|
|
Joined: Jan 2009
Posts: 1,859
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2009
Posts: 1,859 |
I’m loading some 230 grain cast lead bullets for my s&w 625. Brass is full length sized, and checked in a Hornady headspace/case length gauge. Sized brass plunks right into the gauge with no problem. Seat a bullet, check in the gauge and no go. Seat bullet a little deeper, and the cartridge goes in the gauge a little further. I have to seat them what seems to be pretty deep to get them to plunk into the gauge. I understand that seating depth with increase pressure, these things seem pretty short to me. Can anyone explain to me what’s going on here?
|
|
|
|
Joined: Nov 2008
Posts: 8,662
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2008
Posts: 8,662 |
Plunk the rounds to the revolver and say bye bye to the gauge. IMO
Last edited by Swifty52; 03/05/24.
Swifty
|
|
|
|
Joined: Dec 2011
Posts: 959
Campfire Regular
|
Campfire Regular
Joined: Dec 2011
Posts: 959 |
Get a Lee Carbide crimp die. I had the same headache with some ammo. The Lee Carbide Crimp dies fixed the problem.
Nobody's right if everybody's wrong. Getting into reloading to save money is like getting married for free sex.
|
|
|
|
Joined: Jul 2004
Posts: 6,668
Campfire Tracker
|
Campfire Tracker
Joined: Jul 2004
Posts: 6,668 |
Plunk the rounds to the revolver and say bye bye to the gauge. IMO ^This^ They are gonna be fired in the revolver, not that that gauge.
'Four legs good, two legs baaaad." ---------------------------------------------- "Jimmy, some of it's magic, Some of it's tragic, But I had a good life all the way." (Jimmy Buffett)
SotG
|
|
|
|
Joined: Jan 2009
Posts: 1,859
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2009
Posts: 1,859 |
Did that, the ones that are seated long only go half way into the cylinder.
|
|
|
|
Joined: Nov 2008
Posts: 8,662
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2008
Posts: 8,662 |
1.275 max length with 230 ball. Your revolver is telling you they are too damn long.
Swifty
|
|
|
|
Joined: Feb 2024
Posts: 175
Campfire Member
|
Campfire Member
Joined: Feb 2024
Posts: 175 |
If your Cast Bullets are a bit oversize they will in some cases expand the case making them difficult to chamber. I size to .452 /.453 diameter and Load to recommended OAL. At .454 I had the same problem with a 625 Revolver, and a tight chambered Colt 1911 Match gun.
You know you might be facing your doom if all you get is a click when you are expecting a BOOM !
|
|
|
|
Joined: Jan 2009
Posts: 1,859
Campfire Regular
|
OP
Campfire Regular
Joined: Jan 2009
Posts: 1,859 |
That was the problem right there. These were purchased from a commercial caster. And I checked them this morning and they are .454. Ran them through a Lee sizing die and now they are good to go.
|
|
|
|
Joined: May 2018
Posts: 1,509
Campfire Regular
|
Campfire Regular
Joined: May 2018
Posts: 1,509 |
Years ago I switched to .45 auto rim cases for my 45acp revolvers. For me it made things a lot easier.
Old guy, old guns.
|
|
|
|
592 members (12344mag, 10gaugemag, 160user, 22250rem, 10ring1, 007FJ, 64 invisible),
2,440
guests, and
1,313
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,203
Posts18,485,289
Members73,966
|
Most Online11,491 Jul 7th, 2023
|
|
|
|
|