|
Joined: Jun 2012
Posts: 17,101
Campfire Ranger
|
OP
Campfire Ranger
Joined: Jun 2012
Posts: 17,101 |
i have a rifle that if very difficult to close the bolt on loaded rounds using nickle plated brass, spent cases extract just fine. it does not have this issue with regular brass. does this make sense?
Last edited by gitem_12; 10/27/21.
The government plans these shootings by targeting kids from kindergarten that the government thinks they can control with drugs until the appropriate time--DerbyDude
Whatever. Tell the oompa loompa's hey for me. [/quote]. LtPPowell
|
|
|
|
Joined: Jun 2004
Posts: 44,860 Likes: 4
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Jun 2004
Posts: 44,860 Likes: 4 |
All brass sized the same way/amount?
|
|
|
|
Joined: Sep 2004
Posts: 8,173
Campfire Outfitter
|
Campfire Outfitter
Joined: Sep 2004
Posts: 8,173 |
It kinda makes sense - the coefficient of friction between nickel/steel and brass/steel is 50% higher. All other things being equal - e.g. sizing of case body and headspace.
|
|
|
|
Joined: Jul 2012
Posts: 2,586
Campfire Regular
|
Campfire Regular
Joined: Jul 2012
Posts: 2,586 |
If the coefficient of friction is playing any significant role in how easy it is to close the bolt your cases are oversize.
I'd be inclined to look at sizing as a potential issue here. Is it factory loads or reloads?
If reloads, were they fired in this rifle?
Are they perhaps over length? Or bulged at the case mouth from overcrimping? Or perhaps this batch is a bit out of spec, such as on head size or extractor groove depth. What action is it ? PF or CRF bolt action for example?
You could try painting one up with a Sharpie and then carefully chambering it, to see if you can find any points where it is a bit tight.
|
|
|
|
Joined: Jun 2012
Posts: 17,101
Campfire Ranger
|
OP
Campfire Ranger
Joined: Jun 2012
Posts: 17,101 |
factory loads or relaods, they all do the same thing
The government plans these shootings by targeting kids from kindergarten that the government thinks they can control with drugs until the appropriate time--DerbyDude
Whatever. Tell the oompa loompa's hey for me. [/quote]. LtPPowell
|
|
|
|
Joined: Jun 2006
Posts: 3,216
Campfire Tracker
|
Campfire Tracker
Joined: Jun 2006
Posts: 3,216 |
It kinda makes sense - the coefficient of friction between nickel/steel and brass/steel is 50% higher. All other things being equal - e.g. sizing of case body and headspace.
You sure about that? I think nickel has a lower coefficient of friction than brass.
|
|
|
|
Joined: Jan 2008
Posts: 5,173 Likes: 1
Campfire Tracker
|
Campfire Tracker
Joined: Jan 2008
Posts: 5,173 Likes: 1 |
Nickle brass sucks! Unless you have small base dies, I wouldn't reload it. It has always been my experience it doesn't move as well as regular brass.
|
|
|
|
Joined: Apr 2003
Posts: 6,835
Campfire Tracker
|
Campfire Tracker
Joined: Apr 2003
Posts: 6,835 |
Interesting. A friend, who is not a reloader, gave me a bunch of once fired nickle plated brass. I have reloaded it several times without any issues...
|
|
|
|
Joined: Apr 2011
Posts: 151,737 Likes: 14
Campfire Savant
|
Campfire Savant
Joined: Apr 2011
Posts: 151,737 Likes: 14 |
I’ve reloaded 7mag, no issue that I remember
|
|
|
|
Joined: Apr 2007
Posts: 3,362
Campfire Tracker
|
Campfire Tracker
Joined: Apr 2007
Posts: 3,362 |
Use a dedicated sizing die -- nickel cases scratch the sides. Adjust to fit your chamber...
|
|
|
|
Joined: Jun 2012
Posts: 17,101
Campfire Ranger
|
OP
Campfire Ranger
Joined: Jun 2012
Posts: 17,101 |
I reload them fine out of my 7 mag as well. I am wondering. but the 280s range from a bit stiff to close the bolt on to down right TOUGH to close the bolt on. fired cases extract with no issues at all
The government plans these shootings by targeting kids from kindergarten that the government thinks they can control with drugs until the appropriate time--DerbyDude
Whatever. Tell the oompa loompa's hey for me. [/quote]. LtPPowell
|
|
|
|
Joined: Jun 2005
Posts: 12,361 Likes: 1
Campfire Outfitter
|
Campfire Outfitter
Joined: Jun 2005
Posts: 12,361 Likes: 1 |
I use nickel brass almost exclusively for my .280 Remington custom Mauser. I've never had a problem with that brass. Paul B.
Our forefathers did not politely protest the British.They did not vote them out of office, nor did they impeach the king,march on the capitol or ask permission for their rights. ----------------They just shot them. MOLON LABE
|
|
|
|
Joined: Jun 2012
Posts: 17,101
Campfire Ranger
|
OP
Campfire Ranger
Joined: Jun 2012
Posts: 17,101 |
I use nickel brass almost exclusively for my .280 Remington custom Mauser. I've never had a problem with that brass. Paul B. Winchester or Federal these are Winchester.
The government plans these shootings by targeting kids from kindergarten that the government thinks they can control with drugs until the appropriate time--DerbyDude
Whatever. Tell the oompa loompa's hey for me. [/quote]. LtPPowell
|
|
|
|
Joined: Mar 2009
Posts: 4,413 Likes: 1
Campfire Tracker
|
Campfire Tracker
Joined: Mar 2009
Posts: 4,413 Likes: 1 |
I bought a hundred Rem. nickle brass for my 7mag in 1994.The brass was great.I know I loaded some of those cases a dozen times.I bought another hundred cases later in the early 2000's and that brass was horrible.Very inconsistent on the hardness of the brass causing big variation of neck tention.Some of it was so hard it was difficult seating bullets.I'm sorry,new brass should be soft.Never bought anymore after that.
~Molɔ̀ːn Labé Skýla~ As Bob Hagel would say"You should not use a rifle that will kill an animal when everything goes right; you should use one that will do the job when everything goes wrong."Good words of wisdom...............
|
|
|
|
Joined: Apr 2003
Posts: 6,835
Campfire Tracker
|
Campfire Tracker
Joined: Apr 2003
Posts: 6,835 |
I use nickel brass almost exclusively for my .280 Remington custom Mauser. I've never had a problem with that brass. Paul B. Winchester or Federal these are Winchester. Mine was Winchester 280. FWIW...
|
|
|
|
Joined: Jul 2004
Posts: 6,669
Campfire Tracker
|
Campfire Tracker
Joined: Jul 2004
Posts: 6,669 |
You could try painting one up with a Sharpie and then carefully chambering it, to see if you can find any points where it is a bit tight.
That's what I'd do first.
'Four legs good, two legs baaaad." ---------------------------------------------- "Jimmy, some of it's magic, Some of it's tragic, But I had a good life all the way." (Jimmy Buffett)
SotG
|
|
|
|
Joined: Oct 2013
Posts: 18,930 Likes: 1
Campfire Ranger
|
Campfire Ranger
Joined: Oct 2013
Posts: 18,930 Likes: 1 |
I bought a hundred Rem. nickle brass for my 7mag in 1994.The brass was great.I know I loaded some of those cases a dozen times.I bought another hundred cases later in the early 2000's and that brass was horrible.Very inconsistent on the hardness of the brass causing big variation of neck tention.Some of it was so hard it was difficult seating bullets.I'm sorry,new brass should be soft.Never bought anymore after that. Tried nickle plated brass once. Never again. Stuff is too hard for me.
Last edited by 10gaugemag; 10/28/21.
The last time that bear ate a lawyer he had the runs for 33 days!
|
|
|
|
Joined: Oct 2004
Posts: 26,571 Likes: 17
Campfire Ranger
|
Campfire Ranger
Joined: Oct 2004
Posts: 26,571 Likes: 17 |
|
|
|
|
Joined: Aug 2010
Posts: 48,106 Likes: 8
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Aug 2010
Posts: 48,106 Likes: 8 |
Interesting. A friend, who is not a reloader, gave me a bunch of once fired nickle plated brass. I have reloaded it several times without any issues... Same here. No problems. The only real issue with it is its hard on the trimmer. Wears them out twice as fast.
I try to stick with the basics, they do so well. Nothing fancy mind you, just plain jane will get it done with style. You want to see an animal drop right now? Shoot him in the ear hole. BSA MAGA
|
|
|
|
Joined: Aug 2010
Posts: 48,106 Likes: 8
Campfire 'Bwana
|
Campfire 'Bwana
Joined: Aug 2010
Posts: 48,106 Likes: 8 |
I bought a hundred Rem. nickle brass for my 7mag in 1994.The brass was great.I know I loaded some of those cases a dozen times.I bought another hundred cases later in the early 2000's and that brass was horrible.Very inconsistent on the hardness of the brass causing big variation of neck tention.Some of it was so hard it was difficult seating bullets.I'm sorry,new brass should be soft.Never bought anymore after that. 90's R-P is excellent stuff.
I try to stick with the basics, they do so well. Nothing fancy mind you, just plain jane will get it done with style. You want to see an animal drop right now? Shoot him in the ear hole. BSA MAGA
|
|
|
|
478 members (007FJ, 160user, 17CalFan, 12344mag, 10gaugeman, 10ring1, 41 invisible),
2,220
guests, and
1,183
robots. |
Key:
Admin,
Global Mod,
Mod
|
|
Forums81
Topics1,192,377
Posts18,488,483
Members73,970
|
Most Online11,491 Jul 7th, 2023
|
|
|
|