|
Joined: Mar 2004
Posts: 20,827
Campfire Ranger
|
OP
Campfire Ranger
Joined: Mar 2004
Posts: 20,827 |
I recently had a back surgery that has offered a good bit of relief... I have been digging out the gun safe and fooling with several rifles and pistols I have not used in years. The Low Wall is probably my all time favorite.
I remember it clover leafing 3 shots at 100 yards. Now with the same loads it puts 2 real close but the 3rd shot always seems to wander an inch or so.... the fore end does not let a dollar bill slide past in the very front now. I thought that it used to but it has been several years... the only thing I remember for sure are the bragging sized groups.
Round file/sand enough wood to free float... bedding under the hanging bar??? Other Low Wall refinement suggestions?
TX John
Please don't feed the trolls!
|
|
|
|
Joined: May 2011
Posts: 15,886
Campfire Ranger
|
Campfire Ranger
Joined: May 2011
Posts: 15,886 |
Get in touch with Steve Zihn, here on the fire. szihn is his screen name, I believe.
There are 2 rules to success:
1. Never tell everything that you know.
|
|
|
|
Joined: Mar 2004
Posts: 20,827
Campfire Ranger
|
OP
Campfire Ranger
Joined: Mar 2004
Posts: 20,827 |
Please don't feed the trolls!
|
|
|
|
Joined: May 2002
Posts: 10,635
Campfire Outfitter
|
Campfire Outfitter
Joined: May 2002
Posts: 10,635 |
If your low wall is the same as the Miroku made 1885s I am familiar with, the forearm is fastened to a hanger completely independent of the barrel. Relieving the channel to free float it couldn't be simpler, and shouldn't require the services of a gunsmith.
Paul
Stupidity has its way, while its cousin, evil, runs rampant.
|
|
|
|
Joined: Oct 2008
Posts: 7,263
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2008
Posts: 7,263 |
Some float the back end of the stock but on mine it has solid contact with the receiver and hanger the barrel is free floated. It shoots great so I won't touch a thing.
"When you disarm the people, you commence to offend them and show that you distrust them either through cowardice or lack of confidence, and both of these opinions generate hatred." Niccolo Machiavelli
|
|
|
|
Joined: Jan 2014
Posts: 4,964
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2014
Posts: 4,964 |
Some float the back end of the stock but on mine it has solid contact with the receiver and hanger the barrel is free floated. It shoots great so I won't touch a thing. Thats goid bevause it the barrel is not touching the forend then floating the back of the forend would not do a thing except make an ugly gap... The whole idea (or more correctly- theory) is that if the forend is bedded to the barrel, the barrel heat MAY cause enough expansion to move the forend back enough to bind the forend bewteen the action and the barrel so that harmonics /accuracy is affected. The rear of the forend would have to be pretty tightly bedded to the receiver to cause that and the Brownings just have a flat butt joint between the two. The Ruger number 1 & 3 rifles have that angled forend screw which pulls it up and back toward the action. That is what can cause the fit issue if the barrel is not floated.
Last edited by jk16; 11/19/17.
|
|
|
|
Joined: Oct 2008
Posts: 7,263
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2008
Posts: 7,263 |
If the fore end either wobbles or makes contact then relieving the barrel channel and glass bedding to the hanger only is the way to go in my opinion. Like jk16 said contact with the action is not critical on the low wall.
"When you disarm the people, you commence to offend them and show that you distrust them either through cowardice or lack of confidence, and both of these opinions generate hatred." Niccolo Machiavelli
|
|
|
|
Joined: Jan 2014
Posts: 4,964
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2014
Posts: 4,964 |
H Some float the back end of the stock but on mine it has solid contact with the receiver and hanger the barrel is free floated. It shoots great so I won't touch a thing. Thats good bevause it the barrel is not touching the forend then floating the back of the forend would not do a thing except make an ugly gap... The whole idea (or more correctly- theory) is that if the forend is bedded to the barrel, the barrel heat MAY cause enough expansion to move the forend back enough to bind the forend bewteen the action and the barrel so that harmonics /accuracy is affected. The rear of the forend would have to be pretty tightly bedded to the receiver to cause that and the Brownings just have a flat butt joint between the two. The Ruger number 1 & 3 rifles have that angled forend screw which pulls it up and back toward the action. That is what can cause the fit issue if the barrel is not floated.
|
|
|
|
Joined: Jun 2005
Posts: 1,468
Campfire Regular
|
Campfire Regular
Joined: Jun 2005
Posts: 1,468 |
I remember it clover leafing 3 shots at 100 yards. Now with the same loads it puts 2 real close but the 3rd shot always seems to wander an inch or so....
So ... lemme get this straight. You have a single shot. You are wigging out about the third shot moving an inch in POI. Sounding like a solution in search of a problem, doesn't it? Enjoy your very cool rifle! GE
|
|
|
|
476 members (1eyedmule, 10gaugemag, 17CalFan, 12344mag, 10gaugeman, 160user, 54 invisible),
2,687
guests, and
1,327
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,191,491
Posts18,471,985
Members73,936
|
Most Online11,491 Jul 7th, 2023
|
|
|
|