|
Joined: Sep 2010
Posts: 4,004
Campfire Tracker
|
OP
Campfire Tracker
Joined: Sep 2010
Posts: 4,004 |
Just finished reading JB's article in the August Handloader on reloading dies. I have a 308 that is typically 1 1/2-2MOA and never seems to do any better. Haven't messed with it in a while but decided to start looking at my loads since the rifle has been tweaked every way I can think of. Put a few loaded rounds on the RCBS Casemaster and they were running out .006-.008 Hmmm... Checked a few fired cases and they ran out .001-.002. Took the stem out of my RCBS neck sizer and sized a few cases and they ran out .006-.008 Huh??? Switched shell holders and tried a different press all with the same results. Can't believe a neck sizer can induce that much run out. Ran a few through a Lyman collet die and they were .001-.002. Guess this one is going back to RCBS and probably ask them to replace it with a full length die since the Lyman is now my go to neck die.
I am continually astounded at how quickly people make up their minds on little evidence or none at all. Jack O'Connor
|
|
|
|
Joined: Sep 2015
Posts: 315
Campfire Member
|
Campfire Member
Joined: Sep 2015
Posts: 315 |
Curious to see how this ends up. If the loaded rounds come out straight and if so, how the rifle shoots with the "new" straight ammo.
Keep us posted.
|
|
|
|
Joined: Feb 2007
Posts: 7,439
Campfire Tracker
|
Campfire Tracker
Joined: Feb 2007
Posts: 7,439 |
Same thing happened to me. Just change the name to Redding. Lee collet die changed things for the better in a hurry.
You only live once, but...if you do it right, once is enough.
|
|
|
|
Joined: Jun 2005
Posts: 2,226 Likes: 2
Campfire Regular
|
Campfire Regular
Joined: Jun 2005
Posts: 2,226 Likes: 2 |
I went through this issue with my .308 Palma rifle recently setting up a FL bushing die. You don't state what brass is involved, but most .308s have very generous chamber neck diameters on the order of 0.344 inches. Your die is likely made to work with thin necked Winchester brass and is sizing down to 0.331 O.D. or less with the stem removed. That drastic downsizing in one step can easily create the runout you are seeing. As an experiment, try backing off the collet die a little, so that the RCBS neck die is only doing the final .003 amount of sizing. You may find the runout has disappeared. Even with my Lapua brass that I size to 0.336, I find that I have to size down in two steps to keep the runout low.
Too close for irons, switching to scope...
|
|
|
|
Joined: Jun 2005
Posts: 2,226 Likes: 2
Campfire Regular
|
Campfire Regular
Joined: Jun 2005
Posts: 2,226 Likes: 2 |
As an experiment I did shoot a 100 yard bench group with ammo having .004 to .006 runout that measured .63 inches at 100 for 5 shots with match iron sights. I prefer straight ammo though...
Too close for irons, switching to scope...
|
|
|
|
Joined: Jun 2004
Posts: 44,863 Likes: 4
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,863 Likes: 4 |
Just finished reading JB's article in the August Handloader on reloading dies. I have a 308 that is typically 1 1/2-2MOA and never seems to do any better. Haven't messed with it in a while but decided to start looking at my loads since the rifle has been tweaked every way I can think of. Put a few loaded rounds on the RCBS Casemaster and they were running out .006-.008 Hmmm... Checked a few fired cases and they ran out .001-.002. Took the stem out of my RCBS neck sizer 1 and sized a few cases and they ran out .006-.008 Huh??? Switched shell holders and tried a different press all with the same results. Can't believe a neck sizer can induce that much run out. Ran a few through a Lyman collet die 2 and they were .001-.002. Guess this one is going back to RCBS and probably ask them to replace it with a full length die since the Lyman is now my go to neck die. 1. Conventional neck sizers are bad for runout more often than not. 2. I'm pretty sure you meant Lee collet die.
|
|
|
|
Joined: Jun 2004
Posts: 44,863 Likes: 4
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,863 Likes: 4 |
I went through this issue with my .308 Palma rifle recently setting up a FL bushing die. You don't state what brass is involved, but most .308s have very generous chamber neck diameters on the order of 0.344 inches. Your die is likely made to work with thin necked Winchester brass and is sizing down to 0.331 O.D. or less with the stem removed. That drastic downsizing in one step can easily create the runout you are seeing. As an experiment, try backing off the collet die a little, so that the RCBS neck die is only doing the final .003 amount of sizing. You may find the runout has disappeared. Even with my Lapua brass that I size to 0.336, I find that I have to size down in two steps to keep the runout low. Preach on Brother! I load for a bunch of different 308's and that's why my Redding bushing die for 308 is mostly in retirement.
|
|
|
|
Joined: Jul 2001
Posts: 60,161 Likes: 13
Campfire Kahuna
|
Campfire Kahuna
Joined: Jul 2001
Posts: 60,161 Likes: 13 |
What mathman said.
Conventional neck-sizing dies often result in misaligned case necks due to one of the reasons mentioned in the article: They don't provide any support of the case body during sizing. The result is often misaligned necks, whether using the expander ball or not.
If you're going to use a conventional sizing die to neck-size, it's usually far better to use a full-length die backed out a little. They usually provide at least a little support for the case body, preventing the case from tilting as much when the neck's pulled back over the expander ball.
“Montana seems to me to be what a small boy would think Texas is like from hearing Texans.” John Steinbeck
|
|
|
|
Joined: Nov 2010
Posts: 37,152 Likes: 2
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,152 Likes: 2 |
Get a TruAngle tool for straightening rounds. Works great. I use a Sinclair concentricity tool, correct with the TruTool. Takes some practice, but works well. Agree that the Lee Collet neck sizer is about the cheapest way to load concentric ammo. Of course, you'll need a body die to set back the shoulder when the bolt gets hard to close. You can use a next size up FL die, i.e. .308 FL as a 7-08 body die, etc. Or, you can grind out the neck on a FL die such that the case neck doesn't contact the die. If you get a Deluxe Lee die set, it'll have the collet neck sizer and a FL sizer. I'm not a fan of their FL dies, making one into a body die is its highest and best use, IMO. Cheaper than buying a Redding body die and it works about as well. DF
|
|
|
|
Joined: Sep 2010
Posts: 4,004
Campfire Tracker
|
OP
Campfire Tracker
Joined: Sep 2010
Posts: 4,004 |
Shipped it off to RCBS yesterday. Asked that it be replaced with a FL die. When I got the Casemaster after reading Gun Gack, I checked reloads of several calibers (some necksized although I usually PFL size) and wondered what the big deal was. Everything was .002-.003 max run out, most were less. Couldn't believe how far out the 308's were. Every single case was .007, nothing less, nothing more. Lee (not Lyman, good catch MM) collet die seems to be the answer.
I am continually astounded at how quickly people make up their minds on little evidence or none at all. Jack O'Connor
|
|
|
|
Joined: Aug 2010
Posts: 48,113 Likes: 12
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Aug 2010
Posts: 48,113 Likes: 12 |
I'm glad that my properly adjusted RCBS fl die set produces run-out of .003" and less TIR. No need to fu ck around with all the bs you guys do...
I try to stick with the basics, they do so well. Nothing fancy mind you, just plain jane will get it done with style. You want to see an animal drop right now? Shoot him in the ear hole. BSA MAGA
|
|
|
|
Joined: Jul 2005
Posts: 23,506
Campfire Ranger
|
Campfire Ranger
Joined: Jul 2005
Posts: 23,506 |
I'm glad that my properly adjusted RCBS fl die set produces run-out of .003" and less TIR. No need to fu ck around with all the bs you guys do... Well thanks for telling everyone how you properly set your dies to get less runout..
Then STFU. The rest of your statement is superflous bullshit with no real bearing on this discussion other than to massage your own ego. Suckin' on my titties like you wanted me.
|
|
|
|
Joined: Jul 2005
Posts: 23,506
Campfire Ranger
|
Campfire Ranger
Joined: Jul 2005
Posts: 23,506 |
Me I start with a universal decapping die, then I take my sizing die run the stem all the way up until stops, then turn it one full turn down. Then resize my cases. This has eliminated run out for me. Mule deer talks about this occasionally and it’s covered in one of his books.
Then STFU. The rest of your statement is superflous bullshit with no real bearing on this discussion other than to massage your own ego. Suckin' on my titties like you wanted me.
|
|
|
|
Joined: Sep 2010
Posts: 4,004
Campfire Tracker
|
OP
Campfire Tracker
Joined: Sep 2010
Posts: 4,004 |
Yeah but with the neck sizer I had it produced .007 run out with the stem removed. That's why I went to the collet die.
I am continually astounded at how quickly people make up their minds on little evidence or none at all. Jack O'Connor
|
|
|
|
Joined: Jul 2005
Posts: 23,506
Campfire Ranger
|
Campfire Ranger
Joined: Jul 2005
Posts: 23,506 |
Yeah but with the neck sizer I had it produced .007 run out with the stem removed. That's why I went to the collet die. With that, that what bsa was trying to say/relay. A properly set up fl sizing die will eliminate run out for the most part. No need for a neck sizer or collet die.
Last edited by 79S; 07/14/19.
Then STFU. The rest of your statement is superflous bullshit with no real bearing on this discussion other than to massage your own ego. Suckin' on my titties like you wanted me.
|
|
|
|
Joined: Jun 2004
Posts: 44,863 Likes: 4
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,863 Likes: 4 |
Properly setting things up is important, but it doesn't have magical powers. I can easily demonstrate with a FL die that sizes great and straight with one make of brass, but not so well with another. This is because of different thicknesses, both sets of brass having very uniform necks.
|
|
|
|
Joined: Oct 2008
Posts: 7,263
Campfire Tracker
|
Campfire Tracker
Joined: Oct 2008
Posts: 7,263 |
I wonder if it was a 1970s era die? See the best die thread for JBs explanation.
"When you disarm the people, you commence to offend them and show that you distrust them either through cowardice or lack of confidence, and both of these opinions generate hatred." Niccolo Machiavelli
|
|
|
|
Joined: Sep 2007
Posts: 647
Campfire Regular
|
Campfire Regular
Joined: Sep 2007
Posts: 647 |
I forget which gun writer suggested it long ago. If you loosen the decapping stem about a half a turn you will load way more concentric ammo. A friend had a 7x57 ackley that the decapping stem was so crooked a resized case wouldn’t chamber.
Fred
Fourth Generation Border Rat
|
|
|
|
Joined: Feb 2004
Posts: 46,745
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Feb 2004
Posts: 46,745 |
I should check my 7x57 die. This gets me thinking for sure.
Camp is where you make it.
|
|
|
|
Joined: Nov 2010
Posts: 37,152 Likes: 2
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Nov 2010
Posts: 37,152 Likes: 2 |
Yeah but with the neck sizer I had it produced .007 run out with the stem removed. That's why I went to the collet die. With that, that what bsa was trying to say/relay. A properly set up fl sizing die will eliminate run out for the most part. No need for a neck sizer or collet die. With very good quality, concentric brass, maybe... To me the neck collet system is less neck thickness sensitive. You get optimal ammo without neck turning, etc. BR shooters weigh cases, sort accordingly, check neck thickness, turn necks, etc... I'm a hunter, not a BR shooter. I want the best ammo I can load without all that prep work. For me the neck collet/body die system seems to perform best in that setting. DF
|
|
|
|
680 members (16gage, 160user, 12344mag, 10ring1, 16penny, 1beaver_shooter, 66 invisible),
3,021
guests, and
1,407
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,617
Posts18,492,642
Members73,972
|
Most Online11,491 Jul 7th, 2023
|
|
|
|