Home Forums Hunting & Shooting Custom Rifles & Wildcats RIFLE BLUEPRINTS ONLY!

Sounds like it will be an awesome rifle when done. You'll have most of the bases covered with that set. Wish I would have bought two when I got the one I have. I've considered wood also, but will most likely go with a McM. I have a couple of other rifles that need some attention first so I have pleanty of time to change my mind. Tom

There are a lot of really great looking rifles on here. I figured I would put a few of mine up.

First is a 458 Lott built by Stan Jackson here in Anchorage. Built on a winchester 70 classic action originally a 300 Win mag. 24" douglas barrel with muzzle break and cap so I can take the muzzle break off to hunt with. Accurate innovations stock with full aluminum bedding block. Gold blade sourdough front sight and brockman pop up peep bases with QD talley rings and Leupold 1.5-5 illuminated VXIII, german #4 dot reticle.

I haven't worked up much in the line of heavy loads thru it but have around 250 rounds of 350gr Speer mag tip @ 2760fps. Mild to shoot and very accurate. I have shot several 5 shot groups at 100 yards 1" or less. The pop up peep and sourdough blade dead on at 25 yards and hits a couple inches high at 100 yards. That sourdough blade is very easy to place shots with.

Winchester M70 classic
24" douglas barrel
Leupold VXIII 1.5-5 Illuminated german #4
10.5 lbs with scope.

The second one is a lightweight 375 H&H done on a winchester 70 classic. In its factory configuration with a hogue overmolded stock it was a heavy SOB. After just one trip moose hunting I knew something had to be done about it. I sent it off to Extreme rifle works, out of Palmer alaska. I told him to make it as light as possible. They turned down the factory barrel contour, trimmed all possible metal from the action and the bolt and then bedded it into an ultra light kevlar stock. Cut the barrel back to 20" and installed a tritium bead front and brockman pop up peep rear. I originall had the 1.5-5 leupold VxIII that is now on my lott but have since replaced it with a ziess 3-9x40 conquest. It is one brutal SOB off the bench but is a joy to carry and is my go to gun whenever travel is involved. I'm going to work up a lot for it with the 270gr TSX for this years hunting season.

Winchester 70 classic
weighs right at 6 lb 4 oz without the scope and weight with scope is a little over 7 lbs.

My Go To..... .338 Winchester Magnum

Sako AV magnum action
#3 Douglas Chrome Moly barrel finished at 25"
McMillan Fiberclass sako hunter
All metal finished in ROBAR NP3
Sako Conetrol Mounts
Leupold FX-III 6x42 matte

7 pounds 12 ounces

The wifes .243 Winchester

Remington 700 SA
Bolt fluted by Karl Kampfeld
Factory Mt. Barrel 22"
Mcmillan compact hunter BDL 1inch decel pad
Factory aluminum bottom metal
Factory tuned trigger 3 pounds
Talley lightweight lows
Leupld VXII 2-7 x33
Graphite Black Cerakote done by Charley Santoni (CAS)

6lbs 9oz

[img][IMG]http://img.photobucket.com/albums/v336/Georgedevries/P9260005-1.jpg[/img][/img]

MRC M1999 barrelled-action in .458 Lott by Roger Ferrell.
22" barrel crowned
NECG banded front ramp & hood with fiberoptic bead - soldered and screwed (rear also)
Talley bannded swivel base
NECG adjustable rear sight
Pillar bedded McMillan stock
Action polished and smoothed, trued and blueprinted
Trigger & sear Honed. Adjusted to crisp 3.5 lbs
Williams triggerguard
Black -T finish
Leupold 2.5-20 scope with Talley rings & bases
Action drilled & tapped for 8-40s. Bases soldered and screwed to receiver.


Edited to add this one too:
[img][IMG]http://img.photobucket.com/albums/v336/Georgedevries/P9260006.jpg[/img][/img]

Gdv

Husqvarna 1900 action
honed action and trigger worked by Griffin&Howe
Hart #4 24" 1-12 twist
McMillan Remington Mountain Rifle stock (bedded by them)
Black-T by Birdsong
2pc. Buehler mounts (Black-T)
2.5-10x40 B&L Elite 4000

Satterlee Arms Titanium Mauser Action
7x57
MPI Kevlar Stock
HEYM octagon Barrel 23"
Integral bases & Talley Rings
Leupold LPS 2.5-10x45

7 pounds, 0 ounces as it sits.

Still needs coating.

Seet, Satterlee is finishing a Mex Mauser for me.

Those Satterlee actions are very nice.

For $6500 FOR THE ACTION ALONE, they better damned well be.....

Hey, WTF, Echols can get something like 12G's for a completely reworked Model 70. I'll bet the total on that other one is much less. I sure they work like a dream, but seriously, 12G's????


Roy

I think not....

Kampfeld Custom-- Karl did all the work to this gun, except the camo dip
Rem 700 SA TI,Factory recoil lug
.358 Win, 1 in 12", 1" shank, Lilja #3 SS, 20" barrel measured from gas port
McMillan EDGE Rem Mod 7, 1 " Decel. (From Rick)
Bedded/Floated stock
Callahan Bolt Handle, Bolt Knob, and Bolt Shroud. (Karl also modified this handle to accomodate my scope.)
Tubb pin/spring
Factory BDL bottom metal
Factory Trigger worked on, 40 ozs.
Trued bolt
Kahles AH 2-7x36 4a Reticle Scope w/Butler Creeks
Conetrol Custum Low Rings and Bases Fluted by Karl (weigh 4 oz total for pair)
Barreled Action and Scope bases Cerakoted Titanium
Scope Rings Cerakoted Graphite Black
Stock Camo Dipped at http://www.camoent.com
5.5lbs bare
6 lbs. 13 oz. as you see it unloaded.

Rem 7 SS 7SAUM
Mcswirly Rem Classic, 50/50 black/white
6x36 & talleys from Midway
just waiting on an ADL trigger guard and gre-tan shroud/pin to delete the gaylock.

7.25 with 3 in the belly, balance is halfway between the trigger and the front action screw.

Rem 700 Mtn Rifle

Rem 700 S/A*, CM, KG GunKote Matte Black, alloy shroud
7-08AI, 11 twist #2.5 SS Pac Nor at 23", rebarreled by PacNor (Ernie Boardman)
RifleBasix Trigger
McM Mtn Rifle stock, ADL, 50% Olive, 25% med tan, 25% black
Pillar bedded in Ceibe Geige epoxy & Marine Tex, .8" decelerator
Leupold VX-III 2.5-8, Leupold DDs

MtnHtr

Specs:

Winchester classic action
McMillan Edge Super grade stock, 13.5" LOP, painted olive, 1" pad
Pac-nor 26" #3 fluted barrel. 1 in 10 twist. 3-groove.
Factory trigger adjusted to 3 lbs.
Williams one-piece bottom metal.
Talley low rings & bases
Leupold VX-III 3.5-10x40 with B/C reticle.

Rifle is chambered for 300 RUM.

As pictured, comes in under 8 lbs.

Mtnhunter,

what is the wieght on that rig? Curious as I'm building an almost exact copy with exception of edge stock and 22" tube.

recently restocked this Cooper .20 Vartarg after having Kevin Weaver rough out the blank of Bastonge I sent him.

Cooper M38- .20 VT
Talley LW Rings
Leupold: 12X
9 lbs 8 oz as it sits







ML

Just under 8lbs IIRC, it was for a friend in OR. I built another one on an Edge - it's posted earlier in this thread under "Blacktail Slayer Blueprint".

MtnHtr