|
Joined: Mar 2010
Posts: 47
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2010
Posts: 47 |
Ive got a vanilla Savage 111 with a 9" twist broughton pipe (25") Just Started fireforming some 25-06 WW brass with (87gr. speer over 49gr. IMR-4320) Seems to be forming ok, maybe a a bit of stretch in the case head so Ill have to work on this. Ill also be forming some 270 brass instead of 25-06 as it seems I can make a better crush fit to set headspace on inital fireform (I wonder if my chamber is a bit long). Im up against the lands at about 3.113 with seems a bit short but standard if I look up some numbers from Sierra...might eventually get the throat opened up to play with longer bullets bullets like the Matrix 125gr. and Barnes 115.
Either way Im hoping to working up a load for 100gr. TSX and R22 soon and be ready for Deer season.
Everything Ive read about this chambering seems to point to R22 for speed an 100's, looking forward to your comments.
Last edited by northcoast; 08/17/12.
|
|
|
|
Joined: Feb 2002
Posts: 1,818
Campfire Regular
|
Campfire Regular
Joined: Feb 2002
Posts: 1,818 |
My first and only experience to date with an AI is a 6.5-06. I bought it online from snipershide a couple years ago. It came with 50 fireformed round of Win. 25-06 brass. As I started to work up loads, I started with 4831. I also fireformed some new R-P brass with some old Accurate 8700 and Speer 120s. The 4831 loads shot well but I noticed the pressure snuck up on me. I lost a couple primer pockets and and backed down. I also noticed the Win. brass had several head seperations within three loadings. I went to the R-P brass when I found they weighed about 6 grains more and I assumed they were a bit thicker. I also jambed the bullets into the lands to keep them from stretching when first fireformed. That seemed to end the separations and they are still going strong. As far as R22, I tried it upon reccomendations here. I found very little difference in accuracy and speed from 4831. My rifle has only a 10' twist, so I am limited to 120s and less. I was getting about 3100 and change from both powders. It shot great groups with both the 100 and 120BT, but the pressure was up there and I thought it should do a little better as far as speed. 7828 was about the same, but then I tried Hunter. I was able to reach 3200 with both 120bt and the 123 A-max without any trouble, and they shoot great. I did find, however, that I was getting hangfires with standard primers and a switch to mag seems to have solved the problem. Just the other day I was shooting at steel at 600 and 750. With the A-max, I was at 10moa at 600 and about 12 moa at 750. The gongs were about 8". At 600 I had 3 hits with a 15-20 mph headwind. (about 11 o'clock). I didn't get a hit at 750 because I ran out of ammo and didn't have time to get a handle on the gusting wind, but the three shots I did take were right there. Overall , I am very happy with the Hunter and don't think I will use anything else in the future. It was a pleasant surprise. Let us know how it goes. Jeff.
I think, therefore I am, conservative.
|
|
|
|
Joined: Mar 2010
Posts: 47
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2010
Posts: 47 |
thanks for you comments, im also going to try fireforming few without bullets for the hell of it. The fastest powder I have is 4759 Im thinking about 18gr. with TP will do it.
Will also make sure to jam bullet next time I fireform with a bullet.
|
|
|
|
Joined: Nov 2007
Posts: 8,460 Likes: 2
Campfire Outfitter
|
Campfire Outfitter
Joined: Nov 2007
Posts: 8,460 Likes: 2 |
My gunsmith(s) set up my AI chambers so std factory brass crush-fits in the chamber, thus no case growth at the web on fire-forming. As you note, alternatively, a false shoulder such as is created by necking down '06 or .270 brass just enough to fit will help. Watch out for case neck thickness / chamber neck clearance issues if you're necking down from a larger size. Stuffing a bullet into the rifling works in a pinch. The blunter the bullet, the more likely you'll be to be able to get good contact. In .25 caliber, heck into the 117 grain Hornady roundnose for this use. My current AI is a 6mm Rem AI. The chamber is set up as in my first example above. The gol dang case forming load is more accurate than any of my full throttle AI loads. The plus side is, there are no wasted shots at the range, I just use 'em to pound ground squirrels like any other load. So far as the .25-'06 AI ... I don't see a lot of use for the cartridge since 700 actions with a magnum bolt face are readily available, .257 Weatherby is faster yet, and its easy enough to make .257 weatherby brass from .264 or 7mm mag, however, the idea of having an AI reamer dropped into a Kimber 84L .25-'06 sorta tickles my insanity. Lotta reach in a light rifle iff the accuracy is there. Tom
Anyone who thinks there's two sides to everything hasn't met a M�bius strip.
Here be dragons ...
|
|
|
|
Joined: Jan 2009
Posts: 8,900 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2009
Posts: 8,900 Likes: 1 |
100 grain bullets with around 60-61 grains of RE22 worked well in the two 25-06 Ackleys I've been around.
|
|
|
|
Joined: Mar 2010
Posts: 47
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2010
Posts: 47 |
Prairie Goat, do you recall the velocity with those loads ? around 3500fps Im guessing ?
|
|
|
|
Joined: Jan 2009
Posts: 8,900 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2009
Posts: 8,900 Likes: 1 |
Yep, right around 3500 give or take a bit. One barel was 26", the other 23".
|
|
|
|
Joined: Mar 2010
Posts: 47
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2010
Posts: 47 |
Also thanks Tom,
Ill have see how the 270 brass angle works out, dont' have any 117RN's but the 125's I have do have a lot of bearing surface so they would jam nicely.
|
|
|
|
Joined: Feb 2002
Posts: 1,818
Campfire Regular
|
Campfire Regular
Joined: Feb 2002
Posts: 1,818 |
In my 6.5 I was getting 3500 with the 100bt, shot scary good. You guys have me contemplating having my soon-to-be 25-06 AI'd
I think, therefore I am, conservative.
|
|
|
|
Joined: Nov 2007
Posts: 29,653 Likes: 5
Campfire Ranger
|
Campfire Ranger
Joined: Nov 2007
Posts: 29,653 Likes: 5 |
Yep, right around 3500 give or take a bit. One barel was 26", the other 23". Seriously? That is what I'm getting in my Weatherby Mag from 100 gr ETips & 70 gr RL22...
|
|
|
|
Joined: Mar 2008
Posts: 37
Campfire Greenhorn
|
Campfire Greenhorn
Joined: Mar 2008
Posts: 37 |
Mine chrono'ed 3450 with R22 and 100 TSX, in a 25" custom barrel.
|
|
|
|
Joined: Dec 2001
Posts: 435
Campfire Member
|
Campfire Member
Joined: Dec 2001
Posts: 435 |
Are you getting a crush fit because the 270 brass is longer and you are hitting the end of the neck in the chamber? Or are you cutting the 270 to length first?
Just my 2 cents.
|
|
|
|
Joined: Sep 2009
Posts: 46,261 Likes: 2
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Sep 2009
Posts: 46,261 Likes: 2 |
Yep, right around 3500 give or take a bit. One barel was 26", the other 23". Yessir, I run the 100 gr TTSX's out at 3552 fps in a 28" barrel with 61.0 grs. RL-22 and a CCI-250 primer in WW brass. Shoots three at .331 in calm winds. Gunner
Trump Won!
|
|
|
|
Joined: Feb 2005
Posts: 9,472
Campfire Outfitter
|
Campfire Outfitter
Joined: Feb 2005
Posts: 9,472 |
In my 25-06 AI I have had great luck with H4350 and the 100gr tsx. I have also had god luck with heavier bullets using Magnum and Retumbo.
|
|
|
|
Joined: Feb 2002
Posts: 7,202 Likes: 1
Campfire Tracker
|
Campfire Tracker
Joined: Feb 2002
Posts: 7,202 Likes: 1 |
Don't worry about lengthening your throat unless you are using R#25 with a custom bullet weight over 120g.
|
|
|
|
Joined: Apr 2009
Posts: 1,972
Campfire Regular
|
Campfire Regular
Joined: Apr 2009
Posts: 1,972 |
What speeds are you able to get with a 115 or 120gr. bullet?
|
|
|
|
Joined: Mar 2010
Posts: 47
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2010
Posts: 47 |
about the fit, Ive resized it partly (part of neck) and trimmed to 2.484
All those 25-06 had been resized prior to acquiring the rifle when I had 6.5-06 so from now any brass I resize I only resized to the point where I can get a crush fit. The ones I did already will probably not last as long but If the 270's work better Ill stick to that.
|
|
|
|
Joined: Mar 2010
Posts: 47
Campfire Greenhorn
|
OP
Campfire Greenhorn
Joined: Mar 2010
Posts: 47 |
About the throat, ive got some 125's and there are more readily available, Ill see what I can do with the throat I have now...I think throating would give me some powder space/ alleviate pressure. Ill see when i start playing with them later on.
|
|
|
|
Joined: Jan 2009
Posts: 3,001
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2009
Posts: 3,001 |
What speeds are you able to get with a 115 or 120gr. bullet? Not Keith, but I'm well into the 3200's with 117/120's But found accuracy with 100gr NPT's... Deer Hate 'em
"I'd rather have an Army of Asses led by a Lion, than an Army of Lions led by an Ass." (George Washington)
|
|
|
|
Joined: Aug 2012
Posts: 191
Campfire Member
|
Campfire Member
Joined: Aug 2012
Posts: 191 |
Had a couple over the years fun to work with. RE 22 has always been good ....3500 is pushing it a bit in a 26 tube...pressure signs like a sticky bolt lift kind of evade youin a AI or gibbs cartridge.....but the primer wont lie..... try Sierra 117 SPBT.......and you got a helluva killer there... would not do a AI anymore.....just use a .257 Roy......but thats just me
|
|
|
|
242 members (1beaver_shooter, 1minute, 1_deuce, 16gage, 204guy, 17CalFan, 37 invisible),
1,865
guests, and
1,043
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,861
Posts18,497,178
Members73,979
|
Most Online11,491 Jul 7th, 2023
|
|
|
|