|
Joined: Feb 2010
Posts: 1,867
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2010
Posts: 1,867 |
Friend of mine has a "B" prefix 700 in 270, and it went off unexpectedly the other day while he was hunting as he pushed the safety from Safe to Fire. It has the old trigger design (which I own quite a few of and have never had any trouble out of) and he had read about the issues some have had with them.
I have a Timney trigger here that was installed by me in a varmint rifle, used briefly and removed when the purchaser of the rifle didn't want it. I thought the only way my friend would ever have confidence in the rifle again was to completely replace the trigger group, so I installed the Timney into his rifle last night.
After installing the new trigger, I bounce tested it and was able to make the rifle "fire" when the safety was taken off. Also, I was able to make it "fire" a couple of times at bolt closure. I disassembled the firing pin group and cleaned everything, nothing appears damaged or looks out of place.
What is the proper way to handle getting his rifle repaired? A reputable gunsmith or send it back to Remington? Any recommendations would be appreciated.
Thanks.
God is great, beer is good, and people are crazy...
|
|
|
|
Joined: Jan 2008
Posts: 4,219
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2008
Posts: 4,219 |
What weight is the timney set for?
|
|
|
|
Joined: Nov 2013
Posts: 3,804
Campfire Tracker
|
Campfire Tracker
Joined: Nov 2013
Posts: 3,804 |
sounds like the timney may just need the sear engagement adjusted a bit, it's the screw on the back of the trigger, also the pull weight may be too light
|
|
|
|
Joined: Oct 2009
Posts: 1,742
Campfire Regular
|
Campfire Regular
Joined: Oct 2009
Posts: 1,742 |
Agree with attempt to adjust trigger. You don't have enough sear engagement.
|
|
|
|
Joined: Mar 2011
Posts: 2,601
Campfire Regular
|
Campfire Regular
Joined: Mar 2011
Posts: 2,601 |
sounds like the timney may just need the sear engagement adjusted a bit, it's the screw on the back of the trigger, also the pull weight may be too light Yep. Bet that trigger is pretty light right now.
Nut
Experience hath shewn, that even under the best forms of government those entrusted with power have, in time, and by slow operations, perverted it into tyranny.
Thomas Jefferson
|
|
|
|
Joined: Jun 2003
Posts: 42,636 Likes: 2
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2003
Posts: 42,636 Likes: 2 |
Friend of mine has a "B" prefix 700 in 270, and it went off unexpectedly the other day while he was hunting as he pushed the safety from Safe to Fire. It has the old trigger design (which I own quite a few of and have never had any trouble out of) and he had read about the issues some have had with them.
A good principle to guide me through life: “This is all I have come to expect, standard lackluster performance. Trust nothing, believe no one and realize it will only get worse…”
|
|
|
|
Joined: Dec 2012
Posts: 100
Campfire Member
|
Campfire Member
Joined: Dec 2012
Posts: 100 |
absolutely sear . I have a rather old model 110 was doing same thing
|
|
|
|
Joined: Sep 2004
Posts: 29,383
Campfire Ranger
|
Campfire Ranger
Joined: Sep 2004
Posts: 29,383 |
Friend of mine has a "B" prefix 700 in 270, and it went off unexpectedly the other day while he was hunting as he pushed the safety from Safe to Fire. It has the old trigger design (which I own quite a few of and have never had any trouble out of) and he had read about the issues some have had with them.
I have a Timney trigger here that was installed by me in a varmint rifle, used briefly and removed when the purchaser of the rifle didn't want it. I thought the only way my friend would ever have confidence in the rifle again was to completely replace the trigger group, so I installed the Timney into his rifle last night.
After installing the new trigger, I bounce tested it and was able to make the rifle "fire" when the safety was taken off. Also, I was able to make it "fire" a couple of times at bolt closure. I disassembled the firing pin group and cleaned everything, nothing appears damaged or looks out of place.
What is the proper way to handle getting his rifle repaired? A reputable gunsmith or send it back to Remington? Any recommendations would be appreciated.
Thanks. Turn the sear adjustment screw 1/4 turn at a time counterclockwise until it passes the "slam bolt and bounce test".
|
|
|
|
Joined: Feb 2010
Posts: 1,867
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2010
Posts: 1,867 |
Thanks for the suggestions, I'll check the sear adjustment this evening.
Anyone care to speculate why the Timney did fine in the varmint rifle and exhibits the same signs as the factory trigger did in the suspect rifle? Kind of makes me wonder if it is something outside the trigger group.
Thanks again.
God is great, beer is good, and people are crazy...
|
|
|
|
Joined: Oct 2009
Posts: 1,742
Campfire Regular
|
Campfire Regular
Joined: Oct 2009
Posts: 1,742 |
The trigger interface is slightly different in each rifle. It's not uncommon to need adjusting when swapping.
|
|
|
|
Joined: Feb 2004
Posts: 2,098
Campfire Regular
|
Campfire Regular
Joined: Feb 2004
Posts: 2,098 |
Also clean the entire trigger assembly with carb cleaner or something like it and don't lube it. Rick.
|
|
|
|
Joined: Jan 2007
Posts: 35,900
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jan 2007
Posts: 35,900 |
Thanks for the suggestions, I'll check the sear adjustment this evening.
Anyone care to speculate why the Timney did fine in the varmint rifle and exhibits the same signs as the factory trigger did in the suspect rifle? Kind of makes me wonder if it is something outside the trigger group.
Thanks again. CFVA I suppose no portion of the trigger housing or trigger are bearing on any portion of the stock when screws are tightened,right?
The 280 Remington is overbore.
The 7 Rem Mag is over bore.
|
|
|
|
Joined: Feb 2010
Posts: 1,867
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2010
Posts: 1,867 |
Thanks to everyone.
Bob - I did have to relieve a bit of wood to allow for the trigger adjustment screw on the Timney, but otherwise I haven't found any interference.
Thanks again.
God is great, beer is good, and people are crazy...
|
|
|
|
Joined: Jan 2007
Posts: 35,900
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jan 2007
Posts: 35,900 |
The 280 Remington is overbore.
The 7 Rem Mag is over bore.
|
|
|
|
Joined: Nov 2013
Posts: 3,804
Campfire Tracker
|
Campfire Tracker
Joined: Nov 2013
Posts: 3,804 |
The trigger interface is slightly different in each rifle. It's not uncommon to need adjusting when swapping. Also clean the entire trigger assembly with carb cleaner or something like it and don't lube it. Rick. This
|
|
|
|
Joined: Jan 2001
Posts: 59,180 Likes: 3
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2001
Posts: 59,180 Likes: 3 |
A Remington with a trigger issue??? Oh, SAY it ain't SOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOOO!! (sorry, couldn't resist)...
Ex- USN (SS) '66-'69 Pro-Constitution. LET'S GO BRANDON!!!
|
|
|
|
Joined: Feb 2010
Posts: 1,867
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2010
Posts: 1,867 |
Knew that was coming, just didn't know from who!
I adjusted the sear engagement last night, and it would still fail occasionally on bolt closure. I noticed the trigger shoe wasn't resetting itself if the muzzle was pointed upward, so I adjusted the trigger weight screw until it had a positive spring reset pressure. After doing that, all is good in the world. Just for reference, the Timney was 3 lbs out of the box, and is set at 5.5 lbs now. Still crisp and doesn't feel all that heavy, but it's safe.
Thanks again to everyone.
God is great, beer is good, and people are crazy...
|
|
|
|
Joined: Aug 2002
Posts: 19,129 Likes: 2
Campfire Ranger
|
Campfire Ranger
Joined: Aug 2002
Posts: 19,129 Likes: 2 |
Also clean the entire trigger assembly with carb cleaner or something like it and don't lube it. The Timney web page says to lube with lighter fluid. miles
Look out for number 1, don't step in number 2.
|
|
|
|
Joined: Mar 2005
Posts: 4,999
Campfire Tracker
|
Campfire Tracker
Joined: Mar 2005
Posts: 4,999 |
.... I noticed the trigger shoe wasn't resetting itself if the muzzle was pointed upward.... If you really have a trigger shoe installed on your Timney, that is probably most of your problem.
|
|
|
|
Joined: Nov 2013
Posts: 28,925 Likes: 20
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2013
Posts: 28,925 Likes: 20 |
Be very careful performing the bolt-slam test to avoid breaking off the handle.
Come on, you know you were thinking it!
CFVA: Good on you for helping out a pal.
What fresh Hell is this?
|
|
|
|
605 members (12344mag, 10gaugemag, 160user, 06hunter59, 16gage, 19rabbit52, 64 invisible),
2,813
guests, and
1,285
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,193,644
Posts18,512,419
Members74,010
|
Most Online11,491 Jul 7th, 2023
|
|
|
|