Well, I can't find it easily........But........
Turns out I was smart enough to paste it into my own document for future use. It was done by a gentleman by the name of John Valentine.
Originally posted on Benchrest Central:
Using The Lee Collet Die.
I started using Lee collet dies when they first came on the market and have found that they are very good for the purposes for which they were designed .
I have found that there is a lack of understanding of how to use the die properly and as a result people fail to see the advantages that the die can deliver over standard neck sizing dies.
This is not the fault of the product , it is just a lack of understanding of how the die works and what it will feel like when you operate the press correctly.
Standard dies use a neck expanding ball on the decapping rod and size by extruding the neck through a hole and then drag the expander ball back through the inside neck.
The collet die achieves neck sizing by using a split collet to squeeze the outside of the case neck onto a central mandrel which has the decapping pin in it�s base .
One advantage is that there is no stretching or drawing action on the brass.
The inside neck diameter is controlled by the diameter of the mandrel and to some extent by the amount of adjustment of the die and the pressure applied to the press .
This results in less misalignment than can occur in standard dies because of any uneven neck wall thickness in the cases .
Cases will last longer in the neck area and require less trimming. If cases have very uneven neck wall thickness then this can cause problems for the collet die they definitely work smoother and more accurately with neck turned cases but it is not essential.
When you first receive the die unscrew the top cap and pull it apart check that everything is there also that the splits in the collet have nothing stuck in them then inspect the tapered surface on the top end of the collet and the internal taper of the insert to make sure there are no metal burs that might cause it to jamb.
Next get some good quality high pressure grease and put a smear onto the tapered surface of the collet .
Put it back together and screw it into the press just a few threads for now . The best type of press for this die is a press of moderate compound leverage that travels over centre .
Over centre means that when the ram reaches its full travel up it will stop and come back down a tiny amount even though the movement on the handle is continued through to the stop .
eg. is an RCBS Rockchucker.
This arrangement gives the best feel for a collet die sizing operation.
Place the shell holder in the ram and bring the ram up to full height then screw the die down until the collet skirt just touches on the shell holder , then lower the ram .
Take a case to be sized that has a clean neck inside and out and the mouth chamfered and place it in the shell holder.
Raise the ram gently feeling for resistance if none , lower the ram.
Screw the die down a bit at a time .
If you get lock up ( ram stops before going over centre) before the correct position is found then back it off and make sure the collet is loose and not jammed up in the die before continuing then raise the ram feeling for any resistance , keep repeating this until you feel the press handle resist against the case neck just at the top of the stroke as the press goes over centre and the handle kinder locks in place .
This takes much less force than a standard die and most people don�t believe any sizing has taken place .
Take the case out and try a projectile of the correct caliber to see how much sizing has taken place.
If it�s still too loose adjust the die down one eighth of a turn lock it finger tight only and try again .
Once the die is near the correct sizing position it takes very little movement of the die to achieve changes in neck seating tension .
This is where most people come undone , they move the die up and down too much and it either locks up or doesn�t size at all .
It will still size a case locking it up but you have no control over how much pressure is applied and some people lean on the press handle to the point of damaging the die. A press like the RCBS Rockchucker , that goes over centre each time gives you a definite stopping point for the ram and the pressure that you apply .
There is a small sweet spot for correct collet die adjustment and you must find it , once found , how sweet it is ! Advantages : With a press that travels over centre it is possible to adjust the neck seating tension within a limited zone. No lubricant is required on the case necks during sizing .
There are some other advantages but I will leave you the pleasure of discovering them .
One disadvantage that I have found with the collet die is that it needs good vertical alignment of the case as it enters the die or case damage may result so go slowly.
This is not a problem once you learn how to use them.
The harder the brass is the more spring back it will have so very hard brass will exhibit less sizing than soft brass because it will spring away from the mandrel more. If this is happening to excess then use new cases or anneal the necks.
Freshly annealed brass can drag on the mandrel a bit in certain cases because it will spring back less and result in a tighter size diameter.
I have experienced it. I always use some dry lube on the inside and outside if I get any draging effect . Normally you dont need lube.
I make up a special batch 1/3 Fine Moly powder. 1/3 Pure graphite. 1/3 Aluminiumised lock graphite. Rub your fingers around the neck and It sticks very well to the necks by just dipping it in and out and tapping it to clear the inside neck . After a few cases it coats up the mandrel .
Other dry lubricants would work also.
Use the same process for normal neck sizing also.
I noticed a definite improvement in the accuracy of my 22-250Rem. as soon as I started using a Lee collet die instead of my original standard neck die.
Readers are encouraged to utilise the benefits of responsible reloading at all times. Although the author has taken care in the writing of these articles no responsibility can be taken by the author or publisher as a result of the use of this information.
John Valentine. � 21/01/2002.
An RCBS Rockchucker is very good for a Lee collet die.
Are you sizing to a point where the press goes over center and kinda locks the handle inplace . Just like BJS6 is doing.
Your post does not give me that impression .
If you are using just handle pressure against the die without it going over center then you have no controll over the size pressure , no stopping point .
If this is the case then go back and readjust the die a small amount at a time untill it starts to go over center while resizing a case and the handle locks in place.
Then try a projectile in the case . If it needs extra sizing from that point only move the die a very small amount at a time.
If it stops going over center you have gone past the sweet spot.
Edit to add: found it on the new layout finally:
http://benchrest.com/showthread.php?48671-lee-collet-dies-neck-tension/page2&highlight=collet
