I recently purchased a C Sharps 1874 Sharps Hartford in 45/70. What is the general conscience of an all around bullet for general short to mid range target work. I plan to shoot black powder and cast bullets. Right now I have 535 grain but I think they are too heavy for the ranges that I plan to shoot at the present time. Rider
If you're going to cast your own, get a Lyman 457121PH mould and use nothing harder than a 20:1 alloy. Drops a 475gr bullet that is great for targets and hunting out as far as you're comfortable shooting.
Lee makes a mould for the hollow-base 405gr Calvary Carbine bullet, it's the 90268.
Some folks like the 330gr Gould's Bullet. It's a hollow point design. My Shiloh doesn't care for bullets that light so I stick with the 457121PH or heavier.
Ed
"Not in an open forum, where truth has less value than opinions, where all opinions are equally welcome regardless of their origins, rationale, inanity, or truth, where opinions are neither of equal value nor decisive." Ken Howell
It is really hard to beat the Saeco 645 bullet cast from 20-1 for an all-round geaser in the 45-70. It should weigh somewhere close to 480 grains. The big thing to keep in mind with an 18 twist rifle is that twist doesn't always play well with the 1.1 inch bullets.
the most expensive bullet there is isn't worth a plug nickel if it don't go where its supposed to. www.historicshooting.com
500 grain 1881 Saeco grease groove bullet, smaller nose to let you shoot/hunt dirty, less powder compression due to being a three lube groove bullet, still carries plenty of lube to keep fouling under control, accurate as hell and has done nothing but penetrate dead straight on several head of game from friends of mine and me to, in my 45 3-1/4 over 100 grains of Ole Eyensford 2F for 1488 fps it shot length ways though a 55 gal drum filled with water, it sucked the sides of the steel drum closed on exit, no animal could survive that, with 70gr Old Eyensford under it velocity will be 1300 fps, a very formidable load for the 45-70.
In the 45-70 cast with 20 or 30 to 1 alloy you'll shoot through any game animal in this country of Alaska, round nose bullets simply work.
I always favored the Ideal now Lyman 457-121 PH. It was originally developed by Harry Pope and I shot it first in my 86 Winchester and on through the years. It's a little undersized for the .450-.458 bore groove but with 1/20 alloy it obturate well and for midrange accuracy it's hard to beat. It's a great hunting bullet with black powder loads that will let you shoot with out fouling control that a bore rider won't let you do.
I sent a print to Tom at accurate moulds to make a twin to the 121 that is proper for the .450/.458 bore groove and I have shot this bullet using my .45-70 and the .45-90 out to 1026 yards in Montana with some good breezes and hit the iron 8 out of 10 shots.
Did you have Tom cut yours at .458'? I'm thinking about an iron single-cavity for both my Shiloh 1874 45-70 and my custom .458 Win.
Thanks,
Ed
"Not in an open forum, where truth has less value than opinions, where all opinions are equally welcome regardless of their origins, rationale, inanity, or truth, where opinions are neither of equal value nor decisive." Ken Howell
I tried a 385 RN mould but kept going back to the Lee 405 HB in my Trapdoors. I just liked the flat nose of the Lee better for hunting. Not much there so far as velocity to start with so I figure the flat nose will impart a little more energy to a deer. I think I still have the Rapine 385 and two of the Lees.
I tried a 385 RN mould but kept going back to the Lee 405 HB in my Trapdoors. I just liked the flat nose of the Lee better for hunting. Not much there so far as velocity to start with so I figure the flat nose will impart a little more energy to a deer. I think I still have the Rapine 385 and two of the Lees.
Mr. Strayer,
That Lyman 457121-PH also has a flat nose, and, while not quite as large a flat nose as the 405 Gov bullet, it kills very, very well.
As a big believer in large meplats for striking effects, size does matter!
Ed
"Not in an open forum, where truth has less value than opinions, where all opinions are equally welcome regardless of their origins, rationale, inanity, or truth, where opinions are neither of equal value nor decisive." Ken Howell
Ed, The print I sent Tom was .458 and the mould came as the print at .458. I don't know what happened with his print at .46 Here is a 5 shot target when I got the mould shot at 135 yards in my yard with a scoped .45-90.
Nice work!
I believe I'll have Tom carve one out for me, too.
Thanks,
Ed
"Not in an open forum, where truth has less value than opinions, where all opinions are equally welcome regardless of their origins, rationale, inanity, or truth, where opinions are neither of equal value nor decisive." Ken Howell
Still say the saeco 645 mould is about as good as it gets for a general use bullet in the 45-70. The bugger shoots well to 1000, and will shoot nice tight groups all the way back to 200 yards. 480 grs cast from 20-1. Probably wouldn't make a bad hunting bullet if one is into shooting grease groove bullets.
the most expensive bullet there is isn't worth a plug nickel if it don't go where its supposed to. www.historicshooting.com
Don, some of us never got into smoking dope as kids because we couldn't handle rolling papers. So...it's greasers for us!
Ed
"Not in an open forum, where truth has less value than opinions, where all opinions are equally welcome regardless of their origins, rationale, inanity, or truth, where opinions are neither of equal value nor decisive." Ken Howell
Never messed with that [bleep] either But did a little with bull durham But shooting patched is the best way to go But if a person lacks two oposible thumbs then the 645 is the way to go in a 45-70 😀
the most expensive bullet there is isn't worth a plug nickel if it don't go where its supposed to. www.historicshooting.com
LOL, Ranch13, does the nose of that 645 Saeco look like a 535gr Postell or 540gr Creedmoor? i've never saw one, Bill said the old 1881 Saeco round nose has flew well to 1000 yards for folks too, and we all know how it and the big Lyman 520gr round nose perform on heavy game.
It looks more like an original 45 colt bullet One time after Bill and I had a visit about stuff shortly after he got that 20 twist gun he dug around and came up with a 645 mould and when he called back he was excited
the most expensive bullet there is isn't worth a plug nickel if it don't go where its supposed to. www.historicshooting.com
Nice, i'm going to guess mid length roundish nose with small meplat? if so one could cast it soft and knock the crap out of deer sized game animals, Thanks for the info.