|
Joined: Sep 2008
Posts: 1,036
Campfire Regular
|
OP
Campfire Regular
Joined: Sep 2008
Posts: 1,036 |
Any guess what the problem might be with the bolt release on a Rem 700 action? I took the bolt out to scope the rifle and had trouble getting the release to release the bolt, finally it released the bolt but when I put bolt back in action could not get release to work so bolt simply slides in & out of the action. Thanks
|
|
|
|
Joined: Feb 2001
Posts: 50,669 Likes: 2
Campfire Kahuna
|
Campfire Kahuna
Joined: Feb 2001
Posts: 50,669 Likes: 2 |
The 700 bolt release is very prone to binding due to the parts rubbing on the inside of the stock. Pull the action out of the stock and look at how simple the release is... it is possible gunk got into the lever pinned in the action rather than the linkage... WD40 is great for causing that.
Mark Begich, Joaquin Jackson, and Heller resistance... Three huge reasons to worry about the NRA.
|
|
|
|
Joined: Sep 2008
Posts: 1,036
Campfire Regular
|
OP
Campfire Regular
Joined: Sep 2008
Posts: 1,036 |
|
|
|
|
Joined: May 2014
Posts: 10,505 Likes: 14
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2014
Posts: 10,505 Likes: 14 |
WD40 is a perfect product if you want build up of gunk. It has no proper usage on a gun of any sort.
I prefer classic. Semper Fi I used to run with the hare. Now I'm envious of the tortoise and I do my own stunts but rarely intentionally
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Also check to see if the bolt release tab is binding in the bolt stop groove. Slightly bending the tab can do wonders if it's binding.
Sitka is right about stuff like WD-40 gunking up the works, causing the bolt stop to stick. You about gotta take it apart and sometimes it takes steel wool, etc. to get that varnish off the parts. Blasting it with brake cleaner, etc. usually doesn't cut that stuff.
Use WD-40 on farm equipment, keep it away from padlocks, guns, anything with small parts that interact.
DF
|
|
|
|
Joined: Feb 2010
Posts: 15,829 Likes: 9
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2010
Posts: 15,829 Likes: 9 |
Also check to see if the bolt release tab is binding in the bolt stop groove. Slightly bending the tab can do wonders if it's binding.
Sitka is right about stuff like WD-40 gunking up the works, causing the bolt stop to stick. You about gotta take it apart and sometimes it takes steel wool, etc. to get that varnish off the parts. Blasting it with brake cleaner, etc. usually doesn't cut that stuff.
Use WD-40 on farm equipment, keep it away from padlocks, guns, anything with small parts that interact.
DF I've bought several Remington 721's, 722's and 700's with that problem and a good spray down with one of the crud cutter formulations with a little application tube while you work the release will usually free it up. You have to get it down in the little slot where the bolt release pivots and underneath the slider alongside the trigger housing. It make take several applications and be sure to wear your safety glasses/googles because those little nooks and crannies tend to spit the stuff back at you.
NRA Life,Endowment,Patron or Benefactor since '72.
|
|
|
|
Joined: May 2010
Posts: 7,375
Campfire Tracker
|
Campfire Tracker
Joined: May 2010
Posts: 7,375 |
The 700 bolt release is very prone to binding due to the parts rubbing on the inside of the stock. Pull the action out of the stock and look at how simple the release is... it is possible gunk got into the lever pinned in the action rather than the linkage... WD40 is great for causing that. Yep, that's also been my experience....
"When the going gets weird, the weird turn pro." Hunter S. Thompson
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Also check to see if the bolt release tab is binding in the bolt stop groove. Slightly bending the tab can do wonders if it's binding.
Sitka is right about stuff like WD-40 gunking up the works, causing the bolt stop to stick. You about gotta take it apart and sometimes it takes steel wool, etc. to get that varnish off the parts. Blasting it with brake cleaner, etc. usually doesn't cut that stuff.
Use WD-40 on farm equipment, keep it away from padlocks, guns, anything with small parts that interact.
DF I've bought several Remington 721's, 722's and 700's with that problem and a good spray down with one of the crud cutter formulations with a little application tube while you work the release will usually free it up. You have to get it down in the little slot where the bolt release pivots and underneath the slider alongside the trigger housing. It make take several applications and be sure to wear your safety glasses/googles because those little nooks and crannies tend to spit the stuff back at you. I'd not be satisfied until I had taken it apart, cleaned each piece and put it back together. Then, I'd know what I had. Just me. DF
|
|
|
|
Joined: Apr 2007
Posts: 3,362
Campfire Tracker
|
Campfire Tracker
Joined: Apr 2007
Posts: 3,362 |
Mine was due to bedding compound in the recess the bolt release is intended to fill. Carved some out and it worked just like before.
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Mine was due to bedding compound in the recess the bolt release is intended to fill. Carved some out and it worked just like before. BTDT... DF
|
|
|
|
Joined: Sep 2008
Posts: 1,036
Campfire Regular
|
OP
Campfire Regular
Joined: Sep 2008
Posts: 1,036 |
What would be your guess with a new custom gun? I have taken it out of the stock & everything works good but I have not found where release is binding against the stock. 2nd question, If you had never seen a McMillin stock how would you know if it was or not? BTW I don't use WD-40 on anything other than bolts & nuts.
Last edited by DLALLDER; 05/19/16.
|
|
|
|
Joined: Oct 2009
Posts: 5,834
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2009
Posts: 5,834 |
What would be your guess with a new custom gun? I have taken it out of the stock & everything works good but I have not found where release is binding against the stock. 2nd question, If you had never seen a McMillin stock how would you know if it was or not? BTW I don't use WD-40 on anything other than bolts & nuts. Put a thin coat of inletting black or Prussian blue on the bolt stop. Put the barreled action back in the stock and look for signs of the inletting black or Prussian blue on the internal surfaces of the stock. FWIW, I have several McM stocks and have yet to have an issue with the bolt stop not working. My next build(d) will see there way to having side bolt releases installed, though.
I never thought I'd grow up to be a grumpy old man, but I did, and I'm killin' it.
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
The side bolt release is a nice touch.
DF
|
|
|
|
Joined: Mar 2001
Posts: 12,166
Campfire Outfitter
|
Campfire Outfitter
Joined: Mar 2001
Posts: 12,166 |
What would be your guess with a new custom gun? I have taken it out of the stock & everything works good but I have not found where release is binding against the stock. 2nd question, If you had never seen a McMillin stock how would you know if it was or not? BTW I don't use WD-40 on anything other than bolts & nuts. Is it a stock remington trigger or an aftermarket trigger? Jewell's have a habit of binding if the stock isn't relieved, they're wider than the factory trigger and the bolt release linkage touches the stock if the stock isn't relieved. It's an easy fix. If it works out of the stock but binds when you put it in the stock then it's rubbing. Figure out where it's at sand a little bit of the stock.
|
|
|
|
Joined: Jan 2001
Posts: 59,180 Likes: 3
Campfire Kahuna
|
Campfire Kahuna
Joined: Jan 2001
Posts: 59,180 Likes: 3 |
WD40 is a perfect product if you want build up of gunk. It has no proper usage on a gun of any sort.
I could not POSSIBLY agree more...
Ex- USN (SS) '66-'69 Pro-Constitution. LET'S GO BRANDON!!!
|
|
|
|
Joined: Sep 2008
Posts: 1,036
Campfire Regular
|
OP
Campfire Regular
Joined: Sep 2008
Posts: 1,036 |
The release is like a Remington but the trigger is a Timney. Have found out that with the trigger guard snugged down release sticks---with triger guard loose or removed release works as it should. Still have not found where it is binding. Give me your suggestion!!!
|
|
|
|
Joined: Mar 2005
Posts: 17,527
Campfire Ranger
|
Campfire Ranger
Joined: Mar 2005
Posts: 17,527 |
I got tired of playing that game, and had side releases installed on my only two remingtons.
PS, wd40 is good stuff on battery terminals.
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
I like Ballistol. It's non petroleum and doesn't gum up. It even works with BP, something that the petro based solvents won't do. The cowboy action BP shooters mix it with water to make their "pigeon milk" concoction. And, Ballistol won't varnish up or gum up. It does well with leather and wood. Almost a "cure all", snake oil type product... The Germans developed it many years ago, it's been around longer than WD-40. DF
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
The release is like a Remington but the trigger is a Timney. Have found out that with the trigger guard snugged down release sticks---with triger guard loose or removed release works as it should. Still have not found where it is binding. Give me your suggestion!!! Classic binding of a Timney by the trigger guard. Put the bottom metal in a padded vice, trigger guard down. Take your Dremel and "mill" a slot on each side of the trigger opening to accommodate the wider Timney. I do this all the time. The Timney sticks down farther and is wider than the factory trigger. That should fix it. DF
|
|
|
|
Joined: Nov 2010
Posts: 37,229 Likes: 9
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,229 Likes: 9 |
Just mill the slot deep enough to accommodate the trigger, not deep enough to see the cut from inside the trigger guard.
Probably 3/16" wide and about that deep, both sides. Hold the bottom metal next to the action and scribe with a Sharpie the area where the trigger interacts with the bottom metal and cut out that area.
DF
|
|
|
|
504 members (1OntarioJim, 10gaugemag, 160user, 1Longbow, 1badf350, 17CalFan, 45 invisible),
2,322
guests, and
1,219
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,194,333
Posts18,526,724
Members74,031
|
Most Online11,491 Jul 7th, 2023
|
|
|
|