|
Joined: Jun 2012
Posts: 2,062
Campfire Regular
|
OP
Campfire Regular
Joined: Jun 2012
Posts: 2,062 |
I get 2812fps with Varget and 162gr Amax out of my 7mm-08AI. I had a batch of varget that would run faster but this lot won't without pressure. I'm also at 2.950 on oal running a AI mag. How long of a barrel you running with that velocity
"If you got it, you got it!" In memory of Pops, gone but never forgotten
|
|
|
|
Joined: Nov 2012
Posts: 151
Campfire Member
|
Campfire Member
Joined: Nov 2012
Posts: 151 |
|
|
|
|
Joined: Jan 2003
Posts: 4,069
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2003
Posts: 4,069 |
Want that AI to sing? Go 26" tube. 3100 very doable with 140/varget
Crossed Arrows Archery LLC Authorized Obsession Bows Dealer Custom Strings/Tuning www.crossedarrowsarcheryllc.comBlack Eagle Arrows Pro Staff, Montana Black Gold Shooting Staff, Dead Center Archery Products Shooting Staff
|
|
|
|
Joined: Jan 2009
Posts: 8,898
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2009
Posts: 8,898 |
Very doable at only 70k or more psi.
|
|
|
|
Joined: Dec 2004
Posts: 17,246
Campfire Ranger
|
Campfire Ranger
Joined: Dec 2004
Posts: 17,246 |
Dang, 140's at 3,100fps is 22-24" 7mm SAUM speeds.
Now with even more aplomb
|
|
|
|
Joined: Oct 2010
Posts: 3,379
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2010
Posts: 3,379 |
im having Jim Kobe build me a 7-08 AI with a 26" shilen sendero contour tube. Its being throated for 168bergers, what do you fellas think I could expect to see speed wise outta 168s.
I kill chit. "The Heathens nest"
|
|
|
|
Joined: Nov 2012
Posts: 151
Campfire Member
|
Campfire Member
Joined: Nov 2012
Posts: 151 |
im having Jim Kobe build me a 7-08 AI with a 26" shilen sendero contour tube. Its being throated for 168bergers, what do you fellas think I could expect to see speed wise outta 168s. 2712fps is where I was with 168gr Sierra MK's so I would imagine you will be in that area.
|
|
|
|
Joined: Oct 2010
Posts: 3,379
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2010
Posts: 3,379 |
nortex, would you be able to give me some specifics on the load? what powder/primer/charge weight? is that loaded to mag length or do you have it set out and measured off the Ogive? The dummy rounds i send are loaded so the 168 is right at the neck shoulder junction for maximum powder. COAL is right around 3.010
I kill chit. "The Heathens nest"
|
|
|
|
Joined: Mar 2002
Posts: 9,130
Campfire Outfitter
|
Campfire Outfitter
Joined: Mar 2002
Posts: 9,130 |
What action are you using? Is your magazine longer than 3.010?
|
|
|
|
Joined: Mar 2010
Posts: 7,866
Campfire Outfitter
|
Campfire Outfitter
Joined: Mar 2010
Posts: 7,866 |
For more reference I was getting 2700-2730 with Max loads of H414 from my stock 7-08 Kimber with 22" barrel.
The H414 gave better velocities and groups with the heavies than anything else I tried. The 160 AB did show more pressure than than 162 Amax (over .200" more bearing surface) but I got similar velocities.
It ain't what you don't know that makes you an idiot...it's what you know for certain, that just ain't so...
Most people don't want to believe the truth~they want the truth to be what they believe.
Stupidity has no average...
|
|
|
|
Joined: Jan 2010
Posts: 8,423
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2010
Posts: 8,423 |
Want that AI to sing? Go 26" tube. 3100 very doable with 140/varget I think that would be really world number with a 26" pipe I could get 3000 with the 140 and 21" pipe used reloader 19.
|
|
|
|
Joined: Jan 2010
Posts: 8,423
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2010
Posts: 8,423 |
Very doable at only 70k or more psi. Are your numbers based on using actual pressure equipment ( universal receiver, oehler. ) or just guessing with quick load and no real experience. Not trying to start a fight just want to know if you have real knowledge of the 7-08 AI or are speculating. I find that brass in the 243, 260, 7-08 and 308 will not hold primers after a load of 70 psi.
|
|
|
|
Joined: Jan 2010
Posts: 8,423
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2010
Posts: 8,423 |
I found RL 19 to post top velocities but went to varget due to temp sensitivity. With alliant coming out with the new powders to curve the temp problem it might be a 19 sub that gets a 168 to 2800.
|
|
|
|
Joined: Jan 2009
Posts: 8,898
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2009
Posts: 8,898 |
Varget is not Reloader 19, and will top out earlier with 140s. I have had a 7mm-08 Ackley, and did not find close to some of the magical velocities from this thread. Then again, I didn�t use the �load until I see pressure, then back down a grain� method. Besides, one doesn�t need to have used a particular cartridge to have a damned good idea what it will do for velocity. This isn�t the 1950s; plenty of pressure tested data is available to compare cartridges.
|
|
|
|
Joined: Jan 2009
Posts: 8,898
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2009
Posts: 8,898 |
Basically, a 7mm-08 AI will do what a 2� longer barreled 7mm-08 will do for velocity, at comparable pressures. If a person is seeing much more with the Ackley, it�s because they�re loading it hotter.
|
|
|
|
Joined: Oct 2010
Posts: 3,379
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2010
Posts: 3,379 |
What action are you using? Is your magazine longer than 3.010? its a rem 700 SA. im well aware that it wont load from the mag, im building it to shoot steel
I kill chit. "The Heathens nest"
|
|
|
|
Joined: Oct 2010
Posts: 3,379
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2010
Posts: 3,379 |
so you're saying that my rifle should do what a 7-08 with a 28" barrel should do.. im not sure ive ever seen load info for a 28" piped 7-08
I kill chit. "The Heathens nest"
|
|
|
|
Joined: Jan 2009
Posts: 8,898
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2009
Posts: 8,898 |
so you�re saying that my rifle should do what a 7-08 with a 28" barrel should do.. im not sure ive ever seen load info for a 28" piped 7-08 You will be also be able to gain some velocity due to your longer OAL. The question is, if single loading anyway why not go with a 284 and outpace both by a good margin?
|
|
|
|
Joined: Apr 2005
Posts: 30,939 Likes: 1
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Apr 2005
Posts: 30,939 Likes: 1 |
3.6" is the standard COAL got the 338 Lapua, I load mine to 3.860" and do not get any more velocity than others tat are loading to 3.6" COAL. Longer loaded length is no guaranty of extra velocity. I am running a 30" barrel on my Lapua.
I got banned on another web site for a debate that happened on this site. That's a first
|
|
|
|
Joined: Jan 2009
Posts: 8,898
Campfire Outfitter
|
Campfire Outfitter
Joined: Jan 2009
Posts: 8,898 |
3.6" is the standard COAL got the 338 Lapua, I load mine to 3.860" and do not get any more velocity than others tat are loading to 3.6" COAL. Longer loaded length is no guaranty of extra velocity. I am running a 30� barrel on my Lapua.
You are probably loading yours to sane pressures. The difference is case capacity is pretty minimal with the different OALs, anyway.
|
|
|
|
106 members (10Glocks, 35, arky65, afisher, AnthonyB, 01Foreman400, 11 invisible),
1,521
guests, and
797
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,503
Posts18,490,600
Members73,972
|
Most Online11,491 Jul 7th, 2023
|
|
|
|