|
|
Joined: Dec 2015
Posts: 292
Campfire Member
|
OP
Campfire Member
Joined: Dec 2015
Posts: 292 |
I have some loads that were loaded some time ago, and I don't remember what exactly they are. I'd like to take them apart. Is there any good way to get the compressed BP out besides at the range? I plan on pulling the lead and recasting that.
Thanks, KB
A gun in hand is worth two cops on the phone. MOLON LABE LET'S GO BRANDON!!
|
|
|
|
Joined: Jan 2001
Posts: 29,851
Campfire Ranger
|
Campfire Ranger
Joined: Jan 2001
Posts: 29,851 |
My experience is that compressed loads have to be scraped out.
1Minute
|
|
|
|
Joined: Nov 2003
Posts: 4,275
Campfire Tracker
|
Campfire Tracker
Joined: Nov 2003
Posts: 4,275 |
pull the bullet and scrape the powder out.
the most expensive bullet there is isn't worth a plug nickel if it don't go where its supposed to. www.historicshooting.com
|
|
|
|
Joined: Oct 2006
Posts: 4,236
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2006
Posts: 4,236 |
Yup, pull the bullet and wad, scrape the powder out.
Difficulty of scraping gets higher the more compressed the powder is. I don't crimp my loads so the bullet removal is EZPZ. Getting the wad out can be challenging but the judicious use of a small 'eyeglass' screwdriver usually works well. Scrape and dump powder, go slowly and use a brass pick or small brass screwdriver. Neck resize case to remove crimp and true the mouth. Unless something doesn't go well, I am able to reuse all the components and replace those I need to with new. YMMV
Someday I hope to be the person my dogs think I am . . . The only true cost of having a dog is its death. Someone once said "a nation of sheep will beget a government of wolves." Shiloh Sharps . . . there is no substitute. NRA Endowment Member
|
|
|
|
Joined: Jan 2017
Posts: 8,895
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2017
Posts: 8,895 |
Why don't you just shoot them?
" Cheapest velocity in the world comes from a long barrel and I sure do like them. MB "
|
|
|
|
Joined: Oct 2011
Posts: 383
Campfire Member
|
Campfire Member
Joined: Oct 2011
Posts: 383 |
For what the cost of powder and primers just shoot them empty and enjoy the time being the rifle.
Digging the powder out and reusing it, it might only good for priming the flint lock.
I have .45-70 loads that my Daughter shoots in the rifle I set back for her use that have been loaded for many many years that didn't get shot up and she still out shoots me when we get together spending time at the range.
|
|
|
|
Joined: Feb 2004
Posts: 19,191
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2004
Posts: 19,191 |
What caliber ? Check with Midway or Brownell's for a collet for your caliber and pull the bullets. It's actually pretty easy.
kwg
For liberals and anarchists, power and control is opium, selling envy is the fastest and easiest way to get it. TRR. American conservative. Never trust a white liberal. Malcom X Current NRA member.
|
|
|
|
Joined: Nov 2003
Posts: 4,275
Campfire Tracker
|
Campfire Tracker
Joined: Nov 2003
Posts: 4,275 |
Hammer type bullet puller works ok. You can also just run the rounds up the press until you can grab the bullet with a pair of pliers and lower the ram. Cast bullets won't be good for much no matter how you pull them so they go back in the pot for a reman.
the most expensive bullet there is isn't worth a plug nickel if it don't go where its supposed to. www.historicshooting.com
|
|
|
|
Joined: Jun 2020
Posts: 787
Campfire Regular
|
Campfire Regular
Joined: Jun 2020
Posts: 787 |
I have had good luck with the Hammer type as Ranch 13 suggested. I put a wad of cotton in the bottom of mine to stop the bullet and have had very good luck with little or no bullet deformation.
Last edited by elkmen1; 02/16/23.
|
|
|
|
Joined: Jan 2017
Posts: 8,895
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2017
Posts: 8,895 |
Pull them with the trigger if they don't go off then a puller...jeez
" Cheapest velocity in the world comes from a long barrel and I sure do like them. MB "
|
|
|
|
594 members (17CalFan, 007FJ, 160user, 12344mag, 1337Fungi, 10gaugemag, 71 invisible),
2,459
guests, and
1,223
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,191,777
Posts18,477,000
Members73,942
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|