|
Joined: Aug 2021
Posts: 121
Campfire Member
|
OP
Campfire Member
Joined: Aug 2021
Posts: 121 |
I have a kimber 82 in 22 hornet. Former owner had a stuck case. Proceeded to gouge it out with tool steel picks. The chamber has large scratches and deep cuts. It’s in pretty good shape and worth saving if the chamber can be fixed. I’m at a loss so looking for advice.
|
|
|
|
Joined: Jun 2006
Posts: 3,221
Campfire Tracker
|
Campfire Tracker
Joined: Jun 2006
Posts: 3,221 |
Would rechambering to 22 K-Hornet clean up the scratches?
|
|
|
|
Joined: Jan 2001
Posts: 7,988 Likes: 3
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2001
Posts: 7,988 Likes: 3 |
Take it to a gunsmith and see if he recommends polishing the chamber and whether he can do it without damaging the chamber. Usually, just a good polish with very fine sandpaper like 1000/2000 grit wet/dry paper and a polish will take care of scratches unless they are really deep.
Never underestimate your ability to overestimate your ability.
|
|
|
|
Joined: May 2011
Posts: 56,326 Likes: 9
Campfire Kahuna
|
Campfire Kahuna
Joined: May 2011
Posts: 56,326 Likes: 9 |
If the case separated and the back came out, odds are the damaged area is far enough above the rim that a rechamber to K Hornet will remove it, depending on depth of gouges of course. If he gouged it up near the rim maybe not. It can always be set back and rechambered. Or rechambered to something else, provided it would work in the magazine. 256 Win Mag maybe?
_______________________________________________________ An 8 dollar driveway boy living in a T-111 shack
LOL
|
|
|
|
Joined: Nov 2006
Posts: 10,809
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2006
Posts: 10,809 |
Without looking at it for a better idea, I can tell you what I'd try if it were mine: I'd drill and tap a (preferably fired) Hornet case through the primer pocket as large as possible, maybe 10-32, and screw it down on the end of a 2" long or so 10-32 SHCS (machine screw) on which I'd already run a 10-32 nut down a half inch or so and had put an appropriate washer over the nut. (The washer being between the nut and the base of the Hornet case.)
When I had the nut and washer up tight against the Hornet case, so it wouldn't turn on the machine screw (using the nut as a lock nut), I'd charge the hornet case with some lapping compound of about 600 grit. I'd run my case/lap thus charged, into the chamber and, using a t-handle hex wrench in the socket cap of the machine screw, lap the chamber until it started feeling smooth, just enough to take down whatever burrs had been raised. I wouldn't try to remove any deep scratches, just clean up the burrs.
Then I'd flush out the chamber and barrel thoroughly and try it. I'd want to have a sturdy, one piece cleaning rod or 3/16 length of steel or brass rod on hand in case it stuck another case. If it works okay, rock on... or try a little more polishing. Play it by ear. That's what I think I'd try.
Mathew 22: 37-39
|
|
|
|
Joined: May 2009
Posts: 1,359
Campfire Regular
|
Campfire Regular
Joined: May 2009
Posts: 1,359 |
Without looking at it for a better idea, I can tell you what I'd try if it were mine: I'd drill and tap a (preferably fired) Hornet case through the primer pocket as large as possible, maybe 10-32, and screw it down on the end of a 2" long or so 10-32 SHCS (machine screw) on which I'd already run a 10-32 nut down a half inch or so and had put an appropriate washer over the nut. (The washer being between the nut and the base of the Hornet case.)
When I had the nut and washer up tight against the Hornet case, so it wouldn't turn on the machine screw (using the nut as a lock nut), I'd charge the hornet case with some lapping compound of about 600 grit. I'd run my case/lap thus charged, into the chamber and, using a t-handle hex wrench in the socket cap of the machine screw, lap the chamber until it started feeling smooth, just enough to take down whatever burrs had been raised. I wouldn't try to remove any deep scratches, just clean up the burrs.
Then I'd flush out the chamber and barrel thoroughly and try it. I'd want to have a sturdy, one piece cleaning rod or 3/16 length of steel or brass rod on hand in case it stuck another case. If it works okay, rock on... or try a little more polishing. Play it by ear. That's what I think I'd try. I would do the same. If the case still sticks, rechamber to K.
|
|
|
|
Joined: Aug 2021
Posts: 121
Campfire Member
|
OP
Campfire Member
Joined: Aug 2021
Posts: 121 |
Ended up moving the gun. Apparently they are far more valuable than anticipated. Will be rechambered for a 218 bee single shot from what I understand.
|
|
|
|
668 members (007FJ, 12344mag, 10gaugemag, 10Glocks, 160user, 10ring1, 78 invisible),
2,377
guests, and
1,259
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,718
Posts18,494,638
Members73,977
|
Most Online11,491 Jul 7th, 2023
|
|
|
|