|
Joined: Jan 2001
Posts: 28,399 Likes: 1
Campfire Ranger
|
OP
Campfire Ranger
Joined: Jan 2001
Posts: 28,399 Likes: 1 |
Thought I would try my hand at destroying reshaping a Ruger factory 10/22 carbine stock and staining it a darker, more walnut like color.
I have read that when staining birch it takes on a mottled look so does anyone have any special tips or gotchas or recommendations for stains for this? Not trying to get it really authentic walnut looking but just trying to give it a more uniform darker look than that light color that comes from the factory.
This is a one time project so I'd appreciate keeping the supplies simple, if I got a quart of this and a pint of that and a half gallon of the other, 90% would go to waste on a garage shelf.
Gunnery, gunnery, gunnery. Hit the target, all else is twaddle!
|
|
|
|
Joined: Feb 2001
Posts: 50,643 Likes: 1
Campfire Kahuna
|
Campfire Kahuna
Joined: Feb 2001
Posts: 50,643 Likes: 1 |
Before staining apply a wash of very thin shellac. It will go into the areas that absorb faster than the others and slow stain take-up. It will allow a simple finish of any kind (almost any) to be applied on top. Quick, simple, and appropriate for the job.
Mark Begich, Joaquin Jackson, and Heller resistance... Three huge reasons to worry about the NRA.
|
|
|
|
Joined: May 2006
Posts: 430
Campfire Member
|
Campfire Member
Joined: May 2006
Posts: 430 |
Min-Wax makes a "pre stain" that you put on before staining. Dosen't do bad to even out the shading.
|
|
|
|
Joined: Feb 2001
Posts: 50,643 Likes: 1
Campfire Kahuna
|
Campfire Kahuna
Joined: Feb 2001
Posts: 50,643 Likes: 1 |
Min-Wax pre-stain is a thinned wash of shellac at a much higher price...
Mark Begich, Joaquin Jackson, and Heller resistance... Three huge reasons to worry about the NRA.
|
|
|
|
Joined: Jan 2001
Posts: 28,399 Likes: 1
Campfire Ranger
|
OP
Campfire Ranger
Joined: Jan 2001
Posts: 28,399 Likes: 1 |
Just to verify the obvious, "thinned shellac" would be thinned with mineral spirits, right? Obviously I don't do a lot of stock work or finishing of any kind so I need to ask the basic questions.
Gunnery, gunnery, gunnery. Hit the target, all else is twaddle!
|
|
|
|
Joined: Jul 2009
Posts: 369
Campfire Member
|
Campfire Member
Joined: Jul 2009
Posts: 369 |
Walnut Polystain is what the factories use. Spray on until you get the color you want.
|
|
|
|
Joined: Nov 2005
Posts: 23,114 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2005
Posts: 23,114 Likes: 2 |
Just to verify the obvious, "thinned shellac" would be thinned with mineral spirits, right? Obviously I don't do a lot of stock work or finishing of any kind so I need to ask the basic questions. No. Alcohol is the solvent for shellac.
"You can lead a man to logic, but you cannot make him think." Joe Harz "Always certain, often right." Keith McCafferty
|
|
|
|
Joined: Jan 2001
Posts: 28,399 Likes: 1
Campfire Ranger
|
OP
Campfire Ranger
Joined: Jan 2001
Posts: 28,399 Likes: 1 |
Thanks - you can see why I'm asking the beginner questions.
Gunnery, gunnery, gunnery. Hit the target, all else is twaddle!
|
|
|
|
594 members (10gaugeman, 1936M71, 10ring1, 10gaugemag, 160user, 12344mag, 66 invisible),
2,623
guests, and
1,155
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,857
Posts18,497,077
Members73,979
|
Most Online11,491 Jul 7th, 2023
|
|
|
|