|
Joined: Nov 2005
Posts: 10,365
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2005
Posts: 10,365 |
Got it,
The factory hole is 180° from zero. Then you will need to redrill the dial
|
|
|
|
Joined: Apr 2009
Posts: 1,972
Campfire Regular
|
Campfire Regular
Joined: Apr 2009
Posts: 1,972 |
Yep,that's what I was thinking.
Thanks for the advice. Just gotta find the right size bit and I'll be in business.
Do you order custom dials or just run the stock dial?
|
|
|
|
Joined: Apr 2005
Posts: 13,762 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Apr 2005
Posts: 13,762 Likes: 1 |
I've had 3 and none of them had the pre-drilled hole in the right spot.
|
|
|
|
Joined: Nov 2005
Posts: 10,365
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2005
Posts: 10,365 |
I had 37 of them and all had the hole in the right spot
Last edited by gemby58; 03/26/15.
|
|
|
|
Joined: Nov 2005
Posts: 10,365
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2005
Posts: 10,365 |
Yep,that's what I was thinking.
Thanks for the advice. Just gotta find the right size bit and I'll be in business.
Do you order custom dials or just run the stock dial? I just run the stock dial, I have a lot of free dial cards, maybe I should send off for them
|
|
|
|
Joined: Nov 2005
Posts: 10,365
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2005
Posts: 10,365 |
Yep,that's what I was thinking.
Thanks for the advice. Just gotta find the right size bit and I'll be in business.
Do you order custom dials or just run the stock dial? if your hole is 180 out then you can use any small drill bit you want I used #48 as that's what fit in the predrilled hole
|
|
|
|
Joined: Feb 2008
Posts: 3,906
Campfire Tracker
|
Campfire Tracker
Joined: Feb 2008
Posts: 3,906 |
Just checked five of mine, only one drilled in the right spot. Ready to go with some #48 bits and a Dremel. Thanks again for the good advice.
Golden............
|
|
|
|
Joined: Feb 2008
Posts: 3,906
Campfire Tracker
|
Campfire Tracker
Joined: Feb 2008
Posts: 3,906 |
I just finished four, drilled the hole two marks right of zero with a #48 bit and used a 5/64" drill end for the pin. After drilling the hole I pushed the end of the 5/64" bit into place then marked it with a fine felt tip pen. Cut to length by holding the keeper end in a small vise grip then using a Dremel cut off wheel. If you cut it too long, grind some off the end and try again.
Thanks for the info in this thread. The drill rod seems to be an easier, more positive system than the ball bearing way.
Golden............
|
|
|
|
Joined: Nov 2005
Posts: 10,365
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2005
Posts: 10,365 |
I just finished four, drilled the hole two marks right of zero with a #48 bit and used a 5/64" drill end for the pin. After drilling the hole I pushed the end of the 5/64" bit into place then marked it with a fine felt tip pen. Cut to length by holding the keeper end in a small vise grip then using a Dremel cut off wheel. If you cut it too long, grind some off the end and try again.
Thanks for the info in this thread. The drill rod seems to be an easier, more positive system than the ball bearing way. That's what were all here on the campfire for, too help each other out. I to think the drill rod is a better way to go than the ball bearing. Glad it worked for you, good shooting.
Last edited by gemby58; 03/28/15.
|
|
|
|
Joined: Apr 2009
Posts: 1,972
Campfire Regular
|
Campfire Regular
Joined: Apr 2009
Posts: 1,972 |
I just finished four, drilled the hole two marks right of zero with a #48 bit and used a 5/64" drill end for the pin. After drilling the hole I pushed the end of the 5/64" bit into place then marked it with a fine felt tip pen. Cut to length by holding the keeper end in a small vise grip then using a Dremel cut off wheel. If you cut it too long, grind some off the end and try again.
Thanks for the info in this thread. The drill rod seems to be an easier, more positive system than the ball bearing way. Spent 15 minutes on my scope tonight. I used the 5/64 bit, then used the dremel and vise grips to make the pin. When I was done, you could spin mine two clicks below zero. Would have been nice if it locked in on the zero, but I drilled it a hair over because I wanted to make sure it would still "zero". Probably enough room to drill another hole and do it right, but at least for now it won't rotate more than once. Overall I'd say it worked well. Thanks to everyone for the advice.
|
|
|
|
Joined: Aug 2005
Posts: 28,258 Likes: 6
Campfire Ranger
|
Campfire Ranger
Joined: Aug 2005
Posts: 28,258 Likes: 6 |
If you run into a situation with the zero stops that don't quite line up with zero, you can always get some of these: http://customturretsystems.com/They work great, and they're cheap, tough, durable.
It is irrelevant what you think. What matters is the TRUTH.
|
|
|
|
Joined: Mar 2008
Posts: 5,335
Campfire Tracker
|
Campfire Tracker
Joined: Mar 2008
Posts: 5,335 |
I just finished four, drilled the hole two marks right of zero with a #48 bit and used a 5/64" drill end for the pin. After drilling the hole I pushed the end of the 5/64" bit into place then marked it with a fine felt tip pen. Cut to length by holding the keeper end in a small vise grip then using a Dremel cut off wheel. If you cut it too long, grind some off the end and try again.
Thanks for the info in this thread. The drill rod seems to be an easier, more positive system than the ball bearing way. Spent 15 minutes on my scope tonight. I used the 5/64 bit, then used the dremel and vise grips to make the pin. When I was done, you could spin mine two clicks below zero. Would have been nice if it locked in on the zero, but I drilled it a hair over because I wanted to make sure it would still "zero". Probably enough room to drill another hole and do it right, but at least for now it won't rotate more than once. Overall I'd say it worked well. Thanks to everyone for the advice. I prefer my stop to dial 1 MOA or so passed zero..its how i set my scopes up.
|
|
|
|
Joined: Sep 2013
Posts: 2,229
Campfire Regular
|
Campfire Regular
Joined: Sep 2013
Posts: 2,229 |
*Master of random precision*
|
|
|
|
Joined: Nov 2007
Posts: 4,911 Likes: 2
Campfire Tracker
|
Campfire Tracker
Joined: Nov 2007
Posts: 4,911 Likes: 2 |
|
|
|
|
Joined: May 2006
Posts: 4,062
Campfire Tracker
|
Campfire Tracker
Joined: May 2006
Posts: 4,062 |
“There is no limit to the amount of good you can do if you don’t care who gets credit.” R. Reagan
|
|
|
|
Joined: Jan 2005
Posts: 57,494
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2005
Posts: 57,494 |
What gives when I need more than a revolution of elevation?
I can't get from 25 to 200 with my 300/221 sub loads without going more than 360?
We can keep Larry Root and all his idiotic blabber and user names on here, but we can't get Ralph back..... Whiskey Tango Foxtrot, over....
|
|
|
|
Joined: Jan 2005
Posts: 57,494
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2005
Posts: 57,494 |
all i would need is the ability to have a firm bottom stop... where I can go back to zero and know which marks apply then...
I do this now, knowing or used to, how many turns up from bottom it took until my home made label applied....
We can keep Larry Root and all his idiotic blabber and user names on here, but we can't get Ralph back..... Whiskey Tango Foxtrot, over....
|
|
|
|
Joined: Feb 2010
Posts: 17,927
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2010
Posts: 17,927 |
Did anyone ever figure out what the factory zero stop is/looks like?
|
|
|
|
Joined: Jul 2009
Posts: 1,045
Campfire Regular
|
Campfire Regular
Joined: Jul 2009
Posts: 1,045 |
The beatings will continue until morale improves
|
|
|
|
Joined: Oct 2009
Posts: 2,019
Campfire Regular
|
Campfire Regular
Joined: Oct 2009
Posts: 2,019 |
One too many hobbies....
|
|
|
|
520 members (1234, 1lesfox, 17CalFan, 007FJ, 01Foreman400, 160user, 56 invisible),
2,403
guests, and
1,234
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,378
Posts18,488,532
Members73,970
|
Most Online11,491 Jul 7th, 2023
|
|
|
|