|
Joined: Feb 2011
Posts: 733
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2011
Posts: 733 |
I just completed my 257 AI and this is my first experience with fire forming brass. What powders are acceptable for the COW method? I don't load for pistols and the fastest burning powder I have is IMR 4227. Will this work or do I need to pick up some Unique or similar burn rate? Thanks in advance for any advice.
|
|
|
|
Joined: Aug 2002
Posts: 19,138 Likes: 6
Campfire Ranger
|
Campfire Ranger
Joined: Aug 2002
Posts: 19,138 Likes: 6 |
I can't answer your question but I will say after doing that one time, I doubt that I will go that route again. I would just load some ammo to 257, near max loads, and fire form that way. miles
Look out for number 1, don't step in number 2.
|
|
|
|
Joined: Aug 2008
Posts: 1,394
Campfire Regular
|
Campfire Regular
Joined: Aug 2008
Posts: 1,394 |
Don't screw with COW. A waste of time and components. Just load with bullets and go shoot. Choose a powder and bullet. Start at the top of std. 257 loads and go from there til you find best accuracy, that'll be your fireform load. It'll be as accurate as formed brass and very nearly the same velocity. My fireform load used W760 and an 85/87gr bullet doing high 3700's with 28" barrel.
|
|
|
|
Joined: Feb 2003
Posts: 18,854
Campfire Ranger
|
Campfire Ranger
Joined: Feb 2003
Posts: 18,854 |
I used Bullseye. PM Mule Deer and ask him. He seems to have some experience with it.
Sent from my Dingleberry Handheld Wireless
|
|
|
|
Joined: Feb 2009
Posts: 4,534
Campfire Tracker
|
Campfire Tracker
Joined: Feb 2009
Posts: 4,534 |
Don't screw with COW. A waste of time and components. Just load with bullets and go shoot. Choose a powder and bullet. Start at the top of std. 257 loads and go from there til you find best accuracy, that'll be your fireform load. It'll be as accurate as formed brass and very nearly the same velocity. My fireform load used W760 and an 85/87gr bullet doing high 3700's with 28" barrel. + 1!!! BULLETS!
Last edited by joshf303; 08/11/14.
|
|
|
|
Joined: Dec 2004
Posts: 10,361 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Dec 2004
Posts: 10,361 Likes: 1 |
I have used Bullseye and a wax plug for fireforming. Do whatever you want.
|
|
|
|
Joined: Mar 2003
Posts: 5,865 Likes: 13
Campfire Tracker
|
Campfire Tracker
Joined: Mar 2003
Posts: 5,865 Likes: 13 |
I used Bullseye when I formed my first 400 Whelen cases. It was about the only way I had to make cases at the time as I didn't have reloading dies or an expander dies set for it. I used about 16 grains of Bullseye and topped it off with COW and jammed a crayon in the case mouth. It worked well.
However, for the 257 AI I wouldn't bother. Just load up your standard cases and fire away. Unless you just don't want to burn up that many bullets. In that case I think the 4227 would work. I'd start around 12 grains and go up till you come out with well formed cases.
Chronographs, bore scopes and pattern boards have broke a lot of hearts.
|
|
|
|
Joined: Jul 2008
Posts: 918
Campfire Regular
|
Campfire Regular
Joined: Jul 2008
Posts: 918 |
I'm with these guys, COW will form out about right, but the shoulder will still not be as sharp as it will be with a good stiff load! I got a box of plus P rounds and they still weren't hot enough to get it done completely!
Semper Fi USMC/0331
|
|
|
|
Joined: Feb 2002
Posts: 7,207 Likes: 1
Campfire Tracker
|
Campfire Tracker
Joined: Feb 2002
Posts: 7,207 Likes: 1 |
Work up an accurate load with bullets, it will probably be an over max load for the regular cartridge, hunt while fire forming. Accuracy and speed will be spectacular. I am assuming that you are not shooting over 300+ yards.
I don't think that Bullseye can be purchased anymore, they may have closed the plant down in Va. that made Unique, Red Dot, Green Dot, American Select, and Power Pistol.
I too have used Bullseye and wax plug..works well...
Last edited by keith; 08/12/14.
|
|
|
|
Joined: Jun 2006
Posts: 46,386 Likes: 19
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2006
Posts: 46,386 Likes: 19 |
I've used Unique and Bullseye in my 6.5-06 AI, but I gave up on it and just load cheap bullets and a max load of fast powder for the parent cartridge and shoot. My chamber is properly head spaced for the crush fit (I watched the gunsmith gauge it) but for some reason I got a few case separations with COW, go figure.
"Hunt while you're fireforming" would work with something like PDs, and would be a lot of fun. My FF loads were very accurate.
A wise man is frequently humbled.
|
|
|
|
Joined: Jan 2008
Posts: 14,215 Likes: 29
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2008
Posts: 14,215 Likes: 29 |
Not very glamorous, but you could just load up some according to a 257 Roberts recipe out of a manual and just go kill something. Fireformed brass would then be a bonus.LOL
Best,
GWB
A Kill Artist. When I draw, I draw blood.
|
|
|
|
Joined: Feb 2011
Posts: 733
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2011
Posts: 733 |
Sounds like the general concensus is to load and shoot. I dont really feel that "crush fit" and I dont have a gauge to check head space. However, it was done by a competent smith and a new barrel...I tend to over-think these things. Thanks for the advice, guys.
|
|
|
|
Joined: Jun 2004
Posts: 44,949 Likes: 25
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,949 Likes: 25 |
Can't feel the "crush" fit? I'd be inclined to load the first batch of bullets into the lands.
|
|
|
|
Joined: Feb 2011
Posts: 733
Campfire Regular
|
OP
Campfire Regular
Joined: Feb 2011
Posts: 733 |
Now you have me thinking again, Mathman. What type of charge do you recommend with the long seated bullet? Moderate or Max charge?
|
|
|
|
Joined: Jun 2006
Posts: 46,386 Likes: 19
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2006
Posts: 46,386 Likes: 19 |
You'd be OK with the upper end charge for the parent cartridge, but there's nothing wrong with backing off a grain or two. If you have a choice, use a heavy bullet and a powder toward the fast end for the cartridge.
A wise man is frequently humbled.
|
|
|
|
Joined: Jun 2004
Posts: 44,949 Likes: 25
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,949 Likes: 25 |
257 Roberts max charges are pretty tame in the overall scheme of things. This is similar to the 250 Savage.
I recently formed some 22-250 brass for my 250 Savage, regular, not AI. I seated some 90 grain Sierras so they'd be firm into the lands, and loaded them with a full load. The cases fireformed quite nicely. Bolt lift and extraction were smooth and easy, and primer signs indicated a load that was still quite mild.
You're blowing out the brass to a larger chamber, which would lower pressures even more.
If you want to be prudent, you could make up a series of one each at increasing charges to get a feel for it.
|
|
|
|
Joined: Jan 2001
Posts: 18,086 Likes: 1
Campfire Ranger
|
Campfire Ranger
Joined: Jan 2001
Posts: 18,086 Likes: 1 |
Not a waste of time when opening necks up to larger diameter!
Probably a waste of time if only AI'ing the brass!
Mike
God, Family, and Country. NRA Endowment Member
|
|
|
|
Joined: Apr 2010
Posts: 207
Campfire Member
|
Campfire Member
Joined: Apr 2010
Posts: 207 |
Its probably a toss up. A one lb. can of shotgun powder, vs. some cheap bullets. C of W can get pretty violent, but I use a 5 gal. bucket with a lid, lined with carpet scraps, in my garage.
Hornady's new hydraulic case forming die doesn't completely fill out the shoulders either. Dupont 700X is what I use. Start out at about 10 grains, and work up until its close enough to filling the shoulders out. Powder plus a primer, vs. Powder, primers, and bullets. Neil Jones specified that I should fire three full power loads, to get my cases formed out, completely.
The brass stabilizes after three firings. The C of W makes for decent first shot fire forming duties.
Last edited by INDYBUSTER; 08/12/14.
|
|
|
|
Joined: Sep 2006
Posts: 2,226
Campfire Regular
|
Campfire Regular
Joined: Sep 2006
Posts: 2,226 |
When I've done it, I've used Bullseye.
Murphy was a grunt.
|
|
|
|
Joined: Mar 2008
Posts: 3,518 Likes: 1
Campfire Tracker
|
Campfire Tracker
Joined: Mar 2008
Posts: 3,518 Likes: 1 |
Use Bullseye. You want the fastest powder available. Charge is 20% of what max charge weight is for your formed cartridge. Adjust until you get a formed case. Don't over do it. The case will not look as crisp as one fired with a full working load. Use PISTOL primers for forming step. Put those pistol primers away after forming!
“Perfection is achieved not when there is nothing more to add, but when there is nothing left to take away”. Antoine de Saint-Exupery. Posted by Brad.
|
|
|
|
519 members (219DW, 219 Wasp, 1OntarioJim, 1lessdog, 160user, 1936M71, 51 invisible),
10,751
guests, and
1,201
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,195,347
Posts18,546,589
Members74,060
|
Most Online21,066 May 26th, 2024
|
|
|
|