2007
Posts: 1,636
Campfire Regular
|
OP
Campfire Regular
Joined: Aug 2007
Posts: 1,636 |
Montana Marine, I bought replacements at the hardware store. They seem to be tapered, and only go in about half way before they get tight. I do not want to force them past that point. At half way in they do not tighten/engage the aperture. They are allen heads also. The hardware store did not have metric sizes in stock to try. Just the standard sizes. I will have to look elsewhere for them. For the time being I will have to use the junk set screws that the are sending as a replacement. I hope to get my hand load sighted in and practice with it. I will shoot a dozen or so shots each time I go to the range. Hope to be with in minute of bear by the early spring of 2014.
|
|
|
|
Joined: Sep 2001
Posts: 19,084 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2001
Posts: 19,084 Likes: 2 |
I bought size 8-32, 1/4". It was a perfect fit. They are the allen socket type. The screws protrude out the sides of the sight base just a tad, less than 1/16". The good thing is there is full thread engagement to keep things tight and strong.
Maybe with the original screws you might have chewed up the threads on the inside of the sight base. If so you could probably chase them with a 8-32 tap and clean them up.
|
|
|
|
Joined: Sep 2001
Posts: 19,084 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2001
Posts: 19,084 Likes: 2 |
I went through this a few years ago, just remembered something.
The repalcement 1/4" screws did protrude out the sides of the sight base a little more than I liked.
After sighting in the rifle, I then filed down the set screws on the inboard side, until they were a length that just slightly protruded from the sight base, when snugged down. It was a little bit tedious, but the result works well, and looks good.
|
|
|
|
Joined: Jan 2013
Posts: 1,348
Campfire Regular
|
Campfire Regular
Joined: Jan 2013
Posts: 1,348 |
I plan on using the 525 Pile Driver's with RL-7. Shots are generally 50 yards and under, so I feel fine with using the giant bullet.
-Matt
"The proof of the whisky is in the drinking, the proof of the rifle is in the shooting."
|
|
|
|
Joined: Nov 2004
Posts: 19,269
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2004
Posts: 19,269 |
Gents, if you loaded a relatively soft(30:1) Lyman 457193,420 grain gg slug over 65 grains FFG blackpowder, the 45/70 would blow daylight through any critter you could draw a bead on for distances that would shock you. The soft alloy penetrates DEEP and expands well. Killers.
Be afraid,be VERY VERY afraid ad triarios redisse My Buddy eh76 speaks authentic Frontier Gibberish!
|
|
|
|
Joined: Aug 2007
Posts: 1,636
Campfire Regular
|
OP
Campfire Regular
Joined: Aug 2007
Posts: 1,636 |
Montana Marine, I'm pretty sure that 8-32-1/4 is what I bought at the hardware store. They still seem to tight going into the sight base. The last thing I want to do is mess it up. I do not have a tap, but I could can buy one to clean up the threads. Thanks for all your help. As to the soft bullet thread, The Meister bullet I am using is rated by them at 9 on a Seaco lead hardness tool. Meister claims that this equal to wheel weights. I think that at 1600 to 1700FPS that bullet will be fine. It is lively off the bench at the range, however I doubt that I will feel it when I have the chance to shoot a bear. What appeture are you using? I am going to try the .190 as the 230 seems to large.
|
|
|
|
Joined: Sep 2001
Posts: 19,084 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2001
Posts: 19,084 Likes: 2 |
I'm using the .190 aperture and it seems like looking through a bay window.
I've never installed the .230 to see how it looks.
|
|
|
|
Joined: Sep 2001
Posts: 19,084 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2001
Posts: 19,084 Likes: 2 |
Getting the 8-32 tap is a good idea. I chased the threads on mine before using the longer screws too.
When I originally sighted mine in, the windage zeroing put the rear sight pretty far to the left, and the set screw on the right actually fell through to the inside of the sight base.
I think those original screws are only 1/16" or so. They look nice recessed and all, but only one or two full threads are engaged at best.
I'm kind of surprised XS doesn't ust a little longer screw from the git go.
|
|
|
|
Joined: Mar 2009
Posts: 407
Campfire Member
|
Campfire Member
Joined: Mar 2009
Posts: 407 |
C2
I'm off to Alaska for black bear in September with my 1895. Was going to look into the Skinner sights but don't know if anyone has any experience with them. Currently using 400 Speers at about 1850 but many say this bullet is a little soft. Good luck on your hunt and congrats on the stripes.
|
|
|
|
Joined: Mar 2009
Posts: 407
Campfire Member
|
Campfire Member
Joined: Mar 2009
Posts: 407 |
Almost forgot, when I go to the range with this rifle I get all kinds of funny looks. It seems many younger shooters have never seen an old fart with a lever action. Most are hesitant to shoot it though..........she kicks just a bit!
|
|
|
|
585 members (160user, 12344mag, 10ring1, 16gage, 10gaugemag, 16penny, 68 invisible),
2,715
guests, and
1,314
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,193,070
Posts18,501,491
Members73,987
|
Most Online11,491 Jul 7th, 2023
|
|
|
|