|
Joined: May 2003
Posts: 742
Campfire Regular
|
OP
Campfire Regular
Joined: May 2003
Posts: 742 |
I have a Weatherby Mk V that I just purchased a B&C Medalist stock for. It has the aluminum bedding block. My question is about glassing. Is it advisable to do so with a bedding block, or a waste of resources.
Want to do this right, but don't want to do more than is needed.
Thanks, 300winnie
|
|
|
|
Joined: Jan 2001
Posts: 29,855
Campfire Ranger
|
Campfire Ranger
Joined: Jan 2001
Posts: 29,855 |
One would like to assume that all is square, but that is not always the case. Just check it.
I have a Mark V that exhibited evidence of stress at the range. The barrel had been floated, but I was suspect on the action. Since ones scope mounts span the action, I thought a bore sighter might provide an answer.
Installed my bore sighter and made note of the cross hair coordinates with the scope at it's highest power. With the sighter still in place, I carefully loosened and tightened the action screws and flexing was quite evident with checks of the bore sighter. Glassed the action in a fully relaxed state. Now nothing moves as one torques down or loosens the screws, and it shoots extremely well.
Heating or inconsistent torque if one assembled or disassembled a rifle for cleaning would obviously affect point of impact.
Not a measure that I can quantify, but I'd speculate it's quite sensitive.
Last edited by 1minute; 02/20/15.
1Minute
|
|
|
|
Joined: May 2014
Posts: 1,122
Campfire Regular
|
Campfire Regular
Joined: May 2014
Posts: 1,122 |
One would like to assume that all is square, but that is not always the case. Just check it.
I have a Mark V that exhibited evidence of stress at the range. The barrel had been floated, but I was suspect on the action. Since ones scope mounts span the action, I thought a bore sighter might provide an answer.
Installed my bore sighter and made note of the cross hair coordinates with the scope at it's highest power. With the sighter still in place, I carefully loosened and tightened the action screws and flexing was quite evident with checks of the bore sighter. Glassed the action in a fully relaxed state. Now nothing moves as one torques down or loosens the screws, and it shoots extremely well.
Heating or inconsistent torque if one assembled or disassembled a rifle for cleaning would obviously affect point of impact.
Not a measure that I can quantify, but I'd speculate it's quite sensitive. I purchased a Bell Carlson with aluminum bedding block for a Zastava Whitworth, (Mouser) The bedding block was not true to my action so I took a dremel and removed enouph material to glass bed it. Mouser actions vary somewhat. The stock you have might be a much better fit being for a weatherby. Shod
The 6.5 Swede, Before Gay Was Ok
|
|
|
|
Joined: Apr 2009
Posts: 2,386
Campfire Regular
|
Campfire Regular
Joined: Apr 2009
Posts: 2,386 |
I skim bed all my stocks with bedding blocks around the recoil lug area.
|
|
|
|
Joined: Dec 2013
Posts: 3,073
Campfire Tracker
|
Campfire Tracker
Joined: Dec 2013
Posts: 3,073 |
Several years ago, I had a 270 built on a Mauser action. The stock was a B&C Medalist with the aluminum bedding block. Long story short, before all was said and done the rifle benefited from being glass bedded.
24HCF in its entirety, is solely responsible for why my children do not have college funds, my mortgage isn't paid-off and why I will never retire early enough to enjoy the remainder of my life.
|
|
|
|
Joined: Dec 2006
Posts: 5,918
Campfire Tracker
|
Campfire Tracker
Joined: Dec 2006
Posts: 5,918 |
When I die I hope I don't start voting democrat.
|
|
|
|
Joined: Feb 2009
Posts: 6,766
Campfire Tracker
|
Campfire Tracker
Joined: Feb 2009
Posts: 6,766 |
I have a Weatherby Mk V that I just purchased a B&C Medalist stock for. It has the aluminum bedding block. My question is about glassing. Is it advisable to do so with a bedding block, or a waste of resources.
Want to do this right, but don't want to do more than is needed.
Thanks, 300winnie shoot it first, then decide.
Guns don't kill people, drivers with cell phones kill people.
|
|
|
|
Joined: Jan 2007
Posts: 11,524
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2007
Posts: 11,524 |
I have a Weatherby Mk V that I just purchased a B&C Medalist stock for. It has the aluminum bedding block. My question is about glassing. Is it advisable to do so with a bedding block, or a waste of resources.
Want to do this right, but don't want to do more than is needed.
Thanks, 300winnie +1 shoot it first, then decide.
|
|
|
|
Joined: Apr 2011
Posts: 12,130
Campfire Outfitter
|
Campfire Outfitter
Joined: Apr 2011
Posts: 12,130 |
I have a Weatherby Mk V that I just purchased a B&C Medalist stock for. It has the aluminum bedding block. My question is about glassing. Is it advisable to do so with a bedding block, or a waste of resources.
Want to do this right, but don't want to do more than is needed.
Thanks, 300winnie shoot it first, then decide. +2 ... If it shoots to your satisfaction without the glass bedding, save the time and $$$'s...
|
|
|
|
Joined: Sep 2010
Posts: 3,998
Campfire Tracker
|
Campfire Tracker
Joined: Sep 2010
Posts: 3,998 |
Rifle actions are mass produced. There are tolerances involved especially in machined parts like actions that are heat treated. There is a chance that your bedding block will fit your action perfectly but a much larger chance that it won't. Shoot it and see if you are happy. If not a little Dremel and drill work and a teaspoon of bedding material is about all it takes to fix it up.
I am continually astounded at how quickly people make up their minds on little evidence or none at all. Jack O'Connor
|
|
|
|
Joined: Aug 2011
Posts: 6,518
Campfire Tracker
|
Campfire Tracker
Joined: Aug 2011
Posts: 6,518 |
I have a Cooper Excaliber that has the B&C stock with the aluminum bedding block. It came bedded from the Factory. Cooper evidently thinks it is necessary.
If we live long enough, we all have regrets. But the ones that nag at us the most are the ones in which we know we had a choice.
Doug
|
|
|
|
Joined: Mar 2014
Posts: 563
Campfire Regular
|
Campfire Regular
Joined: Mar 2014
Posts: 563 |
Bedding a B&C with aluminum took 1/2 moa out of my CZ550.
|
|
|
|
628 members (1beaver_shooter, 10Glocks, 1badf350, 160user, 007FJ, 10gaugemag, 59 invisible),
2,400
guests, and
1,319
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,191,832
Posts18,477,994
Members73,948
|
Most Online11,491 Jul 7th, 2023
|
|
|
|