|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
I know you have to buy a trigger specifically for that gun. I don't even know if they are still made. Timney makes one for the 600 series. DF
|
|
|
|
Joined: Apr 2018
Posts: 8,832 Likes: 15
Campfire Outfitter
|
Campfire Outfitter
Joined: Apr 2018
Posts: 8,832 Likes: 15 |
Ive got a mohawk 600 243 that i am considering going the custom route. But still on the fence...
|
|
|
|
Joined: Apr 2018
Posts: 8,832 Likes: 15
Campfire Outfitter
|
Campfire Outfitter
Joined: Apr 2018
Posts: 8,832 Likes: 15 |
Does a 660 count? Mine was a 243, put a McMillan model 7 handle, timney trigger, had the rear action drilled and tapped, installed Talley’s, factory duped a 8” fluted Hart chambered to 6 ai... one of if not my favorite buck hammer.... I like that a lot! Who built it for you?
|
|
|
|
Joined: Apr 2008
Posts: 668
Campfire Regular
|
Campfire Regular
Joined: Apr 2008
Posts: 668 |
Here is the most recent (and hopefully last) one I built. I trued the action and bolt, fluted the bolt, shortened and reprofiled the shroud, added the 4th hole to use 2-piece mounts, removed the ejection port overhang, slabbed the action, removed the bolt lock down lever and safety knob which I replaced with a smaller more modern design, gunkoted the action, machined a custom adl style triggerguard that put the trigger where it’s supposed to be, stock is a wildcat composites m7 pattern that I had them adl, the barrel is a factory m7 take off in 260. As pictured it weighed in right at 5lbs.
Last edited by bigJ; 06/07/18.
|
|
|
|
Joined: Dec 2008
Posts: 21,228 Likes: 1
Campfire Ranger
|
Campfire Ranger
Joined: Dec 2008
Posts: 21,228 Likes: 1 |
Does a 660 count? Mine was a 243, put a McMillan model 7 handle, timney trigger, had the rear action drilled and tapped, installed Talley’s, factory duped a 8” fluted Hart chambered to 6 ai... one of if not my favorite buck hammer.... I like that a lot! Who built it for you? Steve Kostanich here in Chehalis, built several for me, and will build more...
Ping pong balls for the win. Once you've wrestled everything else in life is easy. Dan Gable I keep my circle small, I’d rather have 4 quarters than 100 pennies.
Ain’t easy havin pals.
|
|
|
|
Joined: Dec 2008
Posts: 21,228 Likes: 1
Campfire Ranger
|
Campfire Ranger
Joined: Dec 2008
Posts: 21,228 Likes: 1 |
Here is the most recent (and hopefully last) one I built. I trued the action and bolt, fluted the bolt, shortened and reprofiled the shroud, added the 4th hole to use 2-piece mounts, removed the ejection port overhang, slabbed the action, removed the bolt lock down lever and safety knob which I replaced with a smaller more modern design, gunkoted the action, machined a custom adl style triggerguard that put the trigger where it’s supposed to be, stock is a wildcat composites m7 pattern that I had them adl, the barrel is a factory m7 take off in 260. As pictured it weighed in right at 5lbs. That horns me up right there.... cool rifle...
Ping pong balls for the win. Once you've wrestled everything else in life is easy. Dan Gable I keep my circle small, I’d rather have 4 quarters than 100 pennies.
Ain’t easy havin pals.
|
|
|
|
Joined: Apr 2013
Posts: 795
Campfire Regular
|
Campfire Regular
Joined: Apr 2013
Posts: 795 |
That’s what I was thinking. I have a 600 .223 in an H&S stock that I might go to whittling on...
Correction, it’s a .222. I could see a 19” 6x45 in its future.
Last edited by Shooter71; 06/08/18.
I’m not an organ donor. I don’t believe in an afterlife, but I’d rather cover my bases in case there is and I need everything. You just never know.
|
|
|
|
Joined: Apr 2018
Posts: 8,832 Likes: 15
Campfire Outfitter
|
Campfire Outfitter
Joined: Apr 2018
Posts: 8,832 Likes: 15 |
Im assuming this crowd would know, does McMillan offer 600 inletting?
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Here is the most recent (and hopefully last) one I built. I trued the action and bolt, fluted the bolt, shortened and reprofiled the shroud, added the 4th hole to use 2-piece mounts, removed the ejection port overhang, slabbed the action, removed the bolt lock down lever and safety knob which I replaced with a smaller more modern design, gunkoted the action, machined a custom adl style triggerguard that put the trigger where it’s supposed to be, stock is a wildcat composites m7 pattern that I had them adl, the barrel is a factory m7 take off in 260. As pictured it weighed in right at 5lbs. I especially like what you did with the trigger guard. Turning a M-700 ADL trigger guard around leaves the trigger sitting way forward, doesn't look that good to me. Your approach is about ideal, IMO. Someone needs to machine your pattern and sell it. The trigger guard issue is the main reason I won't use the McM stock. If I had access to your trigger guard, maybe. DF
|
|
|
|
Joined: Dec 2002
Posts: 32,243 Likes: 2
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Dec 2002
Posts: 32,243 Likes: 2 |
Im assuming this crowd would know, does McMillan offer 600 inletting? Yes, but they only inlet the trigger guard for a reversed 700 ADL trigger guard that, IMO, looks dorky. I have a couple of 600/660 McMillan stocks and reinletted the bottom of one of them to fit the CVMW Bottom metal, as I like the way it looks better than the reversed 700 ADL trigger guard. Anybody who has a 600/660, regardless of the make/model of the stock, would almost certainly prefer the CVMW alloy bottom metal to any other metal or synthetic options out there. The factory plastic units almost always bow in time, a corner than Remington didn't need to cut. Willie Manning's after-market 600/660 bottom metal is the best I've seen and I've probably bought a half-dozen or more of them from him. Willie Manning Coquille Valley Machine Works 541-396-6246 (Oregon)
|
|
|
|
Joined: Dec 2008
Posts: 21,228 Likes: 1
Campfire Ranger
|
Campfire Ranger
Joined: Dec 2008
Posts: 21,228 Likes: 1 |
Im assuming this crowd would know, does McMillan offer 600 inletting? Yes
Ping pong balls for the win. Once you've wrestled everything else in life is easy. Dan Gable I keep my circle small, I’d rather have 4 quarters than 100 pennies.
Ain’t easy havin pals.
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Willie Manning Coquille Valley Machine Works 541-396-6246 (Oregon) +1 My Mohawk wears his bottom metal. Plastic EOM piece is pure junk. DF
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Willie Manning Coquille Valley Machine Works 541-396-6246 (Oregon) +1 My Mohawk wears his bottom metal. Plastic EOM piece is pure junk. DF I would rather have Bigj's trigger guard, McM inletted for it. I think there would be a market. Not sure how much it would cost to set up milling in aluminum or a good cast part properly polished and anodized. Even that part in a good synthetic may not be that bad. The shape is what's so good. The backwards 700 ADL trigger guard, IMO, is ugly enough to keep me from building one. DF
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Willie Manning Coquille Valley Machine Works 541-396-6246 (Oregon) +1 My Mohawk wears his bottom metal. Plastic EOM piece is pure junk. DF I would rather have Bigj's trigger guard, McM inletted for it. I think there would be a market. Not sure how much it would cost to set up milling in aluminum or a good cast part properly polished and anodized. Even that part in a good synthetic may not be that bad. The shape is what's so good. The backwards 700 ADL trigger guard, IMO, is ugly enough to keep me from building one. DF If I was making BigJ's trigger guard, I'd make the foot print the same as the backward M-700 part to avoid a special bottom inlet by McM. DF
|
|
|
|
Joined: Apr 2008
Posts: 668
Campfire Regular
|
Campfire Regular
Joined: Apr 2008
Posts: 668 |
If I was making BigJ's trigger guard, I'd make the foot print the same as the backward M-700 part to avoid a special bottom inlet by McM.
DF
That’s exactly how I did it. The base of my triggerguard is the same dimensions as a factory ADL triggerguard, the triggerguard opening is just moved further forward. The rear screw hole uses the rear action screw as one would expect, the front screw hole is blind (located where the front of the triggerguard hits the base) and tapped for a hidden screw which comes from the inside of the stocks mag well where I used a button head capscrew to secure the front of the trigger guard. I am not setup for production, but someone like Willie Manning could crank something similar out for reasonable money I’m sure. And since he is so well known in 600/660 circles already, that’s who you should approach.
|
|
|
|
Joined: May 2014
Posts: 10,505 Likes: 14
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2014
Posts: 10,505 Likes: 14 |
I have a 350 RM with after market (Douglas) barrel, kevlar stock, steel trigger guard and Timney trigger. It shoots quite well. It's stock needs to be repainted though. It's been hunted.
Last edited by Bugger; 06/08/18.
I prefer classic. Semper Fi I used to run with the hare. Now I'm envious of the tortoise and I do my own stunts but rarely intentionally
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
If I was making BigJ's trigger guard, I'd make the foot print the same as the backward M-700 part to avoid a special bottom inlet by McM.
DF
That’s exactly how I did it. The base of my triggerguard is the same dimensions as a factory ADL triggerguard, the triggerguard opening is just moved further forward. The rear screw hole uses the rear action screw as one would expect, the front screw hole is blind (located where the front of the triggerguard hits the base) and tapped for a hidden screw which comes from the inside of the stocks mag well where I used a button head capscrew to secure the front of the trigger guard. I am not setup for production, but someone like Willie Manning could crank something similar out for reasonable money I’m sure. And since he is so well known in 600/660 circles already, that’s who you should approach. If I had working drawings or detailed photos, I may check with Willie. DF
|
|
|
|
Joined: Dec 2002
Posts: 32,243 Likes: 2
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Dec 2002
Posts: 32,243 Likes: 2 |
If I was making BigJ's trigger guard, I'd make the foot print the same as the backward M-700 part to avoid a special bottom inlet by McM.
DF
That’s exactly how I did it. The base of my triggerguard is the same dimensions as a factory ADL triggerguard, the triggerguard opening is just moved further forward. The rear screw hole uses the rear action screw as one would expect, the front screw hole is blind (located where the front of the triggerguard hits the base) and tapped for a hidden screw which comes from the inside of the stocks mag well where I used a button head capscrew to secure the front of the trigger guard. I am not setup for production, but someone like Willie Manning could crank something similar out for reasonable money I’m sure. And since he is so well known in 600/660 circles already, that’s who you should approach. If I had working drawings or detailed photos, I may check with Willie. DF I wonder how small the market would be for this trigger guard? I have 3 McM Mountain Rifle style stocks inletted for the 600/660 action that are just sitting on a shelf collecting dust because I don't want to use the backward 700 ADL trigger guard and I don't want to reduce their resale value by inletting them for the factory specs plastic or CVMW after-market alloy bottom metal.
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Good question. Willie sells enough of his excellent aluminum bottom metal to keep him making them.
Probably a smaller market for this part. It would be nice to have them available. Programming a CNC would take some doing but cheaper than setting up injection molding. Once set up, ejection molding would be cheaper per unit, just take a lot of units to cover start up costs. CNC would probably be the most reasonable choice for a smaller market. Not sure how Willie makes his.
I’d buy one.
DF
|
|
|
|
Joined: May 2011
Posts: 56,373 Likes: 9
Campfire Kahuna
|
Campfire Kahuna
Joined: May 2011
Posts: 56,373 Likes: 9 |
My 222 wears one of the Coquille aluminum upgrades. Love it. Just want a short compact synthetic stock of some kind.
_______________________________________________________ An 8 dollar driveway boy living in a T-111 shack
LOL
|
|
|
|
591 members (12344mag, 10Glocks, 17CalFan, 10ring1, 1Longbow, 1beaver_shooter, 62 invisible),
2,457
guests, and
1,373
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,194,353
Posts18,527,038
Members74,031
|
Most Online11,491 Jul 7th, 2023
|
|
|
|